REWYRE SY-W0290 UV Disinfection Lamp Wireless Charger User Manual
- June 6, 2024
- REWYRE
Table of Contents
REWYRE SY-W0290 UV Disinfection Lamp Wireless Charger
Function Buttons
How to use
Step 1.
- Connect the power adapter to any wall outlet and plug it into the device using the included USB cable.
- The LED displays will turn on to indicate the product is powered and ready for use.
BATTERY BACKUP
Your clock has a pre-installed battery backup that will keep the time in case power is interrupted (like by a power outage, for example). If you notice that battery backup is no longer working, simply replace the CR2032 coin-cell battery in the battery compartment on the right side of the clock. Pull the compartment out to access the CR2032 battery.
Step 2. Setting the Time
- Press the “Alarm” button once to enter minute setting, and adjust the minute by pressing +/-.
- Press the “Alarm” button once more to enter hour setting, and adjust the hour by pressing +/-.
- Press the “Alarm” button a third time to complete time setting.
Note:
Double click Alarm button to setup 12-hour time system and 24-hour time
system. AM and PM will display while 12-hour time system is set.
Step 3. Setting the Alarm
- Press and hold “+” for 3 seconds to activate or deactivate Alarm 1, and press and hold “-” for 3 seconds to Activate or deactivate Alarm 2.
- While either alarm is activated, press and hold the “Alarm” button for 3 seconds to adjust the minute by pressing +/-.
- Press the “Alarm” button once more to adjust the hour by pressing +/-.
- Press the “Alarm” button a third time to complete Alarm setting.
Step 4. Using the Alarm
- The alarm sounds for 3 minutes when activated.
- Touch any button to Snooze the alarm. It will ring for 3 more times after 5 minutes snoozing. The indicator flashes and Alarm button is out of function during the Snooze Mode. If you’ve set two alarms, long press “+” to stop Alarm 1 and “-” to stop Alarm 2. All buttons will function normally;
Step 5. Setting the Display Brightness
You can go through these brightness settings manually by pressing “+” or “-”
on the front of the clock.
To increase display brightness: Press”+” on the front of the clock. Each
press goes to the next settingminimum, second, third, max, and off.
To decrease display brightness: Press”-” on the front of the clock.
Step 6. Wireless Charging
IMPORTANT: Before you try to charge your device, make sure it is
compatible with wireless charging. If your device has a metal case, remove it
before you put the device on the charger.
1. Place your wireless charging-compatible device directly onto the charging
pad on top of the clock. Refer to the placement illustrations here as a guide.
The charging indicator in front of the charging pad turns blue while your
device is charging. It turns off when your device has finished charging. Check
your device’s screen to see the progress of charging. You can remove your
device at any time during charging.
Important: If the charging indicator light starts blinking, there’s
something interfering with the charging. Make sure there are no objects
between your phone and the charging pad. You might need to remove your phone’s
case to charge wirelessly.
Note:
Indicator Display:
Power connection successful - blue light flashes once
Standby - light off
Charging -solid blue light on
Charged - light off
FOD - blue light flashes continuously
**Top
**
Wireless charging pad and indicator
lets you charge compatible devices wirelessly when the clock is using AC
power. The indicator turns solid blue when your device is charged and turns
off when your device is charged. The charging indicator blinks when there is a
problem charging.
Back
USB-C power jack plugs into the provided charging cable to power the
clock.
USB charging port provides wired charging for your USB device.
2. When your device is completely charged, remove it from the charging pad.
Step 7. For Disinfecting
- Place your smartphone or other item to be disinfected into the box.
- Press the “Lamp” button to begin disinfecting mode, the alarm will sound for 5 seconds after the UV lamp counts down for 1 minute.
- Press and hold “Lamp” button for 3 seconds to turn on the UV disinfection lamp, the UV lamp will work for 15 minutes, the alarm will sound for 5 seconds when disinfection time is up.
- Support the function of Hall element: When the clock body and the base magnet are closed, the UV lamp works; When the clock body and the base magnet are separated, regardless of whether the disinfection command is completed, the UV lamp needs to stop working immediately, the countdown ends and the light indicator turns off;
- Anti-mistouch “Setup” button design: When the clock body and the base magnet are separated, all the buttons have no setup function in the first 30 seconds, and the function is restored after 30 seconds; When the clock body and the base magnet are closed, other buttons except the “Lamp” button do not function for 3 seconds, and the function is restored after 3 seconds.
Attention:
- In order to function alarm, wireless charging, UV disinfection and USB output all together, power shall be connected by a QC2.0 or QC3.0 adapters. If connected by a 5V adapter, only wireless charging and alarm can work together.
- Do not squeeze or collide.
- Do not disassemble or put into the fire, water, to avoid short-circuit leakage.
- Do not use wireless chargers in severe high temperature, humidity or corrosive environments to avoid leakage of damaged circuits.
- Do not place too close to magnetic cards (ID cards, bank cards, etc.) with magnetic strips or chips to avoid magnetic card failure.
- Keep more than 20cm between the implanted medical device (pacemaker, implantable cochlea, etc.) and the wireless charger to avoid potential disruption to medical devices.
- Keep children from the product in case they play the wireless charger as a toy to avoid accidents.
- Keep the wireless charger and receiver device away from water and other liquids.
- To clean the charger, make sure the power supply is disconnected.
- Usage temperature: 0-45.
- Usage humidity: 20-85% (40)
- Pictures in this manual are all illustration. Final product is subject to fact.
- Inside package: alarm charger, charging cable, manual.
- power adapter is not included. Please purchase separately or use phone original adapter.
Specification
Input: 5V/2A, 9V/2A
Outputpower: 10W (MAX)
Charging efficiency: 73%
Charging distance: 8mm
Frequency: 110-205KHz
Size: 145x116x73mm
Applicable Devices
Products qualified with Qi standard.