iiglo Wi-Fi Smart Plug User Manual

Wi-Fi Smart Plug

User Manual

Notice

1. Please check if there is damage existed. If yes, please contact us for replacement.
2. A secured 2.4 GHz WiFi network is required for the Smart Plug to work. If you open SG network at the same time, pis kindly close the SG firstly
3. When you connect the plug with your WIFI and mobile device, please keep them near the router for getting the stronger signal.
4. The total power of the connected appliances could NOT be bigger than the maximum power of the smart plug.
5. Please make sure your appliance is in the “ON” condition when you want to control it with the Smart Plug.
6. Please keep the smart plugin a good and safe use condition.
7. Please do NOT disassemble the smart plug to avoid the security risks.

smartphone. (Quick Mode)
Slowly flashing blue| Smart Plug has created a network that needs to be connected by your phone. (AP Mode)
Flashing red| Your Smart Plug has turned to another mode.
Solid red| Smart Plug is connected to a Wi-Fi network and power on.
Light off| Smart Plug is connected to a Wi-Fi network but power off.
Note :| After the configuration, if the indicator of the plug flashes blue slowly, the smart plug may be in the “lost connection” condition.
Please check the condition of your router.

Reset: Press the ON/OFF button for 6 seconds to recover the factory setting.

Add Device

Download Smart Life App

Please scan the QR code, or input Smart Life to download on App Store or Google Play.

Registration and login in

Attention:
There’s no registration code needed if email method chosen.

Add Device

1. Click the icon “+” on the top right corner of “My Home” page, or the “Add Device” button.
2. Enter into the next page “Select Device Type”, and click the “All” button.
3. Choose the “Electrical Outlet” and then follow the instruction of the page to finish the connection.

Mode Introduction

1. Quick Mode Configuration (Common)
   In this mode, the indicator light blinks blue rapidly (twice per second). If it blinks blue slowly (once every 3 seconds), press and hold the power button on the Smart Plug for 6 seconds until the indica­tor light blinks rapidly.

2. AP Mode Configuration
   In this mode, the indicator light blinks blue slowly (once every 3 seconds). If it blinks blue rapidly (twice per second), press and hold the power button on the Smart Plug for 6 seconds until the indicator light blinks slowly.
   

Note: When you choose the AP mode, the Smart Plug will create a network, whose name is “smartlife – XXXX(numbers)”. Please connect this network with your phone.

The way to Connect Smart Plug to Amazon Alexa or Google Home

Step 1. Please click the “…” button in the upper right corner.
Step 2. Get the button of Alexa and Google. Please click the button which you want to connect.
Step 3. According to the corresponding guidance, establish the connection between Alexa or Google Home and the Smart Plug.

FAQ

1. What should I do when the device configuration process has failed?
   You could:
   1.1 Check whether the Smart Plug is powered on or not.
   1.2 Check whether your mobile device is connected to 2.4G WIFI network.
   1.3 Check your network connectivity. Make sure the router is working properly:
   1.3.1 If the router is dual-band router, select 2.4G network and then add Smart Plug.
   1.3.2 Enable the router’s broadcasting function.
   1.3.3 Configure the encryption method as WPA2-PSK and authorization type as AES or set both as auto.
   1.3.4 Wireless mode cannot be 11n only.
   1.3.5 Check whether there are too many WIFI signals near the plug.
   1.3.6 Check whether the router connected devices reach the amount limit. Please try to turn off some devices’ WIFI function and configure Smart Plug again.
   1.3.7 Check if router’s wireless MAC filtering function is enabled. Remove the device from filter list and make sure the router allows the connection with the Smart Plug.
   1.4 Make sure the password of your WIFI network entered in App is corrected when you add Smart Plug.
   1.5 Make sure the Smart Plug is in ready for App-Config: the indicator light is quickly blinking blue (twice per second) for quick mode configuration, slowly blinking blue (once every 3 seconds) for AP mode configuration.
   1.6 Repeat the App-Config process.
   1.7 Factory reset the Smart Plug and try to add it again.

2. Can I control the Smart Plug through a 2G/3G/4G cellular network?
   The Smart Plug and the mobile device are required to be under the same WIFI network(2.4G) when you add the Smart Plug for the first time. After successful device configuration, you can remotely control the device through a 2G/3G/4G cellular network.

3. How can I share my device with family?
   Open the App, go to “My home” page > click the button of the device you have connected > click the “••• ” button in the right upper of the page > find the “Share devices” in the “Other” part. Now you can share the device with added family members.

Imported by iiglo
Ostre KuHerod 4, N-3241 Sandefjord, Norway
www.iiglo.com I Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>