RMCE-BT2 Shure Bluetooth Earphones User Guide
- June 6, 2024
- Shure
Table of Contents
BT2 — Shure Bluetooth® Earphones
User Guide
Bluetooth Pairing
- Turn off the earphones. Press and hold the center button on the earphone remote until the LED flashes blue and red.
- From your audio source, select “Shure BT2.”
- When successfully paired, the LED turns blue.
Note: If the pairing fails on the first attempt, repeat the process from
the beginning.
For additional pairing methods, please visit http://www.shure.com/earphones
(http://www.shure.com/earphones).
The best sound starts with a good fit
- Select the sleeve that provides a snug fit (like earplugs).
- Secure the cable behind the ear to maintain a tight seal.
To keep them sounding their best…
- Clean regularly to remove debris and deposits.
- Contact Shure Service and Repair to replace the damaged product. Simply detach and return the broken earpiece for easy replacement.
Changing Sleeves
- Gently twist and pull to remove sleeve.
- Install the new sleeve so it completely covers the barb and nozzle.
Visit http://www.shure.com/earphones (http://www.shure.com/earphones) for replacement parts and important in instructions on cleaning and maintenance.
Using the Remote
The Center Button
| Power on | Press and hold |
|---|---|
| Power off | Press and hold, 5 seconds |
| Pair Bluetooth | Turn off the earphones. Press and hold, 7 seconds |
| Play/Pause | Click once |
| Answer/End a call | Click once |
| Decline a call | Press and hold, 3 seconds |
| Activate voice assistant | Phone on, press and hold, 3 seconds |
| Factory Reset | Turn off the earphones and plug into a charger. |
Press and hold, 15 seconds. Hold past pairing mode until earphones turn off
again.
Volume Up/Down| Click + or –
Next track| Press and hold +, 3 seconds
Previous track| Press and hold -, 3 seconds
Check battery status| Press and hold + and – together, 3 seconds
Your phone may not be compatible with some functions. Visit http://www.shure.com/earphones (http://www.shure.com/earphones) for more information.
Charging the Earphones
Red LED indicates low battery.
- Connect the earphones to a charging device using the supplied USB cable.
- The LED is red while charging.
- When fully charged, the LED turns off.
Warning: Before charging, make sure the product is at room temperature,
between 10 to 45°C (50 to 113°F).
Note: Use this product only with an agency-approved power supply that
meets local regulatory requirements (e.g., UL, CSA, VDE, CCC, INMETRO).
Specifications
Antenna Information:
- Type = Chip
- Gain = +1.6 dBi
Bluetooth 5:
- Operating frequency = 2402MHz-2480MHz
- Modulation scheme = FHSS
- RF power = +7.45dBm (E.I.R.P.) (for EU)
Supported Codecs:
- aptX™
- aptX HD
- aptX Low Latency
- SBC
- AAC
Safety Information
Visit http://www.shure.com/earphones (http://www.shure.com/earphones) for the latest regulatory and compliance information.
WARNING
-
Follow instructions from the manufacturer.
-
Product battery may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disas
semble, heat above 140°F (60°C), or incinerate. -
Attention should be drawn to the environmental aspects of battery disposal.
-
The product shall not be exposed to excessive heat such as sunshine, fire, or the like.
-
Do NOT make unauthorized alterations to this product.
Note: Battery replacement to be performed only by Shure authorized
service personnel.
CAUTION: Follow applicable laws regarding mobile phone and headphone use
while driving.
This product contains magnetic material. Consult your physician on whether
this might affect your implantable medical device.
High sound pressure
Hearing damage risk
To prevent possible hearing damage, do not listen at high volume levels for
long periods.
Information to the user
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harm ful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including in interference that may cause undesired operation.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s au authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES003. Cet appareil
numérique de la classe B est con forme à la norme NMB-003 du Canada.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any inter ference, including interference that may cause undesired operation of the device
Note: Testing is based on the use of supplied and recommended cable types. The use of other than shielded (screened) cable types may degrade EMC performance.
|
---|---
The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Shure Incorporated is under license. Other trademarks and trade names are those of their respec tive owners.
Environmentally-friendly disposal
Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of sep arately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little person al effort, you contribute to recycling valuable raw materials and the treatment of toxic substances.
Qualcomm® aptX is a product of Qualcomm Technologies, Inc. and/or its
subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United
States and other countries. aptX is a trademark of Qualcomm Technologies
International, Ltd., registered in the United States and other countries.
Certifications
This product meets the Essential Requirements of all relevant European
directives and is eligible for CE marking.
Hereby, Shure Incorporated declares that the radio equipment is in compliance
with Directive 2014/53/EU. The full text of the EU declaration of conformity
is available at the following internet address:
http://www.shure.com/europe/compliance
(http://www.shure.com/europe/compliance) Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Fax: +49-7262-92 49 11 4
Email: EMEAsupport@shure.de
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>