LIVING SPACES 1805 Stetson Power Sofa Group User Manual
- June 6, 2024
- LIVING SPACES
Table of Contents
1805 STETSON POWER SOFA GROUP
USER MANUAL
Troubleshooting Guide This guide is to help with a non-functioning power recliner
Components:
- Switch – mounted on the side of the furniture and controls all motors and functions (reclining, power headrest, lumbar, etc.) via a direct connection with motors.
- LCD touchpad – mounted on top of the console of the love seat, controls all motors and functions( reclining, power headrest, lumbar, and light cup holder) via a direct connection with motors.
- AC wall plug – connects the power transformer to the power outlet.
- DC cord – connects the power transformer to the DC socket (mounted on the rear bottom of the LAF arm stump).
- DC socket – receives power from DC cord then transfer to motors.
- Power Transformer – A box-shaped unit to transfer 110V AC power to 25V DC power to supply for the furniture.
- Control box – connecting the switch to the seat motor and Reading light.
- Cup holder – mounted on top of the console of the love seat.
- Seat / Headrest/ Lumbar Moto r – motors mounted on the mechanism to drive movement on seat/headrest/lumbar via switch control.
- Mechanism – the motion mechanical frame unit within the piece of furniture.
- USB Ports – located on side switches (for sofa & love seat & chair) for charging USB-supported devices.
- Power Strip – located on the drop-down table and supplies 110V AC power.
- Reading light – located inside the headrest of center seat, flip up the headrest to reveal.
Quick Trouble-Shoot for Motors Malfunctioning:
Below are some possible reasons to cause motors to stop working:
- Loose connection or wires not securely plugged in.
- Broken side switch
- Broken DC socket
- Broken power transformer (especially when ALL motors stops working on one unit)
- Power cords damaged
- Motors failure
NOTE: In some cases, a button on the switch might be stuck after being pushed, thus continuously activating the motor. This can cause overheating or even damages on the power transformer.
Trou able -Shooting Guide
| NO | The fault | diagnosis | To rule out |
|---|---|---|---|
| 1 | The power supply doesn’t light up, and no output | The power supply fail |
Replace a new power supply
2| Power supply light flashing| Power self-protection function start signal,
parts, and wires may beshorted| 1 Check the surface of the actuator/hand
controller, whether is crushed
2 Internal short in the actuator/hand controller, replace the part.
3| The light of the power supply is always on, press the hand controller and
the actuator can’t work.| 1. The actuator isn’t powered, check whether the
plug is loose.
2. After checking the plug, the actuator still can’t work, exchange the
actuator is OK.
3. After checking the plug, the actuator still can’t work, exchanging the
controller is OK.| Reconnect the plug..
Replace a new actuator.
Replace a new hand controller.
4| The actuator cannot be retracted after it has been removed| Check whether
the plug is looses.
The actuator internal failure.| Reconnect the plug..
Replace a new actuator.
5| There is noise during the actuator moving| The noise is caused by the
interference of the mechanism.| Replace a new mechanism.
6| USB IPAD
USB can’t charge the IPAD| USB2A
The output current of USB is only 1A, the input of the IPAD is 2A| Can’t
charge the IPAD
7| USB
USB without output| The hand controller internal failure| Replace a new hand
controller
8| Reading light doesn’t light up.| 1 Loose connection between reading light
and touch-sensor switch
2. LED light failed.| Check and secure connection between reading light and
switch ( cable can be found behind the back of the center seat)
Replace the LED light.
Power Sofa PARTS
Console Love Seat PARTS
Power Recliner PARTS
Power Recliner Trouble Shooting
For dual-power recliners, please check the connection and integrity of the Y-Cable splitter.