victron energy SCC900650010 Energy SmartSolar Control Display User Manual

June 6, 2024
victron energy

victron energy logo

victron energy SCC900650010 Energy SmartSolar Control Display

victron energy SCC900650010 Energy SmartSolar Control Display
featured

Introduction

The SmartSolar Control display is a dedicated display for the following MPPT solar charger ranges:

  • SmartSolar MPPT 150/45 up to 250/100
  • SmartSolar MPPT 150/70 up to 250/100 VE.Can
  • BlueSolar MPPT 150/70 up to 250/100 VE.Can

These solar chargers can also be recognized by a small plastic cover on the front face with the text “display option”.
victron energy SCC900650010 Energy SmartSolar Control Display
fig1

Example of a solar charger without display and with display
The display plugs directly into the front face of the solar charger. It can act as both a permanent or a temporary display. Simply remove the plastic cover that protects the display terminal on the front of the controller and then plug in the display.
The display can be used to monitor the solar charger and to view both live and historic data. The display can also be used to configure solar charger settings.

Examples of live and historic monitoring:

  • PV power, yield, voltage and current.
  • Battery voltage, current and charge stage.
  • Load output state and current (only available if the solar charger is equipped with a load output).
  • 30-day historical values.
  • Cumulative historic values over the live of the solar charger.

Installation

The display connects to the display terminal on the front of the solar charger. The display terminal is located behind the plastic cover with the text: “display option”.
To install the SmartSolar Control display do the following:

  1. Remove the two screws of the plastic cover. Keep the screws, they are needed again when securing the display.
  2. Remove the plastic cover. The display terminal is now exposed.
  3. Remove the two plastic plugs on either side of the display plug.
  4. Remove the paper backing of the double sided tape on the back of the display.
  5. Insert the display into the plug and make sure it has been inserted all the way in.
  6. Screw the display down by using the two screws that were used for the plastic cover.

victron energy SCC900650010 Energy SmartSolar Control Display
fig2How and where to connect the SmartSolar Control display

Note:

  • If the display is used as a temporary display, it is not necessary to use the tape and to screw down the display into the solar charger.
  • The display is hot-swappable, this means that the display can be plugged in or removed while the solar charger is operating.

Operation

The LCD screen displays the following information:

  • A number reading.
  • The unit of the reading: V, A, W, kWh, h or °C/°F.
  • The type of reading: battery, PV or temperature.
  • State: charge and charge stage indication.
  • Connection indicator and warning indicator.

victron energy SCC900650010 Energy SmartSolar Control Display
fig3

The digits used to represent letters and numbers
The buttons on the front of the display are used to navigate through the solar charger readings and are used when making solar controller and display settings.They have the following functions:

victron energy SCC900650010 Energy SmartSolar Control Display
fig4

Status menu
This menu shows the live solar charger readings. The SmartSolar Control display always starts up in this menu. Press the – and + button to cycle through all menu items.
Press the – button to see the live data of the solar charger. Each time the – button is pressed, the next parameter will be displayed.
If the + and – button is pressed at the same time for 4 seconds, the auto scroll mode will be activated. The display will continuously cycle through each menu item every 5 seconds. To stop the auto scroll mode, briefly press the “-” or the “+” button.
These menu items will be displayed in order of appearance as indicated in below table:

victron energy SCC900650010 Energy SmartSolar Control Display
fig5 victron energy
SCC900650010 Energy SmartSolar Control Display fig6 victron energy SCC900650010 Energy SmartSolar Control
Display fig7

In addition to above menu items, the following menu items will appear when special conditions occur:

victron energy SCC900650010 Energy SmartSolar Control Display
fig8

The charge stage and if PV is active is indicated by the bottom line of the display:

victron energy SCC900650010 Energy SmartSolar Control Display
fig9

History menu
The history menu shows both the daily and overall solar charger history data. It shows items such as solar yield, battery voltages, time spend in each charge stage and past errors.
To enter and read out the historical menu:

  • Press the SELECT button, while in the status menu.

  • A scrolling text will be visible.

  • Press the + or – button to navigate through the history items.

  • When arriving at the desired history item, press the SELECT button to see the value of that item.

  • If an item contains multiple values, Press + or – button to browse the various values within that item.
    For the daily items it is possible to scroll back to 30 days ago (data becomes available over time), a brief popup shows the day number.

  • To go back to the main history menu, press the SETUP button.

  • To go back to the status menu, press the SETUP button again.

All available history menu items are listed in below table, in the order they appear when scrolling through the items.

victron energy SCC900650010 Energy SmartSolar Control Display
fig10 victron energy
SCC900650010 Energy SmartSolar Control Display fig11 victron energy SCC900650010 Energy SmartSolar Control
Display fig12

victron energy SCC900650010 Energy SmartSolar Control Display
fig13

Setup menu
In the settings menu the solar charger and SmartSolar Control settings can be viewed and/or changed.

Note:
Do not change settings unless you know what they are and what the effect of changing these setting can be. Incorrect settings may cause system problems including damage to batteries. When in doubt, seek advice from and experienced Victron Energy installer, dealer or distributor.

To navigate the settings menu:

  • Press the SETUP button for 3 seconds to enter the setup menu.
  • The display will show the text “Menu” and the first menu item is shown via a scrolling text.
  • Navigate to the desired setting by pressing the – or + button.
  • Once arrived at the desired setting press the SELECT button to view the value the setting has been set to.
  • To modify this setting press the SELECT button again, the value will now blink.
  • Press the – or + button to choose the desired value.
  • Press SELECT to confirm the change, the value will stop blinking, and the change is made final.
  • Navigate to the next menu item, or press SETUP to return to the setup menu.
  • To leave the setup menu, press the SETUP button.

Any settings change via the display or the VictronConnect App will override the rotary switch setting. Turning the rotary switch will override settings made with the display or via the VictronConnect App.

All available settings are indicated in below table, in the order they appear when scrolling through the menu, together with a basic description and notes for each setting. For the full description of the solar charger settings refer to the solar charger manual.

victron energy SCC900650010 Energy SmartSolar Control Display
fig14

victron energy SCC900650010 Energy SmartSolar Control Display
fig15victron energy
SCC900650010 Energy SmartSolar Control Display fig16victron energy SCC900650010 Energy SmartSolar Control
Display fig17victron energy
SCC900650010 Energy SmartSolar Control Display fig18victron energy SCC900650010 Energy SmartSolar Control
Display fig19 victron energy
SCC900650010 Energy SmartSolar Control Display fig20victron energy SCC900650010 Energy SmartSolar Control
Display fig21victron energy
SCC900650010 Energy SmartSolar Control Display fig22victron energy SCC900650010 Energy SmartSolar Control
Display fig23victron energy
SCC900650010 Energy SmartSolar Control Display fig24 victron energy SCC900650010 Energy SmartSolar Control
Display fig25

Troubleshooting and Support

Consult this chapter in case of unexpected behaviour or if you suspect a product fault.
The correct troubleshooting and support process is to first consult the common issues as described in this chapter.
Should this fail to resolve the issue, contact the point of purchase for technical support. If the point of purchase is unknown, refer to the Victron Energy Support webpage.

The display does not power up
The display does not power up. The screen is blank and the back-light is off.
The display is powered from the solar charger. The solar charger is powered from either the battery or the PV array. If the PV voltage and the battery voltage are both below 6V, the display will not power up.
It could also be that the LCD display is not properly inserted into the socket on the solar charger.

The display segments are faint or missing
The screen is blank or faint, but the back-light is still operational.
This may be due to low ambient temperature. If the ambient temperature is below -10°C (14°F), the LCD segments can become faint. Below -20°C (-4°F) the LCD-segments can become invisible.
During charging the LCD-display will warm up, and the LCD segments will become visible again.

Display keeps scrolling through different menu items
The display is in “auto scroll mode”. In this mode the display will continuously cycle through each live data menu item every 5 seconds.
To stop the auto scroll mode, briefly press the “-” or the “+” button.

Settings locked
If the setup menu is locked settings can only be viewed but not changed.
To unlock the settings menu see the instruction in the Setup menu [7] chapter.

Warranty

This product has a 5-year limited warranty. This limited warranty covers defects in materials and workmanship in this product and lasts for five years from the date of original purchase of this product. To claim warranty the customer must return the product together with the receipt of purchase to the point of purchase. This limited warranty does not cover damage, deterioration or malfunction resulting from alteration, modification, improper or unreasonable use or misuse, neglect, exposure to excess moisture, fire, improper packing, lightning, power surges, or other acts of nature. This limited warranty does not cover damage, deterioration or malfunction resulting from repairs attempted by anyone unauthorized by Victron Energy to make such repairs. Non-compliance with the instructions in this manual will render the warranty void. Victron Energy is not liable for any consequential damages arising from the use of this product. The maximum liability of Victron Energy under this limited warranty shall not exceed the actual purchase price of the product.

Specifications

Technical specifications

Installation type| Inserts into the display port on the front of a solar charger.
Suitability| Suitable for the Victron Energy 150V and 250V BlueSolar and SmartSolar MPPT solar charger range that are equipped with a display port.
Display port connector| RS232 9 pin pinout
Dimensions (w x l x h)| 116mm x 50mm x 25mm
Weight| 66g

victron energy SCC900650010 Energy SmartSolar Control Display
fig26

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

victron energy User Manuals

Related Manuals