TOSIBOX Lock 210 Robust Industrial VPN Router for All Network User Guide

June 6, 2024
TOSIBOX

TOSIBOX - logo

Lock 210/250
Quick Start GuideTOSIBOX Lock 210 Robust Industrial VPN Router for All
Network - icon5Copyright © Tosibox Oy, 2020

Matching the Lock with the KeyTOSIBOX Lock 210 Robust Industrial VPN
Router for All Network

1. Connect the operating voltage of 12-48 V DC to the Lock and wait for 1 minute. In case you have a  product version with a Power Source kit, use the conversion cable. It onverts the AC adapter’s coaxial connector output to stripped wires that are needed to power the Lock 210/250. Follow the polarity symbols in the front panel. Use + and –  terminals to power the device.
2. Insert the Key into the USB port of the Lock. When the LED on the Key turns off, (after approx. 10 seconds) the matching is complete, and you can remove the Key from the USB port.
3. Go to 2a if deploying into broadband networks (ethernet) or 2b if deploying into mobile networks. If deploying Locks as DHCP client into existing networks, please see the TOSIBOX ® user manual.

Deploying into Broadband Networks

TOSIBOX Lock 210 Robust Industrial VPN Router for All Network - Broadband
Networks

1. Connect an Internet-connected ethernet cable to the Lock’s WAN port.TOSIBOX Lock 210 Robust Industrial VPN Router for All Network - DSL
router

WAN: Internet/xDSL router
2. Plug the devices into the Lock’s LAN ports (LAN 1-3). If the devices have static IP addresses, please see Deploying the Lock in the TOSIBOX ® user manual.

Deploying into Mobile Networks with a USB modem
You can connect the Lock to the Internet with a USB Modem.
1. Connect a computer to the Lock’s service port with an Ethernet cable.
2. Type http://172.17.17.17 into your browser’s address field to access the Lock’s user interface. Log in using the “admin” account. The password can be found at the bottom of the Lock. Select Network > USB modem and either uses the automatic APN settings or fill in the APN according to your mobile operator settings. Enter PIN code if necessary. Click Save.
3. Plug a supported USB modem into the USB port of the Lock.
4. Plug network devices into the Lock’s LAN ports (LAN 1-3) or connect wirelessly via WLAN (Lock 250 only). See Deploying the Lock in the user manual for static IP  configurations.
5. Verify on the Lock user interface status page that the Internet connection is OK. This is also indicated on the front panel with the symbol.
For more information and the latest supported modem models, visit www.tosibox.com/support.

Using the Key
To install the Key software, insert the TOSIBOX ® Key into the USB port of your computer.![TOSIBOX Lock 210 Robust Industrial VPN Router for All Network

The TOYBOX ® Key user interface shows all Lock devices matched to the Key and the network devices connected to them. For more options, click or .
The Lock is connected o the Internet and the Key has a remote connection to the Lock.
The Lock is connected to the Internet, but the Key doesn’t have a remote connection to the Lock.
The Lock is not connected to the Internet.

DECLARATION OF CONFORMITY
Hereby, Tosibox Oy declares that the radio equipment type Lock 210/250 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is  available at www.tosibox.com/documentation-and- downloads
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This device complies with FCC part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Lock 250 FCC
ID: 2AHCNLOCK500iC.
This radio device has been tested to operate with the external antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna  ype indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Lock  250: Wi-Fi monopole antenna, 50 ohm, max peak gain 2.0 dBi.
This device is UL listed in USA and Canada with UL file number E497243.TOSIBOX Lock 210 Robust Industrial VPN Router for All Network -
icon4 INDUSTRY CANADA STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and  2) this device must accept any interference, including interference that may cause undesired operation of the device.
This radio transmitter IC: 25009-LOCK500iC has been approved by ISED to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Lock 250:
Wi-Fi monopole antenna, 50 ohm, max peak gain 2.0 dBi.
Under ISED regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication!
This equipment should be installed and operated with a minimum distance of 20 cm between the antenna and the user or bystanders. Patented, incl. US8831020, US9900178.
Patents pending, incl. US14/119753, US14/39015.

Compliance with IMDA Standards DB107332
IMDA Standard applies to TBL21 and TBL25
Download user manual
www.tosibox.com/documentation-and-downloads
Visit Support
www.tosibox.com/support/
TOYBOX ® Lock 210/250 Quick Start Guide v1.0
www.tosibox.com 
info@tosibox.com

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals