KLH AMES Bookshelf Loudspeakers Instruction Manual
- June 6, 2024
- KLH
Table of Contents
WELCOME!
Thank you for purchasing one of the best sounding speakers ever produced. At KLH, we have been making high-quality components since 1957, and we take pride in making your music and movies the best experience possible.
FOR YOUR SAFETY
Important Safety Instructions!
- READ these instructions.
- KEEP these instructions.
- Heed all warnings.
- FOLLOW all instructions.
- DO NOT use this apparatus near water.
- CLEAN with a dry cloth.
- DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other heat-producing appliances
- ONLY USE attachments/accessories specified by the manufacturer.
- DO NOT expose to excess moisture or liquids, and do not place containers with liquids on top of speakers.
The exclamation point, within an equilateral triangle, is intended to alert
the user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
The lightning flash with an arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electrical shock to persons.
WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified service personnel.
EU COMPLIANCE INFORMATION:
Eligible to bear the CE mark, Conforms to European Union EMC Directive
2004/108/EC; European Union Restriction of Hazardous Substances Recast (RoHS2)
Directive
2011/65/EC; European Union WEEE Directive 2002/96/EC.
KLH and the KLH logo are registered trademarks of Kelley Global Brands Inc.,
registered in the U.S. and other countries.
WE NOTICE
Note: This mark applies only to countries within the European Union (EU)
and Norway.
This appliance is labeled in accordance with European Directive 2002/96/EC
concerning waste electrical and electronic equipment (WEEE). This label
indicates that this product should not be disposed of with household waste. It
should be deposited at an appropriate facility to enable recovery and
recycling.
UNPACKING
Place the package on the floor or tabletop with the box flaps up. Cut the tape
with a utility knife to open the package. Fold the carton flaps back and
carefully slide the speaker and packaging from the box, or turn the box over
with flaps open and remove the box. Stand the speaker and pack upright, making
sure the speaker is right side up, and remove the packing material.
CONNECTING YOUR MONITORS
Both monitors have the same quality nickel-plated binding posts (the Ames
monitor has single posts only and cannot be bi-amped) that will accommodate
stripped wire, spade connectors, or banana plugs. Be sure to use quality
speaker cables, up to 12 gauge (AWG). The lowest gauge possible is
recommended. Before using banana plugs, be sure to remove the black and red
inserts on the binding posts. The straps connecting the binding posts should
remain in place for conventional wiring but may be removed where bi-wiring is
referred (Albany only). See the following diagrams in the AMPLIFICATION
section for further instruction.
AMPLIFICATION
Conventional amplification involves a single stereo amplifier wired to a
single set of binding posts with straps connecting the second set of posts as
seen in the diagram above. Simply attach the positive wire + to the red post
and the negative wire – to the black post.
BI-AMPLIFICATION
This connection method (see diagram above) uses two separate two-channel
amplifiers to power one set of speakers. One stereo amplifier connects to one
speaker, and the ther identical amplifier powers the second speaker. This is
referred to as bi-amplification.
Be sure to remove the terminal straps before using the bi-amplification
method. Connect positive + and negative – cables from the amplifier to the top
terminals, and make sure the connection is tight. Connect the second set of
cables (positive and negative) to the bottom terminals and tighten. Repeat
these same steps using the second amplifier to connect to the second terminal.
ROOM POSITION
Placement of your monitor speakers is a personal preference, but it is
recommended that speakers be placed at least 6 feet apart whether they are
being used for a stereo pplication, or as the main left and right channels for
a home theater. For best imaging and separation, the listening distance from
the speakers should be about 1.5 times the distance the speakers are apart
from each other.
Example : If the distance between each speaker and the listening position
is 9 feet, then the speakers should be 6 feet apart from one another.
Also, be sure that speakers are placed at least 12 inches away from any wall.
Further adjustments can be made to optimize your listening experience.
Monitor loudspeakers should be placed on stands or on bookshelves, preferably
at ear level with listeners. These KLH monitors may also be used as surround
speakers if desired.
WARRANTY
Our 10-year parts warranty begins from the purchase date of the item (invoice
date). For warranty/service issues, please contact your place of purchase.
Please keep your original
receipt. The warranty covers any production and material defects of the
product. Warranty registration may be completed at
klhaudio.com/warranty
The following is NOT COVERED by the warranty:
1. Accidents, misuse, poor maintenance, electrical overloads such as
lightning or voltage.
2. Repair must be performed by an authorized KLH dealer or service center3.
Incorrect installation of the product.
4. Altered serial number.
5. Transportation costs for service calls.
6. Purchase of KLH products from unauthorized resellers.
The replacement item cannot exceed the cost of the item under warranty. The
supplier is responsible for only repair or replacement.
SPECIFICATIONS
Albany Bookshelf Speaker
Frequency response | 35Hz-23kHz.+/-3dB |
---|---|
Sensitivity | 92dB |
Power handling | 200 watts |
Components | 1 x 5.25” Woven Kevlar bass drivers, and 1 high performance 1” |
Anodized Aluminum tweeter
Finishes| Walnut Wood Veneer or Black Oak Wood Veneer
Impedance| 8 Ω
Crossover point| 2.4kHz.
Dimensions:| 13” x 6.5” x 9.5” (H x W x D)
Weight:| 11.24lbs
Ames Bookshelf Speaker
Frequency response | 60Hz-23kHz+/-3dB. |
---|---|
Sensitivity | 87.5dB. |
Power handling | 150 watts. |
Components | 1 x 4” Woven Kevlar bass driver and 1 high performance 1” Anodized |
Aluminum tweeter
Finishes| Satin White or Satin Black
Impedance| 8 Ω.
Crossover point| 2kHz.
Dimensions:| 7.5” x 4.75” x 6” (H x W x D).
Weight:| 5lbs
984 Logan Street, Suite 301
Noblesville, IN 46060
klhaudio.com