Oceanic WATER SYSTEMS RO5150E Reverse Osmosis Water Filtration System Owner’s Manual

Oceanic WATER SYSTEMS RO5150E Reverse Osmosis Water Filtration System Owner’s Manual

It contains useful information on how to maintain and care for your Reverse Osmosis water filter system.

Please read and become familiar with instructions and parts needed before proceeding with the installation.

BEFORE INSTALLATION: Inspect the system

Please take the system and all the components out of the box. Inspect the system and all the connection fittings carefully, make sure nothing is damaged during shipping. If any part is cracked or broken, please do not proceed with the installation and contact us for an exchange or diagnosis.

Recommended tools list:

• Variable speed drill
• Drill bit: 1/4” (for the waste line), 1/8” (as pilot, not mandatory), and 1/2” (for standard faucet hole, air-gap faucet requires 1&1/4” hole)
• 5/8”, 9/16” open-end wrench, or adjustable wrench, pliers
• Phillips screwdriver
• Utility knife, or scissors
• Teflon tape

Operating Parameter

• Operating pressure: 85psi maximum
• Feed water temperature: 40 – 100 degree F (4-37 degree C)
• Do not connect this unit to hot water source
• Install the RO in a sheltered environment, avoid exposure to hot and cold weather or under direct sun light.

General Installation/Operation/Maintenance Requirements

• Installation needs to comply with state and local laws and regulations.
• System must be installed indoor away from possible environmental damage
• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts.
• This reverse osmosis system contains a replaceable treatment component critical for effective reduction of total dissolved solids. The product water shall be tested periodically to verify that system is performing satisfactorily.

Components included with the RO system

Make sure you have all these parts before starting installation.

• 1 RO system head with pre installed membrane
  

• 3 Pre-filters in 3 Housings
  

• 1 Storage tank
  

Installation kit includes

• 1 Faucet with washers and nuts
  

• 1 Feed water adaptor 3/8”- 1/2” with needle valve kit
  

• 1 Drain saddle for waste water
  

• 3 Color tubing 1/4”
  

• 1 Tank’s Ball Valve

• 2 Wrenches for opening filter and Membrane housing
  

• 1 Faucet Adapter

Component Itemization

1. Sediment pre-filter and housing (1st -stage filter)
2. Carbon block pre-filter and housing ( 2nd -stage filter)
3. Carbon block pre-filter and housing ( 3rd -stage filter)
4. Membrane and housing (4th -stage filter)
5. In-line carbon filter (5th -stage filter)
6. Storage tank
7. Tank ball valve
8. ASO – Automatic Shut Off valve
9. Check valve (Internal check valve encased in plastic fitting)
10. T-fitting
11. Feed water inlet
12. Product (filtered) water outlet
13. Bracket

Fitting Types: There are 2 types of fittings provided for connecting the system

1. Quick-Connect (QC) fitting: (no insert, sleeve, or nut) Most of the fittings on the RO unit are this
   How to Connect:

   • See Fig.1. Push the tubing into the Quick-Connect fitting, then gently pull back on the tubing to make sure connection was secure.
     
     Fig. 1

   • No inserts, sleeve, or nuts are needed to secure the connection.

   • No Teflon tape!
     To Disconnect:

   • See Fig.1A. Push in and hold down on the collet ring square against the fitting. With the collet held in this position the tube can be removed.
     
     Fig. 1A

2. Metal compression nut fitting: (comes with 1 insert, 1 sleeve, 1 nut) Only feed water adapter-needle valve is this type.
   Important! Use plastic sleeve and inserts on the plastic tubing we provide. Do Not use metal sleeve or insert on plastic tubing or the connection will leak!
   How to connect:

3. See Fig.1B. Slide the compression nut onto the tubing.
   
   Fig.1B

4. Slide the plastic sleeve onto the tubing.

5. Insert the “insert” into the tubing.

6. Insert the tubing into the opening of the fitting.

7. Slide the brass nut up, then tighten nut with a wrench. No Teflon tape! (An extra metal sleeve is provided in case you need to connect your own metal tubing. Use Teflon tape if connecting metal tubing.)

Space: Make sure there is sufficient space under the counter for install lotion (an area of about 17″L x 6″W x 18″H for the system, 11″D x 18″H for tank).

The RO system is best installed under the kitchen sink. But if that is not feasible you can install the system anywhere where there is a cold water supply with sufficient water pressure for the chosen RO model, and an outlet to drain off the waste water from the system.

Mounting: No need to mount the RO system on the wall. The RO system can stand in the sink cabinet without mounting, this makes future filter change easy and convenient. If you prefer to mount the system to the wall, please make sure it con be token down easily for filter replacement.

Feed Water: RO systems are designed to treat both hard and soft water and can handle incoming MS levels up to 2000ppm.

Step 1: Feed Water Connection

The RO system must be connected to the COLD water supply only!

1. Locate the Cold water supply valve under the kitchen sink (the round or oblong handIe on the right side). Turn on the incoming cold water completely by turning the shut off handIe clockwise.
   Note: I( the cold water shut off valve can not turn off the water, the main water supply to the house must be shut off for the installation. Another option is to use a “self piercing saddIe vaIve“ from APEC or from a local hardware store.

2. Feed Water Adaptor (1/2” to 3/8“): See Fig. 5. The Feed Water Adaptor comes with a separate Needle Valve. The Adaptor goes inline onto your 1/2” or 3/8” cold water pipe. The Needle Valve portion screws onto the Adaptor as shown in Fig. 5A.
   
   Fig. 5
   a. I /2” x 3/8’ Male-Female Water Supply Adapter with 0-ring.
   b. 1/2” x 3/8” Male-Female Converter with 0-ring.
   c. 1/4” x 1/8” Male NeedIe Valve.
   Fig. 5A – Needle Valve Installation.
   Attach the needle valve (C) to water supply adapter (A). Please apply 5-6 wraps often(Ion tape to needIe valve prior to connecting it to the water supply adapter (A).
   
   Fig. 5B – If your pipe has a 1/2” Connection.
   By attaching the 1/2” x 3/8” converter (B) to the Male end of the water supply adapter (A), you now have a 1/2’ Male and Female water supply adapter.
   
   Fig. 5C – If your pipe has a 3/8” Connection.
   By afiaching the 1/2” x 3/8” converter (B) to the Female end of the water supply adapter (A), you now have a 3/8” Male and Female water supply adapter.
   

3. Recommend Connection For Flex Line Riser: See Fig.6A. & Fig. 6D. Loosen nut and separate cold water riser tube from faucet shank. Gently bend riser tube so that the Feed Water Adapter (Fig 5) fits onto the faucet shank. If your riser tube has no built-in washer, then fit the cone-shaped washer provided onto the riser tube. Connect the riser tube, the feed water adapter, and faucet shank together and tighten.
   For Solid Copper Riser: See Fig.6B. Follow the same procedure as for flex line. If the copper riser cannot bend, then it’s best to replace it with a flex line riser. Then fit the feed water adaptor the same way as described above.
   Option Connection Point: See Fig. 6E. The feed water adapter can also be installed between the riser tube and faucet shank. Loosen nut and separate cold water riser tube from faucet shank. Gently bend riser tube so thot the Feed Water Adapter fits onto the faucet shank. If your riser tube has no built-in washer, then fit the cone-shaped washer provided onto the riser tube. Connect the riser tube, feed water adapter, and faucet shank together and tighten.
   
   Needle Valve Connection
   
   Fig. 6C
   
   Fig. 6D
   
   Fig. 6E

4. Needle Valve : See Fig. 6C. Screw the Needle Valve onto the Adaptor tightly. Apply 6-8 rounds of Teflon tape onto Needle Valve be(ore attaching it to the Adaptor.

To open needle valve: Turn needle handle counter-clockwise.
To close needle valve: Turn needle handle clockwise.

Test for leaks at this point : Close the Needle Valve (turn needle handle clockwise all the way in to close) Turn ON the cold water supply to the sink faucet. If the Needle Valve or the Adaptor leaks, check the connection and try applying more Teflon tape or tighten the brass nut some more to stop the leak.

Step 2: Drain Saddle Installation

Note: To avoid annoying drainage noise, mount drain line as low as possible on the vertical toilpiece, or on horizontal toilpiece.

There is constant water pressure “packed” inside the RO system which blocks the waste water from backing-up into the system. So the waste water is “forced-drained”, not “gravity-drained”

1. See Fig.7. The drain saddle assembly should be installed above the trap and on the vertical or horizontal tailpiece . To reduce the drainage noise, mount the drain line as low as possible above the trap, or on the horizontal tailpiece.
   
   Fig. 7

2. See Fig.8. Mark the position of the hole on the drain pipe and drill a 1/4“ hole through one side of the drain pipe . There is a piece of self-adhesive sponge provided. Glue this sponge to the inside of the saddle, this will cushion any gap between the saddle and the pipe. Make sure the hole on the sponge is thoroughly punched out, and is aligned to the hole on the saddle
   
   Fig. 8

3. See Fig.9, 9A. Make sure to align the drain saddle hole to the drilled hole perfectly. Misaligning these two holes will block the waste water and cause membrane damage. Attach the drain saddle to the drain pipe and tighten the two screws evenly.
   
   Fig. 9
   
   Fig. 9A

Step 3: Drill A Hole For The RO Faucet

Drill 1/2” diameter hole for standard RO faucet. (Air-Gap faucet: drill 1&1/4” hole.)

For best results use a 1/2“ corbide-tipped masonry drill bit.

Wear safety glosses to protect your eyes while drilling the faucet hole.

Note: No need to drill a hole if on existing hole is available:

• Spore hole: If there is a spore hole in the sink covered by a chrome cover, simply remove the chrome cover and install the RO faucet there.
• Spray hose: If the spray hose is not in use, remove the hose, and mount the RO faucet there. Remember to plug up the outlet under the main faucet. If the spray hose uses a diverter at the base of the spout, be sure to remove it to avoid trouble later on.
• Hanging faucet: If drilling a hole is not feasible (i.e. rental home, drill tool not available etc.), the faucet con just on the cabinet door or wherever that is convenient. Be creative!

When drilling a hole for the RO faucet, choose a location that looks good, works well, and is most convenient for dispensing pure water. An ample flat area is required (or the (aucet base so that the (aucet can be drawn down tightly.

1. Faucet location: Make sure the (aucet stud will be accessible from below when the Role is drilled. If space is not available on the upper sink area, the faucet can be located on the counter top by the edge of the sink. If the counter top is ceramic tile, the method for drilling the hole will be the same as for porcelain sinks.
2. For Stainless Steel Sink: Before using a 1/2” carbide drill bit, an indent should be made with a center punch to keep the drill bit from walking. A small pilot hole will also aid the drill bit.
3. For Porcelain Sink: Porcelain enameled sinks can readily be chipped if care is not exercised when drilling the hole. Before starting the drill motor, apply firm downward pressure on the bit until a crunching occurs. This will help keep the drill bit from walking when starting the hole. A small pilot hole will also aid the drill bit.

Note: Immediately after the hole drilling is done, clean up all metal chips, as metal chips will stain the porcelain!!

Step 4: Mounting The Faucet

1. Mount the (aucet as shown in Fig.10.
   
   Fig. 10

2. Attach threaded end of faucet adapter to the faucet metal stem. Note(Ion tape needed here.

3. Connect the Clear line to the faucet.

4. The faucet has a solid metal handle that controls the flow of purified water exiting the faucet. Turn the handle to horizontal position to release the water and vertically to shut off.

Step 5: Positioning The System

1. Main System: The main system can stand in the sink cabinet. No need to mount the system to the wall. If you prefer to mount the system to the wall, please make sure it can be taken down easily for filter replacement.
2. Tank: The storage tank can also lay on its side if needed. The tank works fine in this position. If the tank cannot fit under the kitchen sink, it can be placed elsewhere up to 20 feet away from the RO system without much pressure loss.

Step 6: Connecting The System

Summary of Tubing Connections:

There ore 4 connections: See Fig 11 and 11A

• Point A to X : Connect RO to COLD water supply — Red tubing.
• Point G to Y: Connect product water from 5″-stage filter to tank — Yellow tubing. This tubing is a 2-way line, Product water enters and leaves the tank via this line.
• Point H to Z : Connect product water from 5’h -stage output to RO faucet — Clear tubing.

Drain line to W: Connect waste water from 4″-stage membrane to drain outlet — Block tubing.

Please Note: The diagram below is for our Non Pump RO-45, RO-90 and RO- PH90. If you are installing the RO Perm or RO Pump, please refer to the diagram in the addendum

Fig 11

Fig 11A

To ensure a smooth and correct installation, please connect the water lines following the sequence and order outlined below. Refer to Fig.11 & 11A for proper point locations.

Details on Tubing Connections:

1. Point Z Faucet connection:
   Tubing color : Fitting type: White tubing. Connect the WHITE tubing to the base of the RO faucet. Quick Connect Fitting. Simply push White tubing into Quick Connect fitting. No Insert, Sleeve or Nut needed here. (Attach threaded end of faucet adapter to the faucet metal stem. No Teflon tape needed here)

2. Point X Feed water connection:
   Red tubing. Connect the RED tubing to the Feed Water Needle Valve.
   Metal compression nut fitting. See Fig.1B on page 4. Use plastic sleeve. Add “insert” to tubing. No teflon tape here. Tighten nut with wrench.
   TIPS: If Point X leaks after you have tightened the brass nut, check to make sure you did put the plastic “insert and sleeve” onto the tubing. If the insert is already in place, then try applying Teflon tape from the threaded metal stud all the way to the plastic tubing, wrap the whole connection with 8-10 rounds of Teflon tape. Smooth out the tape on the threaded part with your fingers. Tighten brass nut again. This should stop the leak.
   If the plastic sleeve is damaged, you can use the metal sleeve, but you need to apply Teflon tape as described above, this should stop the leak.

3. Point W Waste water connection:
   Black tubing. Connect the BLACK tubing from the RO to the Drain Saddle. Quick- Connect fitting on drain saddle. No teflon tape.
   Do Not add ”insert” into Black tubing. Simply push tubing into port.

4. Point A: System water inlet (to Stage 1 prefilter) connection:
   Red tubing. Connect the RED tubing from the Feed Water Valve to the RO’s stage -1 prefilter.

5. Point H: Stage-5 filtered water to faucet connection:
   White tubing. Connect the White tubing from the faucet base stud to the Stage-5 filter’s outflow end at point H. (See “Flow –>” arrow on the filter for flow direction.)

6. Point G: Stage-5 filter’s T-fitting connection:
   Yellow tubing. Connect the YELLOW tubing to Stage-5 filter’s T fitting. Quick Connect fitting See Fig.1. Simply push the Yellow tubing into the 5th stage filter’s T Fitting. No
   Inserts, Sleeves or Nuts are needed to secure the connection. No Teflon tape needed here.

7. Point Y: Tank’s input & output connection:
   See Fig.12. Apply 6-8 wraps of Teflon tape to tank’s threaded Output stem on top of tank (remove rubber cap if there is one). Screw tank Valve onto Output stem.
   Yellow tubing. Connect the YELLOW tubing from Stage-5 T-fitting to the tank’s valve. Quick-Connect fitting on ball valve. Simply push Yellow tubing into valve port.

The 4 gallon tank comes pre charged at 5 psi, 14 gallon tank at 7 psi.

Standard 4-Gallon Tank Diagram

Tank Ball valve

Option: Ice maker Connection

If you want to conned product water from the RO to your ice-maker, you will need:

• One T-fitting, preferably the quick-connect type fining
• Extra 1/4 ” tubing long enough to go from the RO system to your ice-maker
• Optional: One shut-off valve, preferably the quick-connect type.

See Fig.13. Before connecting the product water line from Point Z to H, add a T-fitting near point H to divert product water to both the ice-maker and the faucet. It is best open the line to the ice maker after the first tank has been discarded and the 2nd tank has completely filled.

Using RO for Ice-maker only:

If you want the RO to feed your ice-maker (fridge) only, you should still connect the RO faucet as a 2nd outlet. This allows you to drain the tank, flush new filters through the faucet rather than through your icemaker line. You can hang the faucet by the system and not mount it.

Option: Multiple Outputs – Add Shut Off Valv e:

If your RO is feeding several output points (icemaker, fridge, bathroom), you should add a Shut-Off valve to each output line (except the RO spigot line). This way, if you ever need to diagnose a problem in the system, you con easily shut off these lines to isolate the water flow for accurate troubleshooting.

Step 7: System Start-Up

1. Turn on feed water : Slowly, turn on your Cold water supply. Turn on the Needle Valve (turn counter-clockwise) to allow the raw water to enter the system. Check for leaks!
2. Turn on tank valve: Turn on the tank’s ball valve to allow water to enter the tank. The tank’s valve is ”On” when the valve handle is parallel (in the same direction) with the valve’s outlet (see Fig.12). Check for leaks!
3. Wait for tank to fill: Before usage, allow the tank to fill. Tank normally takes 2-3 hours to fill. When the tank is filled, the RO will shut off automatically.
4. Drain Tank: Do not use the first tank of water! Drain it out to flush the system and new filters. Lift the faucet lever up into a locked position to drain tank. Let the tank refill again and the pure water is ready for use.
5. Clean up area: Allow the system to run while cleaning up fools and work area.
6. Check for leaks! Make sure no leaking at joints, fittings, valves, and tubing connections.

Congratulations! You hove successfully installed the Reverse Osmosis System!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>