TENNANT i-Mop XL Plus User Manual

i-mop XL Plus
Auto scrubber for hard floor surfaces
User Manual
Model Part No.: 1251236

For parts manual and other language operator manuals, visit:
http://www.tennantco.com/manuals

Preface

Thank you for choosing the i-mop® XL Plus, the auto scrubber that cleans faster, cleaner, safer, greener, and is better for everyone. The i-mop XL Plus’s compact design allows you to clean right to the edge and under obstacles, minimizing manual scrubbing. The battery-operated i-mop XL Plus is equipped with two counter-rotating brushes that provide a deep scrub and a great cleaning result. The i-mop XL Plus significantly reduces the amount of water and chemicals needed which both leads to a greener result and reduces the risk of slippery floors.
Please read this manual carefully for important information and operating instructions before using the i-mop XL Plus. Save this manual for future reference. This i-mop XL Plus will provide excellent performance. The best results will be obtained when the i-mop XL Plus is:

• Regularly maintained per the i-mop XL Plus preventive maintenance instructions in this manual.
• Operated with reasonable care and caution.
• Maintained manufacturer-supplied parts.
  When this manual refers to “the manufacturer”, this means Future Cleaning Technologies B.V., an affiliate company of i-team in Eindhoven, the Netherlands. When this manual mentions “the partner”, this refers to your local i-team resell and support service partner.

Purpose of the user manual

The purpose of the user manual is to provide the user with information in such a way that during the life of the i-mop XL Plus the machine is used correctly, efficiently, and safely.
The user manual contains instructions regarding

• Personal operator safety
• Intended and non-intended use of the i-mop XL Plus
• Instructions for daily use
• Maintenance instructions
• Storage conditions
• Disposal of the i-mop XL Plus
  These instructions must be considered to avoid risks that could lead to physical and/or material damage.

Target audience

This user manual is intended for operators of the i-mop XL Plus and their supervisors, as well as partners and importers.

Operators of the i-mop XL Plus

The i-mop XL Plus may only be operated by a person who has correctly read and understood the instructions in this manual or is trained by an experienced operator who has read and understood the instructions in this manual.

Reading guide

The following symbols and terms are used throughout this manual to alert the reader to safety issues and important information:

instructions are not followed, can lead to injuries of the operator or bystanders and light or moderate damage to the product or the environment.
****| CAUTION| Indicates a hazardous situation that, if the safety instructions are not followed, can lead to light and/or moderate damage to the product or the environment.
| ATTENTION| Indicates a liability situation, where the manufacturer or its partners and affiliates cannot be held accountable for damages caused by noncompliance.
| STRONG MAGNET| This indicates the machine contains strong magnets. These can cause pacemakers to stop working or cause electronic data to be damaged, such as information stored on access passes.
| PACEMAKER| Indicates operators and maintenance crew wearing pacemakers should keep a minimum distance of 6 in / 15 cm. In this specific case, operators may not use the machine as a backpack.
| BATTERIES| Indicates a battery-operated machine, batteries must be charged according to the instructions in the separate class I battery charger user manual. Batteries must be disposed of according to your local laws and regulations.
| SLIPPERY  SURFACE| This indicates the machine can cause floors to become slippery. In the workplace, it is advised to place slippery surface signs in these areas.

Introduction

The i-mop® XL Plus is an easy and safe machine to use. This manual helps you to get started and explains the operation and maintenance procedure. You will be pleasantly surprised by the fast and effective use of the battery-operated i-mop XL Plus. The batteries used in the mop XL Plus are the same as a variety of battery-powered i-team products. The batteries must be fully charged before use. Please refer to the user manual of the class I battery charger for the correct procedure. This manual is intended for those who work with the i-mop XL Plus and/or perform daily maintenance. The manual must be read in full before the first actions. This manual describes the correct method of use, safety measures, maintenance, and transport. The manufacturer continuously improves all its products based on user experience and feedback. Any deviations between the texts and/or images from the manual and your i-mop XL Plus can therefore arise from the difference in model or from possible changes due to continuous development and innovation.

Intended use of the product

The i-mop XL Plus is a specialized machine for scrubbing indoor hard floor surfaces. You can use the i-mop with water-based
detergents that have been rated for use within general floor scrubbers.
The fluid tank and brushes come in color-coded versions (blue, green, red, yellow). All three items are easily replaced. This allows you to use different cleaning solutions. For instance, when you move from the food preparing area to the restaurant. ALWAYS use the same color for the fluid tank, brush, and squeegee.

Non-intended use of the product

WARNING
Non-intended use can have consequences for the safety of operators and bystanders and will void the warranty on the product.

• NEVER operate the i-mop® XL Plus near flammable dust, liquids or vapors.
• NEVER operate the i-mop XL Plus when flammable or poisonous liquids like gasoline, oil, acids, or other volatile substances are on the floor.
• DO NOT fill the i-mop XL Plus with any flammable detergent. ONLY use water-based cleaning solutions.
• DO NOT use water that exceeds 113° F/45° C. Using water above this temperature will void the tank warranty.
• DO NOT use cleaning solutions with pH below 3 or above 11 in order to prevent damage to sensitive components.
• DO NOT use the i-mop XL Plus outdoors or on uneven surfaces.
• DO NOT operate this i-mop XL Plus over electrical floor outlets in order to avoid electrical shock.
• NO RIDERS! Do not carry passengers on top of the i-mop XL Plus.
• DO NOT use the i-mop XL Plus as a stepladder or platform.
• DO NOT store the i-mop XL Plus outside in order to avoid damage to electronic components.
• ONLY use manufacturer-supplied parts for maintenance.
• KEEP AWAY from vulnerable people, including children! The i-mop XL Plus is a professional cleaning machine to be used by trained adults only.

Lifespan

Each i-mop XL Plus is guaranteed to operate for at least 2000 hours. The wear on brushes and squeegee heavily depends on the roughness of the surface. They need to be checked regularly.
CAUTION
To ensure proper and safe operation throughout the life of the i-mop XL Plus, the machine must be checked every 500 hours by an authorized i-mop service partner.

Modifications

It is not permitted to make modifications to the design of the i-mop XL Plus without consultation and permission from the manufacturer. This affects the warranty, refer to section 1.6 of this manual.

Specifications

Product size:| 120 x 48 x 46 cm | 47.25″ x 19″ x 18″
---|---
Product size in park position:| 120 x 48 x 36 cm | 47.25″ x 19″ x 14″
Weight (including batteries):| 22.5 kg | 49.6 lbs
Li-ion battery:| DC (25.2V, 9Ah, 222Wh)
Battery capacity:| 2 batteries
Operation time of batteries:| 60 min
Brush pressure:| 31.5 gr / cm 2 | 0.45 psi
Brush speed:| 350 RPM
Detergent tank capacity:| 4 L | 1.05 gallons
Recovery tank capacity:| 6 L / 4 L recommended max | 1.5 / 1.05 gal.
Vibration: Amplitude| Amplitude (mm): <0.4442 Velocity (m/s): <0.008
Acceleration (m/s²): 0.943
Noise level (1m):| 79.6 Db
Theoretical performance:| Up to 1800 m2 per hour| 19,375 sq. ft.
Practical performance:| 1000 – 1300 m2 per hour| 10,764 – 13,993 sq. ft.
Castor wheels:| YES
Power cut off at park position:| YES
Angle power cut off:| YES < 32°
Floating ball for recovery tank:| YES
Timer:| NO

Warranty

The i-mop® XL Plus should be used as intended and described in this manual. Using the mop XL Plus outside will void the warranty on the product.

Identification

The ID tag (figure 3), containing the serial number, can be found on the bottom of the mop scrub deck, between the two brushes.

Description

The compact i-mop® XL Plus consists of two main parts:

• The body contains the motor, cleaning solution tank, recovery tanks, handle with triggers, and control panel.
• The scrub deck contains the brushes and squeegee.
  The i-mop XL Plus can be folded into a park position; this is recommended for storage.
  The i-mop XL Plus consists of:

Legend

1. Trigger
2. Control panel
3. Batteries
4. Scrub deck
5. Recovery tank| 6. Vacuum hose
7. Rotating brushes
8. Squeegee
9. Solution tank
---|---

Safety

Safety comes first. Therefore, please take your time to read and understand these safety instructions. Improper use can cause harm or void the manufacturer’s warranty.

General safety instructions

Sweep before scrub
Remove objects from the floor that can be propelled by or get caught in the rotating brushes.

Brush condition

Make sure to check the condition of the brush before use. Change the brush only when the machine is turned off in a park position.

Machine orientation

Always keep the body of the i-mop® XL Plus in an upright position when cleaning fluid or batteries are inserted.

Strong magnets

CAUTION
Please be aware of the integrated magnets that hold the fluid tanks in place.
WARNING
Operators and maintenance crew wearing pacemakers should keep a minimum distance of 6 in/15 cm.

Batteries

Always use the automatic battery charger provided by the manufacturer.
CAUTION
During normal operation, the 24V batteries cause no safety hazards on their own.
Please keep the following safety instructions regarding the batteries in mind:

• Do not crush, pierce or damage in any way.
• Do not heat or incinerate.
• Do not short circuit.
• Do not dismantle.
• Keep dry.
• Only charge between 5° C~40° C / 41° F~104° F.
• Only use between 5° C~45° C / 41° F~113° F.

Risks during operation

Dress safely
Do not wear a necktie, scarf, or any loose or dangling clothing or jewelry while operating the imop® XL Plus. These can tangle in rotating parts, causing serious injury or death.
Mark the job site
The i-mop XL Plus is designed to leave a dry floor without slippery patches, no additional drying is required. When running the i-mop XL Plus with the vacuum function OFF please mark the job site with a wet floor marker.

CAUTION
The i-mop when used in a mode with water recovery engaged, leaves the floor immediately dry and safe to walk on. Please refer to local law or company policy about the use of a wet floor marker during cleaning.

Careful when parking

Do not park the i-mop XL Plus on ramps or slopes. Always park the i-mop XL Plus on a level, hard surface.

Risks after the operation

Remove battery packs
It is best practice to remove the batteries before executing any cleaning or maintenance task, or before storage.
Machine orientation
Always keep the body of the i-mop XL Plus in an upright (park) position when replacing brushes or squeegees.

Transport and storage

General

CAUTION
Always keep the body of the i-mop® XL Plus in an upright position when filling the cleaning solution tank or inserting the batteries.

Before storage or transport, drain the machine and remove the batteries after each use. It Is best to recharge the batteries before storing them.

Park position

The park position is the upright vertical position for storage and maintenance tasks.

1. Make sure the vacuum hose (Figure 5, pos 2) is pushed back into the machine so it cannot get squeezed.
2. Crouch down and hold the handle (Figure 5, pos 1) with one hand while holding the scrub deck (Figure 5, pos 3) with your other hand.
3. Lift the scrub deck slowly until it stands upright on the front wheels (Figure 5, pos 4). Guide the body towards the scrub deck until it snaps into a resting position.

Transport outside

When outside:

1. Put the i-mop® XL Plus in park position (refer to section 4.2).
2. Carry the i-mop XL Plus with one hand while holding the handle (Figure 6, pos 1) with your other hand.

CAUTION
The transport wheels are not designed to roll over dirty surfaces and sand can cause the wheels to block.

Transport in a vehicle

The preferred way to transport your i-mop® XL Plus is in an upright position and safely secured.

1. Make sure both tanks are empty.
2. Put the i-mop XL Plus in park position (refer to section 4.2).
3. Remove the batteries.
4. Lift the i-mop XL Plus into the vehicle.
5. Secure the i-mop, using a tension belt or another appropriate restraint (Figure 7, pos 1).

As the i-mop XL Plus is a compact machine, it fits in the trunk of your car. Before loading the map XL Plus into your vehicle, make sure both tanks and battery packs are removed.

1. Put the i-mop XL Plus in park position (refer to section 4.2).
2. Remove the batteries and both tanks and pack them separately for transport.
3.  Lift the i-mop XL Plus into your vehicle. Don’t forget the tanks and batteries.
4. Prevent the i-mop XL Plus from moving around during transport by using a tension belt or another appropriate restraint.

CAUTION
The seal of the solution and recovery tank can be damaged during transport in a horizontal position. Make sure you remove them before loading the machine into your car. improper use will void the warranty.

Assembly and installation

The i-mop® XL Plus does not require much assembly. Most importantly, you will have to attach the brushes and squeegee.

Unboxing

The i-mop XL Plus body is packed in a single box. The battery and charger are delivered in a separate box and can be ordered separately.

Legend

1. 1x i-mop XL Plus main body
2. 2x batteries
3. 1x battery charger
4. 1x battery charger manual
5. 1x power cord| 6. 1x squeegee assembly
7. 2x brushes
8. 1x cleaning solution tank
9. 1x recovery tank
10. 1x User manual
---|---

Assembly

Charge the batteries
Before first-time use, charge the batteries according to the instructions in the battery charger manual, so they are fully charged. Make sure the battery packs are charged monthly.
Attach the brushes

To attach the brushes:

1. Put the i-mop® XL Plus in park position (refer to section 4.2).
2.  Hold the scrub deck firmly with one hand.
3. Align the left brush (Figure 9, pos 1) with the left motor disk (Figure 9, pos 2). Align the latches and cut-outs in the brush and motor disk.
4. Push the brush on the motor disk.
5. Turn the left brush clockwise until you see the motor disk turning. The brush is now in place.
6. Align the right brush with the right motor disk. Align the latches and cut-outs in the brush and motor disk.
7. Push the brush on the motor disk.
8. Turn the right brush anticlockwise until you see the motor disk turning. The brush is now in place.

Attach the squeegee

To attach the squeegee:

1. Take the vacuum hose (Figure 10, pos 1).
2. Insert the hose connector (Figure 10, pos 2) in the squeegee (Figure 10, pos 3).
3. Twist the hose connector 1/4 turn for a firm fit (Figure 10, pos 2).
4. Carefully pull the vacuum hose back into the machine.
5.  Hold the scrub deck firmly with one hand.
6. Align the pins on the scrub deck (Figure 10, pos 4) with the holes on the squeegee (Figure 10, pos 5).
7. Push the left side of the squeegee in place.
8. Push the right side of the squeegee in place.

Install recovery tank

1. Put the bottom of the recovery tank (Figure 11, pos 1 and pos 3) on the front of the i-mop® XL Plus.
2. Push the top of the tank into place until you hear a “click” sound, the magnet (Figure 11, pos 2) will lock the recovery tank into place.

Install cleaning solution tank

1. Put the tank (Figure 12, pos 1) on the i-mop® XL Plus with the valve first.
2. Press the tank downward on the nipple to break the valve seal.
3. Push the tank into place until you hear a “click”.

Operation

Before you start

Check the brushes and squeegee for wear and tear (refer to section 7 on maintenance).
Insert the batteries

Best to use a set of batteries that are fully charged before operating the i-mop.

1. Push the blue-coded battery (Figure 13, pos 2) in the blue battery slot. A click signals the battery is locked in place (Figure 13, pos 1).
2. Push the gray-coded battery in the gray battery slot. A click signals the battery is locked in place.
3. During operation, the battery indicators (Figure 13, pos 3) on the control panel show the amount of power left.

ATTENTION
Before you start using the i-mop for the first time, make sure that you have read and understood chapter 10.2: i-mop Plus Automatic Shutoff System.

Fill the cleaning solution tank

1.  Remove the stopper.
2. Pour in a maximum of 1 gal/ 4 L of cleaning fluid.
3. Replace the stopper and make sure it seals tight.
4. Put the i-mop® XL Plus in park position (refer to section 4.2).
5. Put the tank on the i-mop XL Plus with the valve first (Figure 14, pos 1).
6. Press the tank downward to break the valve seal.
7. Push the tank into place until you hear a “click”.
8. Even when wearing gloves, clean your hands afterward.

Operation procedure

Walking to the job site

To move the i-mop® XL Plus from one location to another one in a building:

1. Put the i-mop XL Plus in park position (refer to section 4.2).
2. Hold the handle with one hand (Figure 15, pos 1).
3. Walk slowly and pay extra attention if you pull the i-mop XL Plus over obstacles.
4. To lift the i-mop XL Plus over obstacles, always use two hands.

• Hold the handle with one hand.
• Lift the scrub deck with the other hand.

At the job site

1. Crouch down while holding the scrub deck firmly with one hand (Figure 16, pos 2).
2. Push the handle forward with your other hand (Figure 16, pos 1).
3. Bring the scrub deck slowly down to the floor.

**WARNING**
Never push down the scrub deck with your foot.

ATTENTION
Unlike previous generations of i-mop, the i-mop XL Plus will only power on when the scrub deck is lowered on the floor. When parked in its upright position, the i-mop XL Plus will remain completely powered off to avoid unwanted battery discharge.
4. Stand behind the i-mop® XL Plus.
5. Choose your cleaning mode via the main switch (Figure 17, pos 7). This will also turn on the i-mop XL Plus.

• MODE 1: Brush + water/cleaning solution (Figure 17, pos 1).
• MODE 2: Brush only (Figure 17, pos 2).
• MODE 3: Brush + vacuum (Figure 17, pos 3).
• MODE 4: Brush + water/cleaning solution + vacuum (Figure 17, pos 4).
  6. Hold the handle with both hands.
  7. Squeeze the trigger on the handle (Figure 17, pos 9).
  8. Once the trigger is squeezed the i-mop XL Plus will move forward.
  9. Walk behind the i-mop XL Plus.
  10. Steer by gently turning the handle left or right to move the scrub deck (Figure 17, pos 10).

TTIP: Learn to swivel
operating the i–mop XL Plus is very intuitive and like steering a bicycle. The i-mop XL Plus iis designed to move forward. To turn, stop walking and use your inside hand (the hand in the direction you want to go to) to turn the handle. The i-mop XL Plus can swivel 360 degrees making it possible to reverse direction.

11. Releasing the trigger (Figure 17, pos 9) will immediately stop the i-mop XL Plus. The vacuum motor will stop after 3 seconds.

WARNING
Operating below a 32-degree angle will trigger the i-mop to temporarily shut off its functions to avoid water going into the vacuum motor chamber.
ECO mode
The ECO mode will use 40% less cleaning solution.

1. Turn on the ECO mode by pushing the ECO button, after you have selected your cleaning mode. (Figure 19, pos 1).

Turn off ECO mode by pushing the ECO mode again.

Angle warning indicator

The angle warning indicator is situated on the control panel (Figure 20, pos 1). When the angle of the machine is below 32 degrees,  the indicator light will turn on and the water recovery function will be paused. When the handle is raised above 32 degrees the vac motor will restart after 5 seconds.

Turn off the i-mop® XL Plus

1. Use the i-mop XL Plus main switch (Figure 21, pos 1) and choose MODE 3 Brush + Dry vacuum (Figure 21, pos 2).
2. Operate it about 15-20 feet farther to vacuum the remaining cleaning solution up.
3. Then set the main switch to the “OFF” position.
   Note that the vacuum motor will continue to run for approximately 3 more seconds.

Emptying tanks

Dispose of water or cleaning solution from both tanks in an appropriate drain. Even though the recovery tank is bigger, empty it each time the cleaning solution tank is filled.
WARNING
Please observe the local provisions regarding solution disposal related to wastewater treatment.

Cleaning and storage

Flush the system
Be sure to flush the tanks out completely. To thoroughly flush out any solution in the lines and valves:

1. Refill solution tank with 0.5 to 1 liter of clean water.
2. Use the i-mop® XL Plus main switch (Figure 22, pos 1) and choose MODE 4 Brush + Water/Cleaning solution + Dry vacuum (Figure 22, pos 2).

Cleaning the tanks

At least before storing the machine you need to clean the i-mop tanks, especially the recovery tank.

1. Dispose of water or cleaning solution from both tanks in an appropriate drain.

2. To clean the recovery tank thoroughly:
   Partially fill the tank with fresh water and hold it horizontally with the holes facing up.
   Tilt the tank repeatedly, thoroughly rinsing all the dirt and debris out from the tank.

3. To clean the solution tank, follow the same procedure.
   TTIP: Dry the tanks
   Oppen both tank caps before storage to allow the tanks to dry.

Removing battery packs

1. Put the i-mop XL Plus in park position (refer to section 4.2).
2. Hold the i-mop XL Plus by the scrub deck to stabilize.
3. While pressing both plastic pins inwards (Figure 23, pos 1), pull each battery pack away (Figure 23, pos 2).
4. When the i-mop XL Plus isn’t used regularly, store the charged battery packs in a dry, clean place.
5. Make sure the battery packs are charged monthly.

Check the brushes and squeegee

1.  Check to see if both brushes are clean and intact, refer to section 7.1 on how to remove
   them.
   Clean them under freshwater or replace them if necessary.
   Replace brushes if the yellow wear indicator is the same height as other bristles.

2. Check to see if the squeegee is clean and intact, refer to section 7.2.1 on how to remove it.
   Clean it with fresh water and wipe it with a clean, damp cloth.
   Replace the squeegee blades when necessary.

Store in an upright position

1. Please ensure that the i-mop® XL Plus is parked in a place where nobody can bump into it.
2. Put the i-mop XL Plus in park position (refer to section 4.2).
3. Store the i-mop XL Plus close to a wall (Figure 24, pos 1) with the handle pointing towards the wall and the brushes facing away from the wall.

ATTENTION
Unlike previous generations of i-mop, the i-mop XL Plus will only power on when the scrub deck is lowered on the floor. When parked in its upright position, the i-mop XL Plus will remain completely powered off to avoid unwanted battery discharge.

Maintenance

 Brush replacement

The brushes come in pairs and wear out over time. Replace when the yellow brush indicator strip is at the same height as the other bristles.

The brushes are attached to the scrub deck via a bayonet fitting.

1. Put the i-mop® XL Plus in park position (refer to section 4.2).
2. Hold the scrub deck firmly with one hand.
3. Use your other hand to turn the left brush anticlockwise (Figure 25, pos 1) until you feel resistance or see the motor disk turning as well.
4. Pull the brush off the motor disk toward you.
5. Turn the right brush clockwise until you feel resistance or see the motor disk turning as well.
6. Pull the brush off the motor disk toward you.
7. Visually inspect the motor disks.
8. Clean the i-mop XL Plus scrub deck with a clean, dry cloth before you install the brushes.

Squeegee replacement

The squeegee blades come in pairs and wear out over time. When you notice the floor is no longer being dried properly, replace the squeegee blades.

Detach the squeegee

1. Put the i-mop® XL Plus in the park (refer to section 4.2).
2. Hold the scrub deck firmly with one hand.
3. Pull-on the left side of the squeegee to remove it (Figure 26, pos 1).
4. Pull-on the right side of the squeegee to remove it (Figure 26, pos 2).
5. Remove the vacuum hose from the squeegee by twisting the hose.

Flip/replace the squeegee blade

1. Unscrew the 8 plastic nuts on the back.

2. Take off the squeegee rear plate.

3. Once the plastic part is removed, you can easily take off the rear rubber blade.

4. Push the 8 screws through the front blade in order to remove the squeegee front plate.

5. Take off the rear rubber blade.

6. Inspect the front and rear rubber blades:
   The first time: flip the blades so the top of the blade is now facing the floor. Push the front plate screws through the holes.
   The second time: attach a new set of blades. Push the front plate screws through the holes.
   CAUTION
   The special squeegee blades that contain small arrow-like shapes cannot be switched. These need to be replaced every time.

7. Put back the plastic rear plate.

8. Screw the 8 plastic nuts on the back.

Attach the squeegee

To attach the squeegee:

1. Take the vacuum hose (Figure 27, pos 1).
2. Insert the hose connector (Figure 27, pos 2) in the squeegee (Figure 27, pos 3).
3. Twist the hose connector 1/4 turn for a firm fit (Figure 27, pos 2).
4. Carefully pull the vacuum hose back into the machine.
5. Hold the scrub deck firmly with one hand.
6. Align the pins on the scrub deck (Figure 27, pos 4) with the holes on the squeegee (Figure 27, pos 5).
7. Push the left side of the squeegee in place.
8. Push the right side of the squeegee in place.

Replace vacuum hose

1. Detach the squeegee as described in 7.2.1.
2. Remove the solution tank. You can see where the vacuum hose is connected at the imop® XL Plus handle.
3. Hold the scrub deck firmly with one hand.
4. Detach the vacuum hose by twisting the connector 1/4 turn anticlockwise.
5. Now you can carefully pull the vacuum hose from the top of the machine.
6. Guide the new vacuum hose via the opening to the hose connector located at the i-mop XL Plus handle.
7. Connect the top to the hose connector by twisting the clockwise 1 /4 turn until they have lined up.
8. Reinstall the squeegee.

Cleaning the recovery tank and the ball float shutoff assembly

To clean the recovery tank and ball float shutoff assembly, you have to remove the floating tank from the i-mop® XL Plus.

1. Pull the top of the recovery tank outwards (Figure 28, pos 1).

2. Lift the recovery tank up and move it away from the body of the i-mop® XL Plus (Figure 11, pos 2). Figure 28

3. Grab the support frame of the ball float shutoff assembly (Figure 29, pos 1)  between your index finger and your thumb and pull it outwards. Taking apart the ball float shutoff.

4. Pull the support frame (Figure 30, pos 2) out of the rubber housing (Figure 30, pos 3).
   To do this, bend the rubber flaps (Figure 30, pos 1) outwards to release the 4 nocks of the support frame.

5. Pull the float ball housing (Figure 30, pos 4) out of the rubber housing. To do this, bent the rubber ring (Figure 30, pos 5) outwards to release the 4 nocks of the float ball housing.

6. The floating ball (Figure 30, pos 6) comes out.

7. Rinse the parts with tap water. If required, clean with a brush (Figure 31,  pos 1). Assembling the ball float shutoff.

8. Place the floating ball in the float ball housing (Figure 32, pos 1).

9.  Press the float ball housing (Figure 32, pos 4) into the rubber housing (Figure 32, pos 3). Make sure that the 4 nocks of the float ball housing fit into the holes in the rubber ring (Figure 32, pos 5).

10. Press the support frame (Figure 32, pos 2) in the rubber housing (Figure 32, pos 3). Make sure that the 4 nocks fit into the holes of the rubber housing.

11. Fill the recovery tank with approximately 1 liter of tap water (Figure 33, pos 1).

12.  Carefully shake it and dispose of the wastewater properly.

13. Place the ball float shutoff assembly back in the recovery tank, see Figure 29. Make sure that the support frame and rubber housing sit flush on the tank and seal it.

14. Put the bottom of the recovery tank (Figure 34, pos 1 and pos 3) on the front of the i-mop® XL Plus.

15. Push the top of the tank into place until you hear a “click” sound, the magnet (Figure 34, pos 2) will lock the recovery tank into place.

Recommended additional cleaning

Clean the exterior of the i-mop XL Plus weekly with a non-abrasive, non- solvent cleaner or a clean, damp cloth. To clean the scrub deck, remove the brushes first.

Recommended service time

It is recommended to schedule a full service by one of our service partners every 500 hours.

Accessories

The i-mop® XL Plus can be equipped with different brushes and polishing pads. The use of these accessories is only allowed by experienced and trained operators as some polishing pads can be abrasive and can cause damage to the floor surface when applied incorrectly. For more information please contact our sales department or the partner who provided the i-mop XXL Plus.

Troubleshooting

control panel
Eco mode on| Check the ECO mode light on the control panel
Empty tank| Fill the tank
Tank incorrectly placed| The tank valve must be clicked on the nipple to open the seal, replace the tank
Filter blocked| Ensure the solution tank has no dirt particles and the filter is clean
Blocked water pipe| Request for service
Poor water recovery| Squeegee opening blocked| Remove the pipe and clean the squeegee opening
Tears in squeegee blades| Replace squeegee blades
Recovery tank ball float assembly

blocked

| Check the ball float shutoff assembly and clean if necessary
Vacuum hose blocked| Check and remove the blockage
Vacuum pump not running| Request for service
Leakage| Tanks incorrectly placed| Check and reattach fluid tanks

                    Tear in the vacuum hose

| Replace vacuum hose or request for service
Battery not charging| The battery is at end of life| Replace battery

Decommissioning and disposal

ATTENTION
It is the responsibility of the i-mop® XL Plus owner to dispose of the product responsibly.

After decommissioning, the i-mop XL Plus still contains valuable resources and needs to be disposed of according to your local laws and regulations regarding the recycling of electrical equipment.

Before disposal please:

1. Flush the machine (refer to section 6.3.1).

2.  Remove the batteries for separate disposal (refer to section 6.3.3).
   TIP:
   Alternatively, keep the batteries for use in another piece of I–team equipment.

3. Remove all loose components like brushes, tanks, and squeegees.

4. Dispose of all items according to your local laws and regulations.

Attachments

i-mop Plus Automatic Shutoff Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>