FCi ASD-0001 Magic Round Automatic Soap Dispenser

June 6, 2024
FCi

FCI

FCi ASD-0001 Magic Round Automatic Soap Dispenser

product

MagicRound Automatic Soap Dispenser
ASD-0001
Installation Manual

Quality Guarantee
Thank you for choosing the automatic wall mount soap dispenser. Please read the instruction carefully before installation. This manual is for your reference only.

Features

  • Hands free sensor operation improves hand washing
  • Easy installation and low-cost maintenance
  • Battery
  • Stainless steel finish
  • Suitable for schools, offices, supermarkets, hospitals, and other high- volume facilities

Specifications

Power Supplied 9V (6 x AA Alkaline batteries)
Sensing Range 5 – 15 cm
Soap Vol per Drop 1 ml
Soap Bottle Volume 650 ml
Ambient Temperature 1 – 45 oC

Before Installation

  • Locate position of soap
  • Ensure that soap dispenser does not interfere with anything above the lavatory/counter or shining surface top area. Must be installed 250 mm above the counter.
  • Pay special attention so that the sensor surface is not flawed or scratched during the installation
  • Before installing on the wall, check that no other piping and wiring is running behind hole locations. Wall should be sufficiently reinforced or risk failure due to soap case unit
  • Do not place other devices that use an inverter or infrared sensor near the faucet, as this may cause the faucet to malfunction.

Tools You will Need

  • Power drill with 6 mm wall drill bit
  • Flat head screwdriver
  • Phillips screwdriver
  • Ruler/tape measureTools

Part List

Partlist

Construction / Installation Diagram

  1. Using the supplied black plastic key, open & remove the upper cover.
  2. Disconnect the battery power and remove the battery holder
  3. Using a Philips screw driver remove the upper right-hand Phillips screw and remove the steel wall mount plate (wall build-up frame)
  4. Use the steel plate as a guide, mark where holes need to be drilled. Important: Make sure bracket and case unit is mounted level
  5. When installing onto a concrete wall, drill holes 30 mm deep using a 6 mm masonry drill bit. Insert wall anchors into the holes and mount the plate using the screws.
  6. Slide & assemble the dispenser onto the plate tongues, ensuring the dispenser is secured by the two tongues.
  7. Remove the white plastic cap & fill the soap cartridge with soap. Do not overfill the soap cartridge to the top the
  8. Assemble back the battery holder and tighten the holder onto the upper
  9. Connect the battery power
  10. Place & close the upper cover onto the
  11. Remove the white sensor film from underneath the sensor.

underneath the sensor

123456

Operations

As the user’s hands enter below the beam’s effective range (5 – 15 cm), the beam is reflected back into the sensor receiver and activates the solenoid valve allowing a single soap application to flow from the dispenser.

operations

Soap Volume Adjustment

No adjustments are required for most settings. Factory default soap volume is 1 ml. The factory setting should be satisfactory for most installations.

To invoke the volume adjustment, press the button below the dispenser and hold it until the LED starts flashing slowly, about five seconds. Press the button again and hold until the LED flashes for approximately 5 seconds and flashing continuously.

Place a medium target such as small card board under the dispenser nozzle until the desired volume has been reached. Remove the target to complete setup.

Soap Dispensing Range Adjustments

No adjustments are required for most settings. Factory default range is set at 1 cm. The factory setting should be satisfactory for most installations.

To invoke the sensing range adjustment, press the button below the dispenser and hold it until the LED starts flashing slowly, about five seconds. Press the button again and hold for 5 seconds until the LED flashes continuously.

Place a medium target such as small card board below the sensor eye at the desired range until the LED stops flashing. Remove the target to complete setup.

Battery Replacement

The sensor LED will flash continuously & rapidly to indicate low battery power.

  1. Using the supplied black plastic key, open & remove the upper cover.
  2. Disconnect the battery power and remove the battery
  3. To remove the battery holder, unfasten the two Phillips screw from the upper
  4. Remove the 6 AA size batteries and replace with new AA batteries
  5. Place back the holder and securely tighten the two Phillips screws
  6. Assemble back & close the upper cover.

Troubleshooting

  1. Unit does not operate
    • Check battery. Remove & replace 3 AA size batteries.
  2. Soap does not dispense
    • Soap bottle needs refill. Refill soap.
    • Check soap dispensing nozzle for clog. Clean nozzle with soft cloth.

Care & Cleaning

DO NOT USE abrasive or chemical cleaners (including chlorine bleach) to clean dispenser that may dull the luster and attack the special decorative finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. While cleaning the bathroom tile, protect the dispenser from any splattering of cleaner. Acids and cleaning fluids will discolor or remove decorative finish.

Resources

For Installation guides, visit our resource page through the QR code.
Alternatively, you can visit our resource page at https://faucetscanada.ca/resources/

To view more products from Faucets Canada, visit our shop page through the QR code.
Alternatively, you can visit our shop page at https://faucetscanada.ca/shop/

Warranty Information

For information on product warranty, visit our resource page through the QR code.
Alternatively, you can visit our warranty claims page at https://faucetscanada.ca//warranty-claim/

About us

Here at FCi, our main goal is to break the eco- innovation boundary and provide customers with fixtures that save water and deliver reliable sources of sanitation every time.

As Canada’s favourite automatic faucet brand, we are proud to say we deliver quality touchless fixtures that perform beyond expectations and exceed design standards.

To learn more about Faucets Canada, please visit our website at FacucetsCanada.ca

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals