DIG FM01AS Patio Drip Watering Kit Installation Guide
- June 6, 2024
- DIG
Table of Contents
INSTALLATION INSTRUCTIONS
Patio Drip
Watering Kit
Model FM01AS with Backflow Preventer
INTRODUCTION
Thank you for purchasing the DIG model FM01AS Drip Watering Kit. Please take the time to read through the enclosed instructions and follow them step by step. If you have any questions, please call our customer service line at 1-800-344-2281. Use model FM01 or FM01AS Patio Drip Watering Kit to maximize your efficient use of water and to promote abundant growth in your planters, potted plants or baskets. If you decide to expand your system, all the necessary parts are available individually from a DIG distributor.
ABOUT YOUR PATIO DRIP WATERING KIT
The FM01AS Drip Watering Kit is designed to irrigate plants in hanging baskets, pots, and planters. This kit contains all the necessary parts to install a drip system for up to 10 pots or baskets. Note that two emitters should be used for larger pots (12″–18″). This drip kit can be easily expanded to irrigate up to 15 pots or baskets. Before the installation, familiarize yourself with all the parts in this kit. See the part list and description at the end of this instruction manual and on the back of the box.
PLANNING SUGGESTION
Determine the number of pots or baskets you need to water, taking into account
that pots greater than 12″ need two or more drip emitters.
Option 1: For baskets up to 10″, use one dripper per pot. To do this, run the
1/4″ micro tubing mainline to the pot or basket. Cut the micro tubing near the
pot or basket and add a 1/4″ tee. To the tee, add an additional section of
micro tubing, which becomes the feeder line. Run the micro tubing feeder line
into the pot or basket about 1″ from the plant. Insert a dripper into the end
of the micro tubing and secure the dripper with a tubing holder stake.
Option 2: For larger baskets (12″-18″), install two drippers per pot. To do
this, run the 1/4″ micro tubing mainline to the pot or basket. Near the pot or
basket cut the micro tubing and add a 1/4″ tee. To the tee, connect a length
of micro tubing, which becomes the feeder line. Run the micro tubing feeder
line into the pot or basket. Inside the pot or a basket, split the microtube
into two feeder lines using an additional 1/4″ tee and two pieces of micro
tubing, 3″-5″ length. At the end of each micro tubing feeder line, add one
dripper and secure the dripper using the tubing holder stake.
Ideally, when everything is connected and running, each pot on a system should
begin to drain water at about the same time. If this is not happening, it is
usually because there are various pot sizes. A 1/4″ valve can be added to
control the flow to each pot or section of pots. When planning out your
system, it is common to group like-size containers on one line, sectioning out
the pots. In this situation, a single 1/4″ valve can control the flow to a
number of similar-sized pots. If this is not possible because of the layout of
the pots, which is common, a 1/4″ valve can be added to each line to
individually control the water to the pots. This ball valve will allow you to
adjust the flow by turning the knob to either side.
Note: There are two ball valves available in the kit. If more ball valves
are needed, use Model D33A, Part #65.
INSTALLATION
Step 1: Faucet (Hose End)
Begin the installation at the water source by attaching the 3/4″ FHT backflow
device to the faucet (Model FM01AS). If automating the system, connect the
hose end timer (not included) into the faucet and connect the backflow device
to the hose end timer. To the backflow device, connect the 3/4″, 25-PSI preset
pressure regulator and then thread the 3/4″ FHT x 1/4″ compression adapter
with the screen.
Note: This Kit is intended for outdoor use only, do not install indoors.
The maximum incoming pressure is 80 PSI. Tighten threaded fittings by hand
only. No wrench or Teflon tape is required.
Step 2: Micro tubing Placement & Connection
Unroll the 1/4″ micro tubing and lay it out in the area of the planters,
containers or baskets to be watered. Connect the micro tubing to the adapter
by forcing the micro tubing end directly into the compression side of the
adapter while moving the micro tubing from side to side. No barb is needed.
Step 3: Connecting the 1/4″ Tees
The micro tubing serves as the primary line that runs water to all the plants.
Near each planter, container or basket cut the 1/4″ micro tubing and insert a
1/4″ tee (soaking the micro tubing in hot water will ease installation). Leave
the end of the 1/4″ micro tubing open so you can flush the line before
completion. Run a piece of 1/4″ micro tubing from the center of each pot,
container, or basket and connect each to the 1/4″ tee. Use a 1/4″ barbed elbow
or connector as needed.
Step 4: Connect 1/4″ Ball Valve (optional)
To control the flow rate, 2″-4″ from a large container or basket, cut the
feeder line (micro tubing) and attach a 1/4″ ball valve to allow flow
adjustment for individual containers or baskets.
Note: if containers of similar sizes are grouped on one section of line,
a single valve can be placed at the head of the micro tubing feeder-line
section to control the flow to multiple baskets.
Step 5: Flush the Line
Turn the water on, and flush the line for 10-20 seconds to flush out any
debris inside the system.
Step 6: Installing the Drip Emitters
For small containers and near the plant, insert a drip emitter into the end of
the micro tubing. Attach a holder stake to the micro tubing and secure it to
the pot. For larger planters and containers, see option 2 in the planning
suggestion section.
Step 7: Secure Micro tubing
Secure the micro tubing to the patio, containers or planters using the 1/4″
C-clamps.
Step 8: System Start-Up
Begin by turning the water on. If used, adjust the flow of the 1/4″ ball valve
as needed by turning the knob.
NOTE: If each pot drains at different times (probably because they are
different sized pots) you may want to consider using a 1/4″ valve on each
line. This will help control the flow so that each pot drains at the same time
regardless of size.
When watering on a regular basis, it is ideal to allow very little water to
drain out of the pots. This helps conserve water and generally keeps the area
cleaner. After initial start-up, determine how long the system should run
each time to sufficiently irrigate the pots without excess runoff. To do this,
run the system checking to see how long it takes all the pots to drain. Set
the irrigation schedules 1-2 minutes less than it takes for the pots to drain.
For example, if it initially took the pots 5 minutes to all begin draining,
set the system to run for about 3-4 minutes each time. The watering can be
automated by using battery- or solar-powered timers such as our BO9D or
EVO100. After a week, check the soil and the health of the plants and adjust
the watering time as needed.
KIT CONTAINS
| Product Description FM01AS| Quantity
---|---|---
| 3/4″ FHT x MHT Backflow Device| 1
| 3/4″ FHT x MHT 25-PSI Preset Pressure Regulator| 1
| 3/4″ FHT x MHT Compression Adapter| 1
| 1-GPH PC Dripper| 10
| 60′ of 1/4″ Micro Tubing| 1
| 1/4″ Barbed Connector| 2
| 1/4″ Barbed Elbow| 10
| 1/4″ Barbed Tee| 9
| 1/4″ Holder Stake| 10
| 1/4″ Tubing C-Clamps| 10
| 1/4″ Barbed Ball Valve| 2
| Instruction Manual| 1
All parts are also sold separately at DIG retailers.
DIG CORPORATION 3 YEAR WARRANTY
DIG CORPORATION warrants these products to be free from defects in material and workmanship for a period of three years from the date of purchase. This warranty does not cover damage resulting from accident, misuse, neglect, modification, or improper installation. This warranty shall extend only to the original purchaser and user of the product. The obligation of DIG CORPORATION under this warranty is limited to repairing or replacing at its factory this product. This product must be returned to the factory within three years after the original purchase and upon examination, is found to contain defects in material and workmanship.
DIG CORPORATION SHALL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND; THE SOLE OBLIGATION OF DIG BEING LIMITED TO REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
Unattended use for prolonged periods without inspection to verify proper operation is beyond the intended use of this product. Any damage resulting from such use shall not be the responsibility of DIG CORPORATION. There are no warranties that extend beyond the description on the face hereof. In the case of purchase of the product for use other than for irrigation purposes, DIG CORPORATION hereby disclaims any implied warranties, including any warranties of merchantability and fitness for a particular purpose. In the case of the purchase of the product for personal, family, or household purposes, DIG CORPORATION disclaims any such warranties to the extent permitted by law. To the extent that any such disclaimer or implied warranties shall be ineffectual, then any implied warranties shall be limited in duration to a period of three years from the date of the original purchase for use by the purchaser. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
In order to obtain performance under this warranty, the unit must be returned to the factory, along with proof of purchase indicating original date of purchase, shipping prepaid, addressed as follows:
DIG CORPORATION, 1210 Activity Drive, Vista, CA 92081. Repaired or replaced
units will be shipped prepaid to the name and address supplied with the unit
returned under warranty. Allow four weeks for repairs and shipping time.
Repair of damaged units, not otherwise within warranty may be refused or done
at a reasonable cost or charge at the option of DIG CORPORATION.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
1.800.322.9146 FAX: 760.727.0282
1210 Activity Drive
Vista, CA 92081-8510
www.digcorp.com
dig@digcorp.com
Printed in the USA. We at DIG strongly believe in conservation.
Please recycle whenever possible. 072318 26-009
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>