danalock V3 Danabridge User Guide
- June 6, 2024
- danalock
Table of Contents
Danabridge V3
User Guide
The following instructions are in English. Localized versions can be found with the QR-code below.
Add the Danabridge V3 in the Danalock App
Open the Danalock App and add the Danabridge by selecting ”Add device” in the
menu tab. When the Danabridge has been enrolled you can pair it with your
Danalock V3.
Go to:
Menu > My Accessory Devices > [Danabridge name] > Pairing
Select the lock you want to control with the Danabridge V3.
Connect the Danabridge V3 to wifi
Go to:
Menu > My Accessory Devices > [Danabridge name] > Wifi
Select your access point and enter the credentials. The Danabidge V3 is ready
for use when it has connected successfully.
LED-Signals
The Danabridge V3 indicates the status of several operations with different colors:
LED signal | LED color | Status indication |
---|---|---|
Long white blink | Power on | |
Constant green light | Device is online | |
Constant red light | Device cannot access Wi-Fi | |
Yellow blinking | Device has not been configured | |
Red blinking | Device has no connection to a server | |
Green blinking | Device communicating with a server | |
Constant purple light | Device is ready to update | |
Blue while performing an action | Device is updating |
Configuring the Danabridge V3 with click-commands
You can configure the Danabridge via the button found in the small hole on the
side.
When you get to the setting you want to change, wait for 5 seconds and the
Danabridge will react to your command. If you make the wrong number of clicks,
just stop at a number of clicks where the LED doesn’t light up and wait for 5
seconds. The LED will flash red to indicate that it has timed out.
Clicks | Color | Activity |
---|---|---|
10 | Red | Reset user settings |
This action deletes all user settings on the Danabridge.
Firmware upgrade
Go to:
Menu > My Accessory Devices > [Danabridge name] > Firmware
and press ”Upgrade firmware”. Make sure to keep your phone near the Danabridge
V3 during the entire firmware upgrade process.
Simple Guidelines
Please follow these guidelines when configuring, using, or recycling the DBV3.
Violating these guidelines may be dangerous, illegal, or otherwise
detrimental. Further detailed information is provided in this manual.
Terms of use
This equipment design is primarily for indoor use mounted in a standard
electrical outlet. Use only Danalock approved accessories for the DBV3. Do not
connect incompatible products, and do not operate the DBV3 where wireless
radio communication is prohibited. Like hospitals, buildings near blasting
sites, etc.
Do Not Operate Where Prohibited
Do not allow the DBV3 unit to operate wherever wireless radio communication
use is prohibited or when doing so may cause interference or danger as the
DBV3 cannot be turned off after installation.
Device Operation and human exposure to electromagnetic fields
The DBV3 unit is a low-power radio transmitter and receiver. Periodically the
DBV3 wakes up either due to activity or by a timer. When it is ON, it receives
and sends out radio frequency (RF) signals for a short period of time.
Specific Human Absorption Ratio (SAR)
The DBV3 unit is not intended for handheld use or to be worn on the body. A
minimum separation of eight (8”) inches (20 cm) is to be maintained between
the DBV3 and any persons’ body.
Pacemakers and other Medical Devices
If any other personal medical devices are used in the vicinity of a DBV3 unit,
consult the manufacturers of the medical devices to determine if they are
adequately shielded from external RF energy. Physicians may be able to assist
in obtaining this information.
Interference
Like all wireless devices, the DBV3 may encounter electrical interference that
may affect its performance. The DBV3 is tested and certified according to
international and European standards. The performance hereof ensures correct
operation in the presence of electromagnetic interference and/or electrostatic
discharge.
Category of use
The DBV3 WiFi interface is an accessory to other Danalock products and will
only work together with these to access the internet.
Security for electrical functions
The DBV3 has no indications, sound alarms in case of a connected lock
malfunction.
Security for electrical manipulation
The DBV3 is tested compliance to the EMC requirement laid out in the
2014/53/EU directive. The performance hereof ensures correct operation in the
presence of electromagnetic interference and/or electrostatic discharge.
Children
The DBV3 series and its accessories are not used to solicit data from or
market to children CE mark
The DBV3 complies with the essential requirements of the RED directive
2014/53/EU directive with respect to the radio spectrum, EMC, Health and
safety. EU Certificate and Declaration of conformity (DOC) statements can be
downloaded from the homepage:
https://danalock.com/legal/certificates/
Accessory manufacturer information: Power adaptor
MORE FOREST ELECTRICAL APPLIANCE (HK) CO LTD
Office 3A-9, 12 FI Kaiser Ctr, No 18 Ctr St Sai Yin Pum,
HONG KONG
Product specifications
Supply Voltage | Via USB | 5V DC, 1A |
---|---|---|
Temperature range | Active operating mode | 0°C to +40°C |
Storage | 5°C to +40°C | |
Mechanical specifications | Dimensions (D x H) | 53 mm x 32 mm |
Weight | 36 g | |
Material | Plastic | White ABS |
Radio interfaces | WiFi | Max 12 dBm |
Bluetooth LE | Max 4 dBm |
Warranty
Danalock ApS products are covered by a limited
manufacturer warranty. The Danalock ApS warranty is limited to the warranty
rules and legislation present in each country. The warranty only covers
manufacturing faults. The warranty does not cover misuse, wrong installation
or damage due to a faulty installation or wrong maintenance.
The invoice act as the proof of warranty, so please keep it as a reference for
any warranty complaints.
Qualified Service
The Danabridge V3 contains no user-serviceable or replaceable parts. Non-
functioning units must be returned to an authorized service center for repair
or replacement.
Technical Assistance
If you have a problem and cannot find the information you need in the product
documentation, please contact Danalock ApS at
support@danalock.com. Please have the following
information ready:
- Serial number (preferred), MAC address or alias of the lock
- The username used when registering/installing the lock
- The username used when getting the error (if different username)
- Time of incident
US and Canada certification marks
This device contains radio transmitters that comply with CFR47 part 2.1091,
part 15.207, Part 15.247 of the FCC rules and with RSS-GEN, RSS-102, and
RSS-247 of Industry Canada requirements
Notice statements according to CFR 47 Part 15.19 / RSS-GEN:
The device complies with Part 15 of the FCC rules and with Industry Canada
license-exempt standard(s). Operation is subject to the following two
conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTICE statements according to CFR 47 Part 15.21:
Changes or modifications made to this equipment not expressly approved by
Danalock Apps may void the FCC authorization to operate this equipment.
Statements according to CFR 47 Part 2.1091 and RSS-102: With respect to
radiofrequency radiation exposure Information, it is declared that this
equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20
cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
FCC part 15B note
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Australia and New Zealand
This product complies with the AS/NZS 4268 requirements for Bluetooth LE
transceivers (2402 MHz ~ 2480 MHz ) and WiFi transceivers (IEEE
802.11b/g/n-HT20): 2412MHz ~ 2472MHz.
The product complies with the requirements of the relevant ACMA Standards made
under the Radiocommunications Act 1992 and the Telecommunications Act 1997, by
the Supplier’s Declaration of Conformity (SDOC). These Standards are
referenced in notices made under section 182 of the Radiocommunications Act
and 407 of the Telecommunications Act.
The product complies with the requirements of the relevant standards under
Section 134 (1) (g) of New Zealand Radiocommunications Act 1989, by the
Supplier’s Declaration of Conformity (SDOC)
Japan
The product is approved in Japan with the certificate ID n°:
[R] 204-820373
This device is granted pursuant to the Japanese Radio
Regulatory labeling:
The Danabridge V3 product are regulatory compliant to the following regulation
(Europe, USA/Canada, Japan, Australia/NZ):
204-820373
FCC ID: 2ADSH-DBV3
IC: 12588A-DBV3
References
- Danalock · Danalock V3 - The Smart Home Enabler
- Support · Danalock
- Danalock · Danalock V3 - The Smart Home Enabler
- Certificates · Danalock
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>