progetto C1500 Como Floor Mount Bath Filler and Handshower Instruction Manual

: June 6, 2024
: progetto

Table of Contents

RECOMMENDATIONS FOR INSTALLATION
CLEANING & MAINTENANCE
INSTALLATION INSTRUCTIONS
DIVERTER OPERATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

progetto C1500 Como Floor Mount Bath Filler and Handshower Instruction Manual

progetto C1500 Como Floor Mount Bath Filler and Handshower Instruction
Manual

sales@plumbline.co.nz
www.plumbline.co.nz

RECOMMENDATIONS FOR INSTALLATION

ATTENTION : Failure to follow these recommendations may void the warranty. It is recommended that a qualified, licensed tradesperson install this product.

progetto C1500 Como Floor Mount Bath Filler and Handshower - RECOMMENDATIONS
FOR INSTALLATION

Water Pressure: 3 bar

Product performance cannot be guaranteed if pressure is less than 1 bar. Above 4 bar a pressure regulator must be installed. Failure to do so voids the product warranty.

Stop Taps/Filters

Angle valves and/or filters are recommended to prevent impurities and debris entering the mixer.

Water Temperature: 45°-65°C

progetto C1500 Como Floor Mount Bath Filler and Handshower - Water
Temperature: 45°-65°C

Pre-Flush

Always flush out the pipework before connecting any tapware. Failure to do so voids the product warranty.

CLEANING & MAINTENANCE

Cleaning

Clean with warm soapy water and a smooth cloth. Avoid abrasive sponges or detergents as these will damage the finish.

progetto C1500 Como Floor Mount Bath Filler and Handshower - Cartridge
Replacement

Cartridge Replacement

Before you start, turn off the water supply to the mixer.

Remove the handle
Unscrew the dome (hand tightened)
Unscrew the locking nut
Remove the cartridge

Re-assemble in reverse order

Max tightening torque on locking nut: 10-12 Nm

Aerator Maintenance

Remove the aerator with an aerator cartridge key.
Immerse for half a day in water-vinegar solution (80-20%).
Wash, then reassemble.

Warranty Information

For full details about our warranty visit plumbline.co.nz/warranty- information

INSTALLATION INSTRUCTIONS

progetto C1500 Como Floor Mount Bath Filler and Handshower - INSTALLATION
INSTRUCTIONS

The Underfloor Mounting Box must be recessed into the floor and levelled (using the spirit level provided) as shown.

$progetto C1500 Como Floor Mount Bath Filler and Handshower - The Underfloor Mounting Box must be recessed into the floor and levelled $using the spirit level provided$$

Slide the flange over the bottom part of the mixer body and attached the mounting plate to the underside of the mixer body.
Drill the holes for mounting the Underfloor Mounting Box

progetto C1500 Como Floor Mount Bath Filler and Handshower - Drill the holes
for mounting the Underfloor Mounting Box

Wrap PTFE tape on the inlet elbows provided and screw them into the Underfloor Mounting Box.
Set the Underfloor Mounting Box into the recess in the floor and level using the spirit level provided.

progetto C1500 Como Floor Mount Bath Filler and Handshower - Wrap PTFE tape
on the inlet elbows provided

Fix the Underfloor Mounting Box to the floor with toggle bolts provided.

progetto C1500 Como Floor Mount Bath Filler and Handshower - Fix the
Underfloor Mounting Box to the floor

Connect the hot & cold inlet pipes to the inlet elbows.
Pressure test the whole unit before sealing the floor to ensure there are no leaks.
Complete the finished floor surface, ensuring the floor surface is finished up to the edge of the Underfloor Mounting Box.
Remove the fixing plate, spirit level and blank cover caps.
Fit the fixing plate onto the mounting plate (already attached to the Mixer Body in step 1).
Align the copper pipes with the relevant hot & cold connector holes on the Underfloor Mounting Box. Fasten the fixing plate to the Underfloor Mounting Box.
A check valve is pre-installed in the handshower. Connect flow regulator to the handshower if necessary.