SONOFF LBS L1 Lite Wi-Fi Smart LED Light Strip User Manual

Wi-Fi Smart LED Light Strip
LBS L1/L1 Lite
User manual V1.1

Operation instruction

1. Clean the surface

2. Tear the backing tape

3. Adhere it to the surface

4. Download APP
   http://app.coolkit.cc/dl.html

5. Power on Cutable every 100mm

6. Pull out the insulation sheet, then long-press the “on” button for 5s until the light strip “flashes”, which means it enters the quick pairing mode. The device will exit the quick pairing mode if not paired within 3mins. If you want to enter this mode again, long-press the “on” button on the remote controller for 5s until the light strip “flashes” and release it.

7. . Tap “+” and select “Quick Pairing”, then operate following the prompt on the app.

Compatible Pairing Mode

If you fail to enter Quick Pairing Mode (Touch), please try “Compatible Pairing Mode ” to pair.

1. Long press the “on” button on the remote controller for 5s until the device “flashes” and releases. Long press this button for 5s again until the device status changes from “flashing” to “quick flashing”, then the device enters the Compatible Pairing Mode.
2. Tap “+” and select “Compatible Pairing Mode ” on APP.
   Select Wi-Fi SSID with ITEAD-** and enter the password 12345678, and then go back to eWeLink APP and tap  Next”. Be patient until pairing completes.

Specifications

Model: L1-2M/L1-5M/L1 Lite-5M-EU/L1 Lite-5M-US
LED Light Strips

L1 Lite: IP20
Material| FPCB
Light Decay| Less than 3% after 1000 hours constant work

Power Adapter

Wi-Fi Controller

Features of the Smart LED Light Strip

● SMD5050 LED Beads; FPCB Circuit Board; Every 3 LED lights in one segment.
● Main Colors of the Light: Red/Blue/Green.

Factory Reset

Long press the “on” button on the remote controller for 5s until the device starts flashing, then the device has been reset successfully and enters the quick pairing mode.
When the light strip is used on a new network, it must first be reset to its factory settings and then set up again on the new network.

Safety Warning

1.  Before using this product, please make sure that your voltage is appropriate for this product’s working voltage. Using this product with a voltage other than the one specified may damage the product and cause safety hazards.
2.  LED Light Sources are unchangeable, please don’t dismantle them.
3.  While the Light Strip is working, it will generate heat so please keep it in a cross-ventilation environment for heat dissipation.

FCC Warning

Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type L1-2M/L1-5M/L1 Lite-5M-US/L1 Lite-5M-EU is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the  following internet address: https://sonoff.tech/usermanuals

Shenzhen Sonoff Technologies Co., Ltd.
1001, BLDG8, Lianhua Industrial Park, Shenzhen, GD, China
ZIP code: 518000
Website: sonoff.tech
MADE IN CHINA

Documents / Resources

| SONOFF LBS L1 Lite Wi-Fi Smart LED Light Strip [pdf] User Manual
LBS L1 Lite, LBS L1, LBS L1 Lite Wi-Fi Smart LED Light Strip, Wi-Fi Smart LED Light Strip
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>