aqua 28303-7 28 Port LED Side Mount Light Instruction Manual
- June 6, 2024
- Aqua
Table of Contents
Operating Manual for
Navigation Lights Series AQUA SIGNAL 28
| |
---|---|---
| |
Operating Manual for Navigation Lights AQUA SIGNAL LED Series 28
Navigation Lights with LED technology
| Supply: | 12V DC +/-20%. |
|---|---|
| Consumption: | port, starboard, stern: approx 2W each. Bicolour: approx 2W. |
Approvals:
ABYC A-16 & USCG/IMO Colregs (USA) for vessels < 20m (65’) USCG / IMO COLREGS for vessels < 20m (65’) ISO19009 for vessels <20m (65’) Tested by IMANNA Laboratory Inc.
Regulations
For all ships, the rules set forth in Annex 1 to the COLREG’s – Positioning
and Technical Details of Lights and Signalling Shapes – must be adhered to.
The technical data regarding horizontal and vertical positioning and spacing
of the navigation and signaling lights laid down in these mounting
instructions do apply to all ships irrespective of their flag.
Mounting Instructions
The function of the navigation lights can only be assured and be in accordance
with the regulations if the following points are adhered to: For correct
positioning of the navigation lights on board the COLREG’s have to be
followed. The navigation lights must be positioned on and above the keel line
e.g. parallel to it. Their horizontal symmetrical level (A) must be parallel
to the construction water line (CWL). The navigation lights have a directional
arrow that runs parallel to the keel line in the direction of travel. The
light cannot be obstructed by parts of the boat or passengers. Their position
may not be changed while in use. Mounting upside down is not allowed.
Important note for port and starboard lights
(1) In case of screens are used for the sidelights the front screen has to be
removed since it is not necessary and is obstructing the light output in the
right ahead direction.
DESCRIPTIONS
SIDELIGHTS SSb + SBb 28 (2) (4)
Angle: 112,5° green / red visibility 2 nm
STERN light H 28 (2) (3) (4)
Angle: 135° white Visibility 2 nm
BICOLOR SIDELIGHTS TD 28 (3) (6)
Angle: 112,5° red and 112,5° green visibility 2 nm
MOUNTING
Sidelights starboard (SSB), port (SBB), and stern (H) (4)
The housing cap must be removed for assembly. Fasten the previouslcabled
assembly mounting rear panel on the side of the ship with twoscrews. Use
gasket as a template for proper positioning and marking foscrew holes.
a) Horizontal spacing of assembly holes 50 mm.
b) The connection cable can be laid behind the rear panel.
c) Place the housing cap, lettering upwards, corresponding to the “signal zero
direction” (see marking), on the mounting rear panel. Check that the cap is on
firmly.
DEMOUNTING
Sidelights starboard (SSB), port (SBB), and stern (H) (5) For demounting
the housing cap must be removed carefully with an angled screwdriver first on
the aft side and afterward on the zero-ahead side
MOUNTING
Bicolor (TD), Deck Mount Starboard (SSB), and Port (SBB) (6) The
installation can only be done as a top mount and cannot be installed
underneath. You can use the gasket as a template to mark the mounting hole for
the screw (not supplied). Also, mark the location of the hole for wiring.
Drill holes accordingly. Also, use the template to mark the position of the
“stop”.a) Position the navigation light. Make sure signal zero arrow if facing
forward. (see marking) b) For correct alignment of the light, port (red), and
starboard (green), the Marking must always point upwards. The arrow marking on
fixtures must be pointed forward for proper alignment. c) Tighten fastening
screw.
ELECTRICAL INSTALLATION SIDELIGHTS, BICOLOR, SIGNALLING LIGHT All
navigation lights are fitted with cables and ready for use. Only the housing
cover (side lights), respectively the cable cover (bicolor side lights), has
to be removed for mounting. The navigation lights have been tested in
accordance with IEC 60945 and are below the approved threshold values.
However, it cannot be excluded that in exceptional cases it may come to an
interaction between the navigation lights and the radio equipment. Please
ascertain a sufficient distance between the navigation lights, the radio
antennas, and the radio equipment.
MAINTENANCE:
Special care is not necessary. Occasional cleaning of the housing and glass
with a soft brush and freshwater will be sufficient. We recommend cleaning the
transparent cover in regular periods with clear water. Aggressive cleaners
containing solvents should not be used. The LED-Electronic is fitted within a
cast to protect it from dirt and weather. The housing is fitted with air slits
for better acclimatization that cannot be closed.
ATTENTION:
Solvents can destroy the optic of a navigation light. We recommend removing
the light prior to executing paint jobs.
The housing of the light should never be painted for photometric reasons. The
lenses in particular but also, other plastic components may not be touched
with paint.
*SPARE PARTS / ACCESSORIES**
Covers for the sidelights starboard, port, stern. Cable cap for bicolor and
Deck mounting.
Part-no:
| starboard, the stainless steel cover | 9840294600 |
|---|---|
| port, the stainless steel cover | 9840294600 |
| stern, stainless steel cover | 9840294700 |
| bicolor, the stainless steel cover | 9840294800 |
| Deck mounting starboard, | 9840294900 |
| stainless steel Cover | |
| Deck mounting port, | 9840295000 |
| stainless steel Cover | |
| Gasket for housing starboard, | 9840295200 |
| port, stern |
Deck mounting starboard,
Deck mounting port|
Safety instructions:
Beware of optical radiation!
Risk of eye injury. Do not look directly into LED lighting.
Gefahrenhinweis:
Warnung vor optischer Strahlung!
Augenverletzungen möglich. Nicht in die LED-Beleuchtung blicken.
Indication de danger:
Attention au rayonnement optique !
Possibles blessures occulaires. Ne pas regarder en directiment léclairage LED.
Glamox Marine and Offshore GmbH
Linzer Str. 9a, 28359 Bremen Germany
e-mail:
info@productiongermany@glamox.com
Internet: http://www.glamox.com/gmo
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>