NX-602A 60W 2.1 Channel Soundbar and Wired Subwoofer User Manual

: June 6, 2024
: NX

NX-602A 60W 2.1 Channel Soundbar and Wired Subwoofer

WELCOME

Thank You for a purchasing the NX-602A Please take the time to read the following safety warnings and operating instructions carefully

GETTING STARTED

Remove the sound system from the box
Remove any packaging from the product
Place the packaging inside the box and either or dispose of safely

SAFETY AND NOTICE

Read and understand all instructions before you use this product If damage is caused by failure to follow the instructions, the warranty does not apply

WARNING

Never remove the casing of the unit
Never lubricate any part of the unit
Never place the unit on other electrical equipment
Keep the unit away from direct sunlight, naked flames or heat
Never look into the laser beam inside the unit
Ensure that you always have easy access to the power cord, plug or adaptor to disconnect the unit from the power

SAFETY

Read these instructions
Keep these instructions
Read all warnings
Follow all instructions
Do not use the unit near water
Clean only with a dry clot
Do not block any ventilation openings Install in accordance with the manufacturer’s instructions
Do not install near any heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat
Protect the power cord from being walked on or pinched, particularly at plugs, electrical outlets, and the point where they exit from the unit
Only use attachments and accessories specified by the manufacturer
Unplug the unit during lightning storms or when unused for long periods of tim
Refer all servicing to qualified personnel Servicing is required when the unit has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the unit, the unit has been exposed to rain or moisture, does not operate normally, or has been droppe
The unit should not be exposed to dripping or splashing
Do not place any sources of danger on the unit (eg liquid filled objects, lit candles
Where the mains plug or an appliance coupler is used as the disconnect device, the disconnected device should remain readily operable
Make sure there is enough free space around the product for ventilation
Batteries (battery pack or batteries installed) should not be exposed to excessive heat such as sunshine, fire or the like
The unit must equipped with the appropriate batteries in order to function properly
Only recommended batteries should be use
Polarity must be respected in such a way as to avoid any short circuits
Don’t mix used and new batteries
Don’t mix alkaline, standard (carbon-zinc) andrechargeable (nickel-cadmium) batteries
Don’t recharge or try to open the batteries Don’t throwthe batteries in fire
Replace all batteries at the same time with new, identical batteries
Remove the batteries when unused for a long time

CARE FOR YOUR PRODUCT

Always unplug the unit when not in use and before cleaning
Do not play music at excessive volume levels as damage to hearing and or the equipment may occur
Do not use this unit in wet or damp conditions
Always disconnect the unit from the main power supply before cleaning Clean the appliance with a soft, lint free cloth Do not use abrasives or harsh cleaners

TECHNICAL SPECIFICATIONS

Power Supply: 230V – 50Hz
Total Consumption: 75W
Input Sensitivity: AUX IN 1000MV, LINE IN 775MV
Speakers Impedance: 4ohm
S/N (A): 75dB · THD (1kzHz, 1W): 05%
Frequency Response: 20Hz- 20KHz
Total Music Output: 60W

WHAT’S IN THE BOX

Check and identify the contents of your package:

Sound Bar and Subwoofer
Remote Control
User Manual
RCA cable
Line-in cable
Audio cable for subwoofer
AC adaptor

DESCRIPTION OF PARTS OVERVIEW OF THE MAIN UNIT

SD Card Socket:
Insert SD card to play files stored on an SD Card (SD card not provided) Note: Supports maximum 32GB SD Card
USB Socket:
Insert USB to play files stored on a USB drive (USB not provided) Note: Supports maximum 32GB USB drive
Audio in:
To connect external audio device
LED Indicator:
Shows the power and selected input
Power:
Red color LED shows unit in Stand-by mode
Mode:
Press Mode button to select Bluetooth /USB / Audio In mode
Skip to the previous track
Press and hold to decrease volume
Start or pause play
Skip to the next track
VOL+
Press and hold to increase volume
Optical in
Insert Optical Digital input
AUX in
Connect an external audio device with RCA cable
Subwoofer out:
To connect to Subwoofer
DC Power In
Wall Mount Bracket

OVERVIEW OF REMOTE CONTROL

POWER
Press to turn Unit in/out of Standby mode
BT
Press to select Bluetooth input
USB
Press to select USB input
SD
Press to select SD Card input
VOLUME+
Press to increase the volume
Press to skip to previous track
VOLUME
Press to Decrease volume
OPT
Press to select Optical input
MUTE
Press to Mute/Unmute
AUX
Press to select AUX Input
LINE IN
Press to select Line Input
Press to Pause/Play
Press to skip to next track

REPLACING BATTERY

The remote control works with lithium button cell CR2025 3V batteries When the remote no longer works you need to replace the batteries as follows:

Press the tab on the side of the battery cover to release it and allow the battery support to come out
Replace the battery paying attention to the correct orientation of the poles
Replace the battery support pushing it inside until you hear a “click”

ATTENTION: Danger of explosion if batteries are not inserted correct

GETTING STARTED POWER

CAUTION:

Risk of product damage! Make sure that the power voltage corresponds to the voltage printed on the back label
Risk of electric shock! When you unplug the AC power cord always pull the plug from the socket Never pull the cord
Before connecting the AC power cord, ensure you have completed all other connections Place the unit in the desired position and unravel the mains cable Insert the cable into the supply socket and switch on if applicable

AUTO STAND-BY

To save power, the Soundbar automatically switches to stand-by if:

No Audio is available from the connected input for more than 10 minutes
When the unit is power ON

INPUT MODE SELECTION

The LED will turn red in Standby mode, press the remote power button or the power button on the Soundbar to turn OFF Stand-by mode Th red LED will turn OFF indicating the unit is no longer in Stand-by mode

CONNECTING TO EXTERNAL AUDIO DEVICES

OPTICAL INPUT (REQUIRES AN OPTICAL CABLE, NOT PROVIDED)

Connect an Optical cable to the optical input on the back panel of the Soundbar Connect the other end of the Optical cable to the digital audio device
Press the button to turn the unit on
Press the MODE button repeatedly until the LED above LIN/OPT turns green

LINE INPUT (REQUIRES A 3.5MM CABLE, PROVIDED)

Connect a 35mm cable to the line input on the control panel of the Soundbar Connect the other end of the 35mm cable to an MP3 player or other compatible audio device
Press the button to turn the unit on
Press the MODE button repeatedly until the LED above LIN/OPT turns yellow
Use the controls on the connected device to begin playing audio via the sound system

AUXILIARY INPUT (REQUIRES RCA CABLE, PROVIDED)

Connect an RCA cable to the AUX Input on the back panel of the Soundbar Connect the other end of the RCA cable to the audio output on your DVD player, gaming system, television or other compatible \ equipment
Press the power button to turn the unit on
Press the MODE button repeatedly until the LED above AUX turns green
Use the controls on the connected device to begin playing audio via the sound system

USB/SD CARD INPUT (REQUIRES USB/SD CARD NOT PROVIDED)

Plug your USB flash drive or SD card into the USB socket or SD slot on the control panel of the Soundbar
Press Mode button until the LED above USB/SD turns green or yellow Green shows USB input is selected and yellow shows SD card input is selected Files should start playing automatically after input selection If not, press
Press the to select track
Press the VOL+/VOL to adjust the volume

NOTE: Maximum 32GB USB or SD card storage is supported

PAIRING WITH BLUETOOTH

A. PAIRING WITH A SMART PHONE’S BLUETOOTH
Please ensure your smart phone’s Bluetooth is turned on Specific pairing steps may vary with different cell phones Please refer to the user manual of your cell phone for further information The general pairing steps are as follows:

Keep the sound bar and Bluetooth cell phone within 1 metre of each other when pairing
Press button, and press the MODE button multiple times until the sound system enters Bluetooth mode The LED above Bluetooth will turn Blue signaling the unit is ready to be connected via bluetooth
Switch ON your smart phone’s Bluetooth function and search for Bluetooth devices After the search is completed, select “NX-602A” from the Bluetooth device list
Depending on the prompt received on your smart phone, enter password or PIN: “0000” and press “Yes” or “confirm”
After successful pairing, select “NX-602A” from the Bluetooth device list and press “connect”

B. PAIRING WITH STEREO TRANSMITTER’S BLUETOOTH Different
Bluetooth transmitters have different pairing methods Please refer to the user manual of your Bluetooth transmitter for further information The general pairing steps are as follows:

Keep Soundbar and Bluetooth transmitter within 1 metre of each other when pairing
Press button, and press the MODE button multiple times until the sound system enters Bluetooth mode The LED above Bluetooth will turn Blue signaling the unit is ready to be connected via bluetooth
Switch on your Bluetooth transmitter and let it enter pairing mode
Switch ON your transmitter’s Bluetooth function and search for Bluetooth devices After the search is completed, select “NX-602A” from the Bluetooth device list
Depending on the prompt received on your transmitter, enter password or PIN: “0000” and press “Yes” or “confirm”
After successful pairing, select “NX-602A” from the Bluetooth device list and press “connect”
NOTE: The sound bar will return to pairing mode automatically after disconnecting from a Bluetooth device

TROUBLESHOOTING

In order to save energy when the unit has no input, the unit will be switched to stand-by mode automatically It can be switched on by pressing the POWER button on Soundbar or remote
If there is an incoming call while Soundbar is connected to your cell phone for music playback, music will be paused when the call is answered and resume after the call is completed (Depending on cell phones, music may remain paused even after the call has ended)

Please do not discard electrical and electronic appliances in a regular waste disposal

Take them to a collection point
Some components in the NX-602A may be hazardous to health and the environment.

WARRANTY TERMS & CONDITIONS

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
This warranty is provided in addition to your rights under the Australian Consumer Law Directed Electronics Australia Pty Ltd (Directed Electronics) warrants that this product is free from defects in material and workmanship for a period of 12 months from the date of purchase or for the period stated on the packaging This warranty is only valid where you have used the product in accordance with any recommendations or instructions provided by Directed Electronics.
This warranty excludes defects resulting from alterations of the product, accident, misuse, abuse or neglect.
In order to claim the warranty, you must return the product to the retailer from which it was purchased or if that retailer is part of a National network, a store within that chain, along with satisfactory proof of purchase The retailer will then return the goods to Directed Electronics Directed Electronics will repair, replace or refurbish the product at its discretion The retailer will contact you when the product is ready for collection All costs involved in claiming this warranty, including the cost of the retailer sending the product to Directed Electronics, will be borne by you
Email:info@nx-tech.com.au

All Images, Information and Content are Copyright © 2020 Directed Electronics Australia Pty Ltd. All Rights Reserved.
www.directed.com.au | www.directed.co.nz

www.nx-tech.com.au | www.nx- tech.co.nz