Swann Wireless Doorbell Kit DC835MP3 Instruction Manual

Swann Wireless Doorbell Kit DC835MP3 Instruction Manual

PRODUCT OVERVIEW

Speaker unit

Doorbell unit

INSTALLATION

Speaker
No wiring is necessary. Just plug the Speaker into an easily accessible power outlet and switch the power outlet on.

Doorbell
The Doorbell is powered by one “A23” battery which comes preinstalled.
To activate the battery, simply pull the plastic tab out from the side of the Doorbell unit.

Replacing the Battery
Battery replacement is necessary as soon as the LED indicator stops lighting up when the Doorbell button is pressed. To replace the battery, insert a small flathead screwdriver into the small notch at the base and lift the front cover off, as shown on the right. Replace with a battery of the same type (A23) only. Make sure the new battery is installed according to the polarity markings (+ and -) shown in the battery holder.

Mounting the Doorbell

You can mount the Doorbell using the supplied double-sided adhesive tape or screws.

• For tape mounting, make sure the surface is dry, smooth and free of dust and other substances that could affect adhesion.
• For screw mounting, open the Doorbell with a screwdriver and separate the front cover from the rear cover (as previously described in “Replacing the Battery”). With the “UP” arrow pointing up, penetrate the two standby holes on the rear cover with two screws, and screw the rear cover to the mounting surface. Clip the front cover back onto the mounted rear cover. Make sure the rubber seal around the edge of the rear cover is seated properly.

Note: Avoid mounting the Doorbell on metal surfaces, including UPVC doorframes, as this may reduce the transmission range.

MELODY SELECTION & PAIRING

You can personalize the melody played on the Speaker when the Doorbell button is pressed. To select a melody on the Speaker and pair it with the Doorbell:

1. Press the Previous or Next Melody Select button repeatedly on the Speaker to cycle through the available sounds (including your recorded custom melody. To learn how to record your custom melody, see “Recording your Custom Melody”). Stop when you hear something you like.
2. Press and hold the Volume button on the Speaker for about 5 seconds, until a quick tone is heard and the LED indicator starts blinking. The Speaker is now in pairing mode.
3. Within 5 seconds, press the Doorbell button. The Speaker will confirm pairing by playing the selected melody with the LED indicator blinking while the melody is playing. If pairing is not completed within 5 seconds, a quick tone is heard and the LED indicator goes off. In this case, you will need to repeat steps 2-3 to try pairing again.
4. At any time, you can change the melody. Simply repeat the steps above each time you want another melody selected.

RECORDING YOUR CUSTOM MELODY

You have the option of recording your own custom melody (up to 40 seconds long) with your favourite tune on the Speaker directly from your mobile device or computer.

1. Plug one end of the supplied 3.5mm audio cable into the AUX jack on the Speaker and the opposite end into the headphone jack on your mobile device or computer.
2. Open your favourite music app on your connected device. Find the track that you want to record and get it ready (for example, skip to your favourite parts of the track) for playback. When music is played, you will be able to hear it through the Speaker. Use the Volume buttons on your connected device to directly control the volume (recording level) of the music coming through the Speaker.
3. To start recording your custom melody, press any button on the Speaker  once. The Speaker will beep and its LED indicator will turn solid blue indicating the Speaker is recording now.
4. Now start playback of the track on your connected device.
5. The Speaker automatically stops recording at 40 seconds or you can stop recording at any time before that by pressing the “Pause” button in the music app. The Speaker will double-beep to indicate it has stopped recording and then replay the music recorded from your connected device automatically. If the recording ended automatically, you need to stop music playback on your connected device so that you can listen to the recording through the Speaker.
6. If you want to re-record your custom melody, simply repeat steps 3-5.
7. Once you are done recording your custom melody, unplug the audio cable from the Speaker and connected device.
8. To select your custom melody on the Speaker and pair it with the Doorbell, follow the steps described in “Melody Selection and Pairing”.

ADJUSTING THE SPEAKER VOLUME

The volume of the Speaker is adjustable. Simply press the Volume button until the desired volume level is obtained. You will hear the difference in volume each time the Volume button is pressed.

RESETTING THE SPEAKER

You can reset the pairing information on the Speaker. Simply press and hold the Next Melody Select button on the Speaker until a quick tone is heard and the LED indicator blinks once.

Have Questions?

We’re here to help! Visit our Support Center at support.swann.com You can also email us at any time via: tech@swann.com

Limited Warranty Terms & Conditions

Swann Communications warrants this product against defects in workmanship and material for a period of one (1) year from its original purchase date. You must present your receipt as proof of date of purchase for warranty validation. Any unit which proves defective during the stated period will be repaired without charge for parts or labour or replaced at the sole discretion of Swann. The end user is responsible for all freight charges incurred to send the product to Swann’s repair centres. The end user is responsible for all shipping costs incurred when shipping from and to any country other than the country of origin.

The warranty does not cover any incidental, accidental or consequential damages arising from the use of or the inability to use this product. Any costs associated with the fitting or removal of this product by a tradesman or other person or any other costs associated with its use are the responsibility of the end user. This warranty applies to the original purchaser of the product only and is not transferable to any third party. Unauthorized end user or third party modifications to any component or evidence of misuse or abuse of the device will render all warranties void.

By law some countries do not allow limitations on certain exclusions in this warranty. Where applicable by local laws, regulations and legal rights will take precedence.

For Australia: Our goods come with guarantees which cannot be excluded under Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to major failure.

Battery Warnings

• Do not dismantle, open or shred secondary cells or batteries.
• Do not expose cells or batteries to heat or fire. Avoid storage in direct sunlight.
• Do not short-circuit a cell or a battery. Do not store cells or batteries haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal objects.
• Do not remove a cell or battery from its original packaging until required for use.
• Do not subject cells or batteries to mechanical shock.
• In the event of a cell leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
• Do not use any charger other than that specifically provided for use with the equipment.
• Observe the plus (+) and minus (–) marks on the cell, battery and equipment and ensure correct use.
• Do not use any cell or battery which is not designed for use with the equipment.
• Do not mix cells of different manufacturer, capacity, size or type within a device.
• Keep cells and batteries out of the reach of children.
• Seek medical advice immediately if a cell or a battery has been swallowed.
• Always purchase the correct cell or battery for the equipment.
• Keep cells and batteries clean and dry.
• Wipe the cell or battery terminals with a clean dry cloth if they become dirty.
• Secondary cells and batteries need to be charged before use. Always use the correct charger and refer to the manufacturer’s instructions or equipment manual for proper charging instructions.
• Do not leave a battery on prolonged charge when not in use.
• After extended periods of storage, it may be necessary to charge and discharge the cells or batteries several times to obtain maximum performance.
• Secondary cells and batteries give their best performance when they are operated at normal room temperature (20 °C ± 5 °C).
• Retain the original product literature for future reference.
• Use only the cell or battery in the application for which it was intended.
• When possible, remove the battery from the equipment when not in use.
• Dispose of properly.
• The socket-outlet shall be easily accessible.
• CAUTION: Risk of explosion if the battery is replaced by an incorrect type

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>