aqua barista Water Dispenser User Guide

October 27, 2023
aqua barista

aqua barista Water Dispenser User Guide
aqua barista Water Dispenser

CLEANING AND SANITIZING

Your water dispenser exterior should be thoroughly cleaned at least twice a year, and your SmartFlo™ water cartridge replaced every 12 months. If you do not have a replacement cartridge handy, you can order one here and it will be shipped directly to you. Your replacement kit will include a SmartFlo™ cartridge, bottle adaptor, lid key and plug for the bottle tube:

Before you start cleaning, wash your hands thoroughly with soap and water for at least 20 seconds.

TIP: The best time to replace your water cartridge is when the existing water bottle is empty.

WHAT YOU’LL NEED:

  • SmartFlo™ replacement cartridge
  • 70% rubbing alcohol or disinfecting wipes
  • Clean cloth or soft brush
  • Disposable non-latex gloves
  • Bucket
  • Heat-resistant container to fit under spigots
  • Towels to absorb any water spills

WARNING: Always use caution when handling hot water.

Using Instructions

  1. Slide the cooler door up and turn off the hot tank heater switch (Fig 1). Let the unit stand for one hour before cleaning to allow the hot tank to cool.
    Using Instructions

  2. Remove the empty water bottle (Fig 2). Wipe interior cabinet with 70% rubbing alcohol or disinfecting wipes.
    Using Instructions

  3. Unplug the bottle tube connected to the neck of the water bottle. Plug the bottle tube using the red plug provided in the SmartFlo™ replacement kit (Fig 3).
    Using Instructions

  4. Remove cup holders, if applicable.
    Open the cooler lid using the key provided in the replacement kit (Fig 4).

  5. Close cooler door. Place a glass or other container below the water faucets to  catch any drips.

  6. Remove the SmartFlo™ cartridge and bottle tube by unlatching the blue locking arm and rotating the two blue knobs to the open position (Fig 5).

  7. Pull up on the SmartFlo™ water cartridge (Fig 6). Do not squeeze the water reservoir as water could leak out.

TIP: Have a bucket nearby to dispose of the used SmartFlo™ cartridge and bottle tube, which will contain water.

  1. With the cooler top still open, open the coffee pod holder (Fig. 7).

  2. Remove the coffee cup holder (brown) (Fig 8) and machine wash (top rack only).
    Using Instructions

  3. Turn the red twist locks on each side to release the coffee pod holder. (Fig. 9).

  4. Lift out and machine wash (top rack only) (Fig. 10).

  5. Wearing gloves, feed the new bottle tube through the hole indicated (Fig 11).

  6. Insert the new SmartFlo™ cartridge and secure into place by pressing down (Fig 12).

  7. Rotate the blue knobs to the closed position. Close and latch the blue locking arm (Fig 13).
    Using Instructions

  8. Close the cooler lid by pushing down to lock into place.

  9. Wearing gloves, carefully unpack the new bottle adaptor. Pull the adaptor tube to straighten (Fig 14) and insert it into a new water bottle.

  10. Feed the tube into the water bottle until it reaches the bottom.

  11. Remove the red protective cap from the bottle tube (Fig 15). Install it into the bottle adaptor (Fig 16).
    Using Instructions Using
Instructions

  12. Slide water bottle into the cabinet and close the door.

  13. Clean spigots, bottle receptacle and cabinet with 70% rubbing alcohol or disinfecting wipes. Vacuum or wipe the grill on the back of the dispenser to remove any dust.
    TIP: The cooler exterior should be cleaned every 6 months.

  14. Clean the drip tray and grill by emptying the tray and cleaning the tray and grill with dishwashing soap or by placing them on the top rack of the dishwasher (Fig 17).
    Using Instructions
    TIP: The drip tray and grill should be cleaned monthly.

  15. Wipe down the cooler and the surrounding area to dry any water spills.

  16. Wash your hands thoroughly with soap and water for at least 20 seconds. Install a full water bottle on the dispenser.

  17. Prime the dispenser to fill the reservoir by holding down the cold water spigot for 1 minute, or until water flows continuously. Repeat with the hot water spigot until water flows continuously. Turn on the hot tank switch.

Overview

WARNING: Dispense water through the hot and cold spigots before turning on the hot tank switch. Failure to follow proper installation instructions may cause damage to water dispenser.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals