GIGABYTE GC-WBAX210 Motherboard Installation Guide

GC- WBAX210
Installation Guide
12WE6-WBAX210-10AR

**Installing the Wi-Fi/Bluetooth Card

**

Step 1
Install the Wi-Fi/Bluetooth card in a PCI Express x1 slot. Connect one end of the USB cable to the USB connector on the Wi-Fi/Bluetooth card.

Step 2
Connect the other end of the USB cable to the F USB connector on the motherboard.

Step 3
Tighten the antenna cables to the antenna connectors on the Wi-Fi/Bluetooth card respectively.

Step 4
Then move the antennas to a place where the signal is good.

Installing the Drivers and Utilities

After the computer starts, install the driver for the Wi-Fi/Bluetooth Card. Adjust your wireless LAN configuration based on your environment after installing the driver.

Regulatory Notices

United States of America, Federal Communications Commission Statement

Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information
Product Name: PCIe add-in card
Trade Name: GIGABYTE
Model Number: GC-WBAX210
Responsible Party – U.S. Contact Information: G.B.T. Inc.
Address: 17358 Railroad street, City Of Industry, CA91748
Tel.: 1-626-854-9338
Internet contact information: https://www.gigabyte.com

FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules, Subpart B, Unintentional Radiators.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radiofrequency (RF) electromagnetic energy emitted by FCC- certified equipment. The Intel PRO/Wireless 5000 LAN products meet the Human Exposure limits found in OET Bulletin 65, 2001, and ANSI/IEEE C95.1, 1992. Proper operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCC’s recommended limits.
The following safety precautions should be observed:

• Do not touch or move the antenna while the unit is transmitting or receiving.
• Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face or eyes while transmitting.
• Do not operate the radio or attempt to transmit data unless the antenna is connected; if not, the radio may be damaged.
• Use in specific environments: – The use of wireless devices in hazardous locations is limited by the constraints posed by the safety directors of such environments. – The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA). – The use of wireless devices in hospitals is restricted to the limits set forth by each hospital.

Antenna use
In order to comply with FCC RF exposure limits, low gain integrated antennas should be located at a minimum distance of 7.9 inches (20 cm) or more from the body of all persons.

Explosive Device Proximity Warning
Warning: Do not operate a portable transmitter (such as a wireless network device) near unshielded blasting caps or in an explosive environment unless the device has been modified to be qualified for such use.

Antenna Warning
The wireless adapter is not designed for use with high-gain antennas.

Use On Aircraft Caution
Caution: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because their signals could interfere with critical aircraft instruments.

Other Wireless Devices
Safety Notices for Other Devices in the Wireless Network: Refer to the documentation supplied with wireless Ethernet adapters or other devices in the wireless network.

Canada, Canada-Industry Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Caution: When using IEEE 802.11a wireless LAN, this product is restricted to indoor use due to its operation in the 5.15-to 5.25-GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High power radar is allocated as the primary user of the 5.25-to 5.35-GHz and 5.65 to 5.85-GHz bands. These radar stations can cause interference with and/or damage to this device. The maximum allowed antenna gain for use with this device is 6dBi in order to comply with the E.I.R.P limit for the 5.25-to 5.35 and 5.725 to
5.85 GHz frequency range in point-to-point operation. To comply with RF exposure requirements all antennas should be located at a minimum distance of 20cm, or the minimum separation distance allowed by the module approval, from the body of all persons.

European Union (EU) CE Declaration of Conformity
This device complies with the following directives: Electromagnetic Compatibility Directive 2014/30/EU, Low-voltage Directive 2014/35/EU, Radio Equipment Directive 2014/53/EU, ErP Directive 2009/125/EC, RoHS directive (recast) 2011/65/EU & the 2015/863 Statement. This product has been tested and found to comply with all essential requirements of the Directives.

European Union (EU) RoHS (recast) Directive 2011/65/EU & the European Commission Delegated Directive (EU) 2015/863
Statement
GIGABYTE products have not intended to add and be safe from hazardous substances (Cd, Pb, Hg, Cr+6, PBDE, PBB, DEHP, BBP, DBP, and DIBP). The parts and components have been carefully selected to meet RoHS requirements. Moreover, we at GIGABYTE are continuing our efforts to develop products that do not use internationally banned toxic chemicals.

European Union (EU) Community Waste Electrical & Electronic Equipment (WEEE) Directive Statement
GIGABYTE will fulfill the national laws as interpreted from the 2012/19/EU WEEE (Waste Electrical and Electronic Equipment) (recast)directive. The WEEE Directive specifies the treatment, collection, recycling, and disposal of electric and electronic devices and their components. Under the Directive, used equipment must be marked, collected separately, and disposed of properly.

WEEE Symbol Statement
The symbol shown below is on the product or on its packaging, which indicates that this product must not be disposed of with other waste. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling, and disposal procedure.
For more information about where you can drop off your waste equipment for recycling, please contact your local government office, your household waste disposal service, or where you purchased the product for details of environmentally safe recycling.

End of Life Directives-Recycling
The symbol shown below is on the product or on its packaging, which indicates that this product must not be disposed of with other waste. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling, and disposal procedure.

European Community Radio Equipment Directive Compliance Statement:

This equipment complies with all the requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU.
This equipment is suitable for home and office use in all the European Community Member States and the EFTA Member States.
The low band 5.15 -5.35 GHz is for indoor use only.

Wireless module manufacturer: Intel® Corporation SAS
Wireless module model name: AX210NGW

Taiwan NCC Wireless Statements
Korea KCC NCC Wireless Statement: 5,25GHz – 5,35 GHz
Japan Wireless Statement: 5.15GHz~ 5.35GHz

Wireless module country approvals:
Wireless module manufacturer: Intel ® Corporation
Wireless module model name: AX210NGW

BSMI CNS15663
Declaration of the Presence Condition of the Restricted Substances Marking

WIFI CARD
Equipment name| WIFI CARD GC-WBAX210
Type designation (Type)
---|---
Unit| Restricted substances and its chemical symbols
Lead
(Pb)| Mercury
(Hg)| Cadmium
(Cd)| Hexavalent
chromium
(Cr +6 )| Polybrominated
biphenyls
(PBB)| Polybrominated
diphenyl ethers
(PBDE)
PCB| ○| ○| ○| ○| ○| ○
Shell| ○| ○| ○| ○| ○| ○
Chip and other Active components| －| ○| ○| ○| ○| ○
Connectors| －| ○| ○| ○| ○| ○
Passive Components| －| ○| ○| ○| ○| ○
Soldering metal| ○| ○| ○| ○| ○| ○
External signal connector and cables| －| ○| ○| ○| ○| ○
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicates that the percentage content of the restricted substance
exceeds the reference percentage value of the present condition.
Note 2: ” ○” indicates that the percentage content of the restricted substance does not exceed the percentage of the reference value of presence.
Note 3: The ” －” indicates that the restricted substance corresponds to the exemption.

China RoHS Compliance Statement
Environment-friendly use period
Administrative Measures for the Restricted Use of Hazardous Substances in Electrical and Electronic Products (China RoHS Declaration)
Hazardous Substances Table

These tables are prepared in accordance with the provisions of SJT 11364
○ : The content of such hazardous substance in all homogeneous materials of such component is below the limit required by GB/T 26572.
×:  The content of such hazardous substance in a certain homogeneous material of such component is beyond the limit required by GB/T 26572.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>