TOSIBOX 600-series Router User Guide
- June 6, 2024
- TOSIBOX
Table of Contents
610, 650, 670, 675
Quick Start Guide
Copyright © Tosibox Oy, 2021
Matching your TOSIBOX® Node with the Key
- Connect the operating voltage of 9-50 V DC to the Node and wait for 1 minute.
- Insert the Key into the USB port of the Node. When the LED on the Key turns off, (after approx. 10 seconds) the matching is complete, and you can remove the Key from the USB port.
- Go to
**3a**if you are connecting to the Internet using Ethernet connection or**3b**if setting up wireless connection. If deploying Nodes as DHCP client into existing networks, please see the TOSIBOX® user manual.
Set Up Router
- Connect ethernet cable into LAN port of TOSIBOX® Node and the other end of the cable into LAN port of your computer.
- Visit 10.10.10.254 in your browser to set up your device.
- Log in using “admin” account. The password can be found from the bottom of the Node.
- TOSIBOX® Node needs an Internet connection to function. Go to
**3a**if deploying into broadband networks (ethernet) or**3b**if deploying into wireless connection.
Update the device software immediately when you are connected to the Internet. Go to Settings > Software update. If there is a software update available for the device, start the update by clicking Start software update.
Connect to the Internet using Ethernet connection
- Connect your TOSIBOX® Node from the WAN port to the Internet with a fixed Ethernet cable.
- When the WAN ETH LED is lit on the front plate of the Node, the Internet connection is working. If the light is not lit, investigate possible connectivity issues.
Set up wireless connection
Connect the device to the Internet using internal LTE Modem (670 and 675)
You can connect the device to the Internet with an internal Modem. Before
inserting or removing the SIM card, disconnect the device power supply.
- Install the antenna
- Insert a SIM card
- Select Network > Internal Modem and fill in the APN according to your mobile operator settings. Enter PIN code if necessary. Click Save.
Connect the device to the Internet using wireless LAN (650 and 675)
- Attach WLAN antenna to the device.
- Open the service connection to the device and log in with your credentials.
- Configure wireless LAN settings at “Network > WLAN”.
- When the WAN WIFI LED is lit on the front plate of the Device, the WLAN connection is working.
Position the antennas in orthogonal pattern, i.e. in such a way that they form 90 degrees angle between each other.
Using the Key
To install the Key software, insert the TOSIBOX® Key into the USB port of your
computer.
The TOSIBOX® Key user interface shows all Nodes matched to the Key and the
network devices connected to them. For more options, click or .
The Node is connected to the Internet and the Key has a remote connection to
the Node.
The Node is connected to the Internet, but the Key doesn’t have a remote
connection to the Node.
The Node is not connected to the Internet.
DECLARATION OF CONFORMITY
Hereby, Tosibox Oy declares that the radio equipment type 610, 650, 670 and
675 are in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at www.tosibox.com/documentation-and-
downloads
Patented, incl. US8831020, US9900178, US14/119753, US14/39015
TOSIBOX® 650 and 675: Wi-Fi monopole antenna, 50 ohm, max peak gain 3.5 dBi.
This equipment should be installed and operated with a minimum distance of 20
cm between the antenna and the user or bystanders.
| |
---|---|---
Visit Support, download user manual
www.tosibox.com/support/
TOSIBOX® 600 SERIES Quick Start Guide
www.tosibox.com
info@tosibox.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>