hama 00176551 WiFi Wallswitch Instruction Manual

: June 3, 2024
: Hama

Table of Contents

hama 00176551 WiFi Wallswitch
Explanation of warning symbols and notes
Explanation of symbols used on the product label
Package contents
Safety instructions
Installation
Download the app
Setting options
Extended usage options with scenarios
Care and maintenance
Warranty disclaimer
RF exposure information
Declaration of conformity
Technical data
ABOUT COMPANY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

hama 00176551 WiFi Wallswitch

hama 00176551 WiFi Wallswitch-fig1

Thank you for choosing a Hama product.
Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.

Explanation of warning symbols and notes

Risk of electric shock
This symbol indicates a risk of electric shock from touching uninsulated product parts that may carry hazardous voltage.
Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.

Explanation of symbols used on the product label

The article may only be connected by a qualified electrician who complies with national regulations and those of the local energy supply company, and who has sufficient knowledge regarding installation locations, fire protection and electrical installation work.
The product is intended only for use inside buildings.
Attention! There is a risk of electric shock on contact.

Package contents

1x WiFi wall switch
2x screws

Safety instructions

Warning

The wall switch is part of the building installation. During planning and setup, the relevant national standards and directives must be observed. The device may only be operated on a 230 V 50 Hz AC voltage network. Work on the 230 V network must only be carried out by an electrician certified in your country. The applicable accident prevention regulations must be adhered to.
To avoid an electric shock from the device, please disconnect the mains voltage (switch off the automatic circuit breaker). Failure to comply with the installation instructions can cause fires or other hazards.
The installation must be carried out only in conventional flush-mounted sockets with a minimum depth of 40 mm.
When connecting to the device terminals, note the permissible cables and cable cross-sections for this.
Observe the circuit diagram carefully!
Do not use any heat-generating devices (such as electric blankets, coffee machines, etc.) with this product. There is a risk of fire and injury.
Do not use this product with any devices that are motorised or any devices that have a rotating component or tool. There is a risk of injury.
The product is intended only for use inside buildings.
Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
Do not continue to operate the device if it is visibly damaged
Only operate with closed safety covers.
Use the product only for the intended purpose.
Protect the product from dirt, moisture and overheating and use it in dry rooms only.
Do not use the product in the immediate vicinity of heaters, other heat sources or in direct sunlight.
Only use the article under moderate climatic conditions.
As with all electrical products, this device should be kept out of the reach of children.
Do not operate the product outside the power limits given in the specifications.
Do not use the product in areas in which electronic products are not permitted.
Do not use the product in a damp environment and avoid splashing water.
Do not drop the product and do not expose it to any major shocks.
Do not modify the product in any way. Doing so voids the warranty.
Dispose of packaging material immediately in accordance with the locally applicable regulations.
The product must only be operated on a supply network as described on the type plate.
Do not bend or crush the cable.
Before mounting, check that the wall you have chosen is suitable for the weight to be mounted. Also make sure that there are no electric, water, gas or other lines running through the wall at the mounting site.
Small splinters of glass can lead to injuries if touched. Dispose of the product immediately if it is damaged or splintered during application or use.
Only touch the damaged or splintered product on undamaged areas and the edge.
Be very careful while doing so, thoroughly wash your hands afterwards and avoid contact with face and eyes.

Installation

Switch off the relevant fuse (fuse box) for the room in which you wish to install the switch.
Check that the wires are de-energised using a suitable measuring device (e.g. multimeter).
Connect the WiFi touch wall switch as shown below:

hama 00176551 WiFi Wallswitch-fig2

Fit the switch into a suitable wall or surface-mounted socket.
Replace the glass cover on the switch and check that it has engaged properly.

Download the app

Download the Hama Smart Home (Solution) app from the Apple App Store or Google Play Store.
Open the Hama Smart Home (Solution) APP
The first time you use the app, you need to register and create a new account. If you already have an account, log in with your access details.
Follow the instructions in the app.

Integrating devices into the Hama Smart Home (Solution) app

After installing the switch, the blue LED flashes quickly. If it does not flash, press and hold the button for approx. 6 seconds until the LED starts to flash.
Open the app and sign in.
Press the “+ in the top right-hand corner to add a new device.
Choose Switches from the list.
Next enter your WiFi password and confirm with “NEXT”.
Now confirm that the blue LED is flashing quickly by ticking “Next step” and clicking “Next”.
Your switch is now connected.
Once the connection is successful, the LED stops flashing quickly and the app confirms that your switch has been connected. You can now assign it a different name if you wish.
Click Finish to end the process.
You can now attach the switch and configure it.
Note
A detailed description of the Hama Smart Home (Solution) App and its full scope of functions can be found in our App Guide at:

www.hama.com Article Number Downloads App Operating Instructions

Setting options

The following settings can be made in the app:

hama 00176551 WiFi Wallswitch-fig7

Switching switches on/off individually
Switch on all switches
Timeline settings
Switch off all switches
For extended usage options, scenarios can be created in the app. (See Section 8 and App Guide)

Timeline settings:
Switching on or off according to a set schedule

Extended usage options with scenarios

Scenarios and automated sequences that can be created in the app allow various combination options and usage options for these products, depending on the SmartHome products in your home. Programming is always via the app (see Section 4 of the App Guide) and will be offered / suggested to you on an individual basis.

Standard usage option

hama 00176551 WiFi Wallswitch-fig9

Extended usage option

hama 00176551 WiFi Wallswitch-fig10

Product characteristics
The motion sensor can be used for monitoring (push message to the smartphone when triggered) or for controlling other smart products (e.g. lamps).

Care and maintenance

Only clean this product using a lint-free, slightly damp cloth and do not use any harsh cleaners.
Ensure that no water is able to enter the product.

Warranty disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

RF exposure information

This device complies with the EU requirements for limiting the exposure of the general public to electromagnetic fields by means of health protection.
The device complies with RF specifications provided it is used 20 cm away from the body.

Declaration of conformity

Hama GmbH & Co KG hereby declares that the radio equipment type [00176551] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following Internet address: www.hama.com -> 00176551 -> Downloads.