SMARTRG SR505N ADSL Modems/Routers User Guide

: June 6, 2024
: SMARTRG

Table of Contents

[
Read User Manual Online (PDF format)
Download This Manual (PDF format)

[

](https://manuals.plus/wp-content/uploads/2021/12/SMARTRG-logo.webp)

SMARTRG SR505N ADSL Modems/Routers

SMARTRG SR505N ADSL Modems Routers

Installation

Connect one end of the supplied DSL cable to the port labeled DSL on the gateway and connect the other end to the DSL wall jack installed by your provider.
For all other devices, connect an Ethernet cable from that device to any of the LAN ports on the gateway.
Plug the power cord into the wall outlet and into the power jack on the back of the gateway. For additional protection, connect the power cord to a surge pro-tector.
Turn on the unit by pressing the power button on the gateway.
Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to complete before you can begin using your Inter-net applications (browser, email, etc.). If you are unable to connect to the Inter-net, verify that all cable connections are in place and that the router’s power is turned on.

LED INDICATORS

The LEDs on the front of SR505n can assist you in better understanding the current state of your gateway.

LED INDICATORS

Quick Gateway Configuration

Logging in to your gateway

To change the settings on your gateway, you must log in the gateways’ interface. Make sure that you have completed the steps in “Installation” before you begin.

Open your internet browser application and type 192.168.1.1 into the address line.
The following screen appears. Wait while the gateway connects to your service provider. When the connection is complete, OK appears in green letters next to the Net-work icon.
Click the Manage gateway (advanced) link in the upper right. The login dialogue appears.
You may log in with the factory default credentials shown below.

Logging in to your gateway 2

Manual Configuration of the WAN
If the automatic connect process is unsuccessful, refer to the Advanced Setup

Layer 2 Interface and WAN Services sections of the Gateway User Manual to manually establish a connection.

WiFi Setup

Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page for both methods, and then follow the instructions for the method you desire.

In the left navigation bar, click Wireless ->Basic.
If not already selected, click Enable Wireless.
If desired, in the SSID field, enter the network name to which you want your client devices connected. Continue with the steps in the method you prefer.

WiFi Setup

WPS Method
If the device you wish to connect to the Internet via your SmartRG gateway supports the WPS secure WiFi connection method, you may follow these steps.

In the left navigation bar, click Wireless -> Security.
Select Enable WPS and click Apply/Save to commit your selection.
On the back of the gateway’s exterior, press the button labeled WPS.
Within 2 minutes, activate WPS on the 3rd party device to which you wish to connect. It may have a pushbutton on its exterior or a software interface is used to initiate WPS connection. To learn how to use the WPS feature on your client device, refer to its documentation.

Your device should now be connected to your router wirelessly using WPS. If you encounter problems with the WPS setup such as connection failure, refer to your client device for further instructions.

Manual Method
Set up your gateway’s parameters first, then:

In the left navigation bar, select Wireless > Security and scroll down to the Manual Setup AP section.
If your gateway supports multiple wireless networks, select the SSID of the network you wish to configure. You will need this ID for step 7.
Select the desired Network Authentication. Make sure that the host devices you intend to use support the selected authentication type.
Choose a WPA Passphrase and type it in this field. You will need this passphrase for step 7.
Select any desired encryption preferences in the lower three fields.
Click Apply / Save.
Follow the WiFi connection instructions provided with your client device to connect to the router. Use the SSID name you selected in Step 2. Then enter the passphrase that you entered in step 4 in the network setup screen of your WiFi client device.