Acepen AP906 9.5 Inch Electric Writing Tablet User Guide

**Acepen AP906 9.5 Inch Electric Writing Tablet User Guide

**

Overview

Notes: The shortcut key function can be customized, which needs to be set in the driver. (You need to install the driver by yourself if needed.)
The P02 pen can be stored in the cloth label.
Connect the mobile phone to switch shortcut keys. (You can select the shortcut keys from K1 to K8.)

System Requirements
Windows 7 or above
Mac OSX 10.11 or above
Android  6.0 or above

Product and Accessories

1. AP906

2. P02 Pen

3. USB Cable
   

4. Replacement Nibs x 8
   

5. Nib Clip

6. Gloves

7. OTG Adapter (Type-C & Micro USB)

8. Quick Start Guide

Graphic Tablet Installation

1. Connect the Type-C end to the connecting port on your AP906.
2. Connect the USB end of the USB cable to your computer interface.
   

OTG Adapter

1. Connect the Type-C end to the connecting port on your AP906.
2. Connect the USB end of the USB cable to the OTG adapter and then connect it to the Android phone or tablet. (Please select the OTG interface corresponding to connecting port of the phone or tablet interface).

Driver Installation

Before Installation

1. Before installation, if there are drivers of similar digital products, please uninstall them firstly, including drivers of older versions of Acepen.
2. Before installation, please shut down all painting-designed software and anti-virus software. Avoiding unnecessary errors during the installation process

Installation

(No installation required to connect to Android phone/ tablet)

1. Please download the driver from the following website: www.ace-pen.com/support.
2. When installing the driver, please follow the prompts and choose to restart the computer after installation.

Driver Function Introduction

Note: After installing the driver and connecting the product with your computer, the figure shown above will be displayed on the screen of the computer.

Note: Click “Pen”, the above figure will be displayed. You can switch Pen Mode to Mouse Mode, which means you can draw with the pen or operate it as a mouse. And you can set the pressure as you like based on the right part of the figure. The more you select the value in the right corner of the chart, the less sensitive the pen will be, which means you may need to put more strength when using the pen. As for the chart of Pressure Test, you can use it to test for the pressure and select the value as you like.

Note: Turn to “Map”, you will see the figure as above. For the factory setting, the whole panel of the product can be used to control the screen of the computer. But you can change the parameters in the right part of the figure to adjust the area you want to use on the panel to control the screen.

Note: Click “Function”, the above figure will be displayed. You can use the shortcut keys on the keyboard to control the keys K1 to K8 on the product.
The shortcut keys shown in the figure will be as the factory setting, and you can change it as you like with the driver installed.

Replace the Nibs

1. Use the nib clip to pull the nib out of the pen.
2. Replace with a new one and push it into the pen
   
   

Precautions

• Do not place the digital tablet and pressure sensitive pen close to magnetic fields, so as not to interfere with the use of the product.
• Do not place the tablet and pen on an unstable place to prevent it from falling from a height and being damaged.
• Do not place the tablet and pen close to water sources, such as bathtubs, washbasins, kitchen sinks, washing machines, wet basements or poolsides, etc., to prevent liquids from splashing on the tablet and pen.
• Before cleaning the tablet, unplug the USB cable and then wipe it with a soft damp cloth. It is not recommended to use detergent to clean it.
• Do not insert other objects into the USB port or any other openings. If metal objects or other objects are inserted into the port or other openings, it may cause the product to malfunction or burn, or even cause electric shock.
• Do not disassemble the tablet and pen, which may cause overheating, fire, electric shock or other injuries, including personal injury. Meanwhile, disassembling the product will invalidate your warranty.
• Try to store the tablet in places with a constant temperature. Places with the violent alternation of heat and cold will cause the tablet film to foam and affect its use.
• If you have any questions or problems with the  product, which isn’t included in the user guide, please don’t hesitate to contact us.

Problems & solutions

• Why can it move the cursor without pressure sensitivity?
  Please reconfirm whether the driver is correctly installed with the latest version and launched (there is a small icon in the lower right corner of the desktop). If you cannot find the small icon when installing the driver, please check whether it has been disabled by the anti-virus software. Please enter the anti-virus software to release it. If you have installed other drivers for similar products, please uninstall all drivers on your computer, including our drivers, and then download the latest drivers from our website: http://www .ace-pen.com, and then reinstall the driver. If the problem remains after following the above steps, please contact us via email: support2@acepen.com.

• After the driver is launched, why is the product not connected?
  If you cannot use the product, please reconnect the tablet to the USB port of the computer. If the problem remains, please unplug it and reconnect the USB or connect it to another USB port of the computer for testing. You can also try to delete the driver and restart the computer.
  Please check whether the cursor can move normally. If the driver has not been installed, the cursor cannot be moved normally. Please use another computer to test. If it works normally, the original computer driver has failed. Just reinstall the latest driver. If the cursor cannot be moved when testing with another computer, it may be caused by a pen or tablet hardware failure. Please contact us via email: support2@ace-pen.com.

• Why cannot the pen be used to draw and can only move the cursor in Mac OSX?
  Please download the latest driver from the website. After installation, launch the computer “System Preferences”> “Security and Privacy”> “Privacy” and add the downloaded drivers to “Input Monitoring” and “Accessibility” respectively. Please restart the computer after that. If the problem remains, please contact us via email: support2@acepen.com.

Uninstall the Driver

Windows

• Click “ Start ” > “ Control Panel ” > “ Programs ” > “ PenTablet ” > Follow the uninstalling steps until the program is uninstalled.
  Note: Find the following file, if it exists, delete it:
  C:\Windows\System32\Wintab32.dll
  C:\Windows\SysWOW64\Wintab32.dll
  If it prompts that it cannot be deleted because a program is occupied. Please go to the task bar at the bottom of the desktop and right-click to open the task manager. Shut down the program occupying the file through the task manager process. After uninstalling, restart the computer.

• Mac OSX
  Click ” Finder ” > “application” > “ PenTabletDriver ” > “ Uninstall Tablet ” >
  Follow the uninstalling steps until the program is uninstalled.
  Note: Please launch your Activity Monitor to make sure that no relevant driver program is running. Please restart the computer after uninstalling
  

Service Support

If you have any problems, please contact us via our website: www.ace- pen.com or email address: support2@ace- pen.com

Or Visit: https://acepen.afterservice.vip/

Website:www.ace-pen.com
E-mail:support2@ace-pen.com

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INPUT : 100 MA@5V

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>