flashbay DT2111 Earphones User Manual

flashbay DT2111 Earphones User Manual

Product Overview

• A: Multi function button. See below for all functions.
• B: LED light. Red: Charging in case | LED turns off once fully charged | Red & Blue flashing: Paring | Blue flashing: Paired.
• C: Audio output.
• D: Charging contact points.
• E: Charging case battery status display (0-100).
• F: USB-C charging port.
• G: Charging case.

Turning on

The earphones will automatically turn on when you take them out of the charging case. You can also turn on the earphones by pressing and holding button for 3 seconds.

Pairing

1. Ensure that Bluetooth ® is activated on your phone, tablet or other device.
2. With the earphones out of the charging case, the LED lights will flash red and blue alternately, the earphones are now in pairing mode.
3. On your device, select “Promo Audio” to pair.
4. The LED light will flash blue once successfully paired.
5. The earphones will then automatically connect to your preferred device when turned on again.

Unpairing

You can unfair the earphones from your device via any of the below options:

1. Put the earphones back in the charging case.
2. Disconnect via your device’s Bluetooth ® settings menu.
3. Selecting ‘Forget Device’ via your device’s Bluetooth ® settings menu.

Play / Pause

Press button on either earphone to play and pause music.

Skip Songs

When playing music, press button three times on either earphone to skip the song

Volume Control

Press button twice on the left earphone to increase the volume. Press button twice on the right earphone to decrease the volume.

Activate Siri for iPhone users

Hold button on either earphone for 2 seconds to activate Siri.

Call answering and Call hang up

Press button on either earphone to answer a call. You can then press button again to hang up.

Reject a Call

Press and hold button for 2 seconds on either earphone to reject an incoming call.

Low battery prompt

When the battery is running low, a ‘low battery tone’ will be played every 30 seconds until the earphones are powered off or placed in the charging case.

Turning off

The earphones will automatically turn off when you place them into the charging case. You can also turn off the earphones by pressing and holding button on either earphone for 5 seconds.

Charging the case

1. Connect the USB-C cable to a power source and then plug the USB-C cable into the USB-C port on the side of the charging case. The max input voltage and current should not exceed 5V and 200mA respectively.
2. The charging case will take approximately 2 hours to be fully charged.
3. The LED number on the outside of the case will read ’100’ when the case is fully charged.

Charging the earphones

1. Place the earphones into the charging case, ensuring that the connection points are in contact.

2. The LED on the earphones will show a static red light whilst the earphones are
   charging.
3. The red LED light will turn off once the earphones are fully charged.
4. The earphones will take approximately 1 hour to fully charge.

Safety and Compliance Information

• Do not attempt to disassemble the product or insert items into the product as this may cause short circuits resulting in electrical shock or fire.
• The product contains no user replaceable parts. Only authorized service engineers may open the product.
• This product is not waterproof or water resistant. Exposing the product to rain, moisture or other liquids may damage the product and may result in injury to the user. Do not touch or use with wet hands.
• Do not use in areas where there is the risk of explosion.
• The product package contains small items and packaging that may be hazardous to children and may pose a choking or strangulation hazard. Keep the product, accessories and packaging out of reach of children at all times. This product is not a toy.
• If the product is damaged in any way, pierced, dropped, exposed to liquid, if the product overheats or if the charging cable is damaged discontinue use immediately.
• Do not connect to any input power supply other than stated at the top of this page.
• Always keep the product between 0°C and 45°C. Operation outside this range may damage the product or cause harm to the user.
• CAUTION: The battery used in this product may present a risk of fire, explosion, electrical shock or chemical burn if mistreated.
• The battery in this product is not user replaceable and should only be handled by authorized service engineers.
• Only use the charging cables provided with the Earphones and the charging device, do not charge with other cables.
• Do not dispose of the product in household waste as this may result in fire, explosion, electrical shock or chemical burn.
• Under certain conditions, exposing the device to a strong electrostatic discharge may cause the device to stop operating. Resulting in the need to reset.

ISED Statement

This device contains license-except transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canda’s license-except RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Please remove the batteries safely with appropriate tools when disposing of the earphones or batteries. Please use designated collection or recycling facilities.

FCC ID: 2ALRV-DT2111
Left earphone:
IC : 22713-01DT2111
HVIN: 01DT2111
Right earphone:
IC : 22713-02DT2111
HVIN: 02DT2111

Note: The FCC ID: 2ALRV-DT2111 is only for the earphone (not charging case).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>