Ride1UP Intelligent OLED Display SW102 User Manual

: June 6, 2024
: Ride1UP

SW102 Display technical specifications
Product Name:Intelligent OLED display
Part Number: SW102

Product introduce

Product name and model

Intelligent OLED display, model：：SW102

Product Introduction

Minimalist design, process without
Super contrast 1.3 -inch monochromatic OLED screen
Excellent outdoor design with
Micro USB serial communication
Bluetooth function is optional, without screw assembly inch monochromatic OLED screen with IP65 waterproof serial communication port, convenient for maintenance services Bluetooth function is optional, which adapt for mobile phone APP maintenance services

Range of application

Suitable for electric power-assist bicycle in accordance with the standard of EN15194

Appearance and size

The material of the product shell is ABS + PC And the material of the window is 2.5D tempered glass 2.5D tempered glass.

Display coding rules

As shown in the above picture, C1 is the manufacture factory code
1701 is the manufacture year, and week number
A means the hardware version
001 is the firmware version number
0001 is the product serial number

Product manual

Specifications

Power supply： DC 24V/36V/48V
Rated current：12mA
Shutdown leakage current：<1uA
Screen specification：1.3” OLED（64*128 dots)
communication method： UART（default）
Operating temperature：-20°C ~ 60
Storage temperature：-30°C ~ 80º C
Waterproof level： IP65

Functional overview

Four buttons, easy to operate
Use password to turn on
Km / miles
Speed display: Real-time speed time speed（SPEED）、maximum speed（MAX）、average speed AVG）
Five stalls of power assist control control：0-4level (OFF-ECO-TOUR-SPORT-TURBO TURBO）
Six levels of electricity instructions：1-5level power，and under-voltage prompt, and provide and under-voltage prompts, and provide
Headlight indicator: Headlight on/off status indication (need information from the controller)
Mileage display: Subtotal mileage: Subtotal mileage (TRIP), total mileage (ODO)
Riding time （TRIP TIME）display
UART communication port Micro USB），convenient for system maintenance and parameter setting
6km/h walk assist function
Error code indication

Installation

Open the display lock clip, set the display in the left handlebar (standard handlebarsize:Φ22.2). Adjust to a position easy to operate tighten and fix the screw by M3 hexagon torque: 0.8N.m.*Note: Damage caused by excessive torque is not covered by the warranty
a display connected with the controller by 5 pin connector as required drawings.

Interface

Boot interface（Can be custom customized as required）

Boot interface, 2seconds show when turning on the display

Basic interface

power assist level and walk mode: 0-4 files assist level, power from low to high are: OFF, ECO, TOUR, SPORT. TURBO, and WALK mode.:
current speed and unit show the current riding speed.
Subtotal mileage and unit: accurate to one after the decimal point, maximum is 999.9:
power indicator show 1-5 level power and under voltage. Then icon blinks when under voltage.
Headlight show when the headlight is on.

Function interface（I）

riding time shows ride duration. The rest information is the same as the basic interface.

Function interface（II）

average speed（AVG） show the average speed of the riding
maximum speed（MAX） show the maximum speed of the riding；
total mileage ODO shows the mileage of the whole riding, maximum is 9999km.
The rest information is the same as the basic interface.

Setting interface

setting interface prompt current interface is for setting
exit item and select bar: select short press the function to exit the setting interface to return to the basic interface; [ ] select menu:
Unit Settings: unit settings of speed and mileage
wheel diameter information: wheel diameter information adapt for the display
This password setting: users can change the password or shut down (turn off the defaulted password function)
Automatic shutdown, after 5 minutes(the default) no operation on the display, it will shut down automatically.
speed limitation information: The allowed maximum speed information of the bike
battery information: The information about the battery
hardware information: The information about the hardware
reset: Reset to factory settings

Definition of buttons

Turn on/off：，Function button： M ，Adjust button+：，Adjust button

Operation

Turn on/off

Maintain the normal connection between the display and the controller. Long press (2 seconds)0 button when is display is off. The display shows the boot interface and enters the basic interface to start work. Long press (2 seconds) the O button when the display is on. Display closed. If no operation to the display and the speed is 0 for 5 minutes, the display will turn off automatically.

Assist mode select

Press or select the assist mode and change the assist power mode. There are 5 odes:OFF/ECOiTOUR/SPORTiTURBO. Default ECO mode when display turned on. OFF means no assist power. (assist mode select as below picture)

Display information switch

Information switches from trip miles, riding time, average speed, max speed, total mileage by short press M when the display is on. It shows loop from trip miles (TRIP) ->riding time (TRIP TIME)-) average speed (AVG), maximum speed (MAX), total mileage (ODO). Mode switch as below pictures:

Walk assist mode

Long press button for 2 seconds, bike entered walk assist mode. When is shown, a loose button to exit walk assist mode? Walk assist mode switch as below pictures (only in the walk assist status):

Headlight on/off

Long press button for 1-second the headlight is turned on（need support of controller ）.Headlight
the icon shows on the interface. Long press the button for 1 second again, the headlight is turned off.
The icon of the headlight is off.

Power indicator

When the battery works normally, the battery power shows 5 levels according to the battery capacity. When the battery power reaches the under-voltage warning value, only the frame of the battery icon is displayed and flash to remind the user to charge immediately. The battery power is shown below:

Percentage of battery power（C）and power level table

User settings

Setting items: unit, turn on password, wheel diameter, •speed limitation information, battery information, time period of automatically shut down, *system information, reset to factory setting. ( • means fixed items, do not provide user settings options)

Enter setting status

10 seconds within display turned on, long press M ( 3seconds ) , system enter the data setting interface. On this status, users can set and view the parameters of the display.
Long press M (3 seconds) to exit and save the setting status. Select [Exit] on the setting interface, short press M to exit, and save the setting status.
User settings interface state, if 10 seconds without the operation, the display returns to normal riding state, do not save the parameter settings.
On data setting state, short press / to switch setting items
Short press M to switch setting items circularly.

Unit setting

Presse / ” to select a setting item in unit setting interface. Press ( short ) M in exit file to return setting interface. Short press M in KM/Mile file to switch KM, Mile unit. Km: The unit of trip mileage and total mileage is Km. The unit of current speed, average speed; maximum speed is KM/H. Mile: The unit of trip mileage and total mileage is Mile. The unit of current speed, average speed, and maximum speed is MPH.

On/off password setting

Enter on/off password setting, press / to select setting item. Switch to Switch to OFF/ON item, short press M to select OFF/ON, to turn on or turn off the password on/off function; Choose ON to turn on the on/off password function and set the password; a short press M to switch password bit from left to right, short press left to right, short press / to adjust the code value. Choose Exit (after save) to return the previous level after setting.
Interface show as below：
Boot again, you need to use a new password to boot, or the display will automatically shut down after 25s.

Wheel diameter information

In-wheel information interface,26 inches means the current display is set for the bike of 26inch wheel diameter. Return to the setting interface by the short press.
Wheel diameter value can be set:16inch, 18inch, 20inch. 22inch, 24inch, 26inch. 700C, 28inch. 29inch
The interface is shown as below:

Speed limitation information

Speed limitation information indicates the maximum speed allowed in the current system (only show the changes through the serial port) Default allowed maximum speed: 25KM/H Interface shown as below:

Battery information

Return selling interface in battery information interface by short press.
BAT %: battery power:
BAT V: battery voltage: Charge: numbers of charge cycles. the interface is shown as below:

Automatic shutdown time

Press / to choose automatic shutdown time (default 5 minutes) in auto-off the interface. Press M to save and return the setting interface.
The interface is shown as below:

System information

Press M to return to the setting interface in the system information interface.
S/N： device ID；
FW Ver： Firmware version number
HW Ver： Hardware version number
The interface is shown as below

Reset

Reset, press / to choose a setting, switch to YES item, short press M to restart the display. The parameter reset to the factory state. Press Exit to exit the page and return to the previous level. The interface is shown as below:

Data clearance

10 seconds after the display is turned on, long press M (3 seconds ). enter the data clearance interface. short pass M pop up the confirmation window, press / to choose an item, short press M again to clearance trip mileage(TRIP). riding time(TRIP TIME), average speed(AVG) and maximum speed(MAX), and return to operation interface. The display will return to the riding interface without data clearance if no operation in 5 seconds.

Normal shutdown and power ower-down will not make the above data clear.

Error information

The display can alert the bike failure, code. failure, if failure is detected, the display interface is shown as below:

Error code definition
Error code table:

Error code	Fault description	Checking method
04 shown at speed	throttle doesn’t turn back to zero position	Check if the

Wire definition

Table 1 wires definition

No.	Color	Function
1	Red(VCC)	VCC
2	Blue(Kp)	Power control wire of the controller
3	Black (GND)	GND of display
4	Green(RX)	Data receive of the display
5	Yellow(TX)	Data transmit of the display

Note

In the use of the display, pay attention to the security, do not plug the power is on.
Try to avoid use exposure in harsh environments like heavy rain, heavy snow, and strong sunlight.
When the display can’t be used normally it should be sent to repair as soon as possible.