PHILIPS Smart7 Lid Battery Operated LTE Cellular GPS Tracker User Manual

: June 6, 2024
: Philips

Table of Contents

PHILIPS Smart7 Lid Battery Operated LTE Cellular GPS Tracker
INTRODUCTION
HARDWARE FEATURES
BATTERY PACK AND POWER SUPPLY
TECHNICAL DATA
MECHANICAL DETAILS
COMPANY INFORMATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PHILIPS Smart7 Lid Battery Operated LTE Cellular GPS Tracker

Battery Operated LTE Cellular GPS Tracker
Part #77-6811

INTRODUCTION

The Battery Operated LTE Cellular GPS Tracker from Phillips Connect Technologies is a vehicle tracking device that combines GPS location with LTE and Bluetooth. The Smart7 Lid monitors vehicle functions and collects data for tracking and analysis.
The Smart7 Lid appears to the user of a server application as a single endpoint device. It can be queried, updated, and configured either through a serial connection or an over-the air (OTA) LTE IP connection. The Smart7 Lid presents itself over the connections as an enhanced cellular modem with attached functional elements. These elements include:

GPS location engine
General Purpose Bidirectional I/O (GPIO) pins
Relay drive pin output
Serial UART port
CAN Communication (optional)
BLE 5.0

The following is a typical application scenario:

HARDWARE FEATURES

The Smart7 Lid ships from the factory pre-configured for a specific set of functions and is completely configurable in the field, while providing support for external control through a Phillips Connect proprietary set of AT commands. Supported features include the following:

CELLULAR GATEWAY
An integrated cellular gateway provides continuous 4G-LTE connectivity to the trailer. A multi- carrier SIM assures comprehensive coverage.

4G-LTE Cat-1(bands 2, 14, 12)
3G-HSPA fallback (bands II, V)
Roaming w/VPN onto TMO, ATT, VZ
Canada, LatAm plans available ƒ Secure reports delivery with ACKnowledge
Report queue size: 2000
OTA update of all firmware components
OTA update of compatible sensors

REPORTING
Reporting while on a trip includes:

1- to 5-minute breadcrumbs (configurable)
Heading changes
Sensor data and alerts Reporting while stopped includes:
Daily heartbeats (configurable)
Vibration / motion-detection
TPMS and Tilt alerts
Tractor pairing
Door open/close
Cargo status change
PreCheck alerts
Current ABS Fault Code

GPS / LOCATION TRACKING
High performance GPS tracking means you always know where your trailers are located.

25mm x 25mm sky-facing ceramic patch antenna
GPS L1 band 1575MHz
GPS-based odometer accuracy: > 99.5%

INTEGRATED ABS MONITORING (THROUGH PLC)
Compatible with most ABS manufacturers.

Retrieved ABS data includes:
Fault lamp status
DTC trouble-codes (active & stored) ƒ Odometer
VIN (if programmed into ABS)

TRAILER PRECHECK
Know what to expect before the driver arrives with Schedule-based or Remote- On-Demand
PreCheck of trailer sensors… or conduct an onsite live PreCheck prior to tractor hookup.

1A @ 12V supply for external sensors
External sensors include TPMS, cargo, ABS, trailer-weight, and more

BLUETOOTH WIRELESS SENSOR SUPPORT

Bluetooth 5 LE class II transmitter
Receive sensitivity -96dBm
Compatible sensors include:
o SmartPair™, Door✓™
o SmartLock™ gladhand
o Micro SP Transceiver

HARNESS INTERFACES

Optional data harness for additional wired sensors using RS485, UART, or GPI

BATTERY PACK AND POWER SUPPLY

10.6A-Hr recharge-able Li-ion battery pack
~6 months untethered operation
4hrs to 90% charge from either Aux or Marker circuit power
360mA integrated solar panel
Maximum 2A current draw from tractor
Tracking mode: 50mA battery current
Idle mode: 2mA battery current
Sleep mode: 100μA battery current

PHYSICAL DIMENSIONS AND MOUNTING

Length 13.6” x Height 7” x Depth 4.1”
Mount with 2 x 5/16” bolts

ENVIRONMENTAL

IP67 protection for electronics and battery
Operating temp. range: -40C to 70C
Battery charging temp. range: -20C to 45C

CERTIFICATIONS

FCC / IC
BQB Bluetooth
PTCRB cellular
RoHS compliant

TECHNICAL DATA

Smart7 Lid RF Specifications

4G LTE Cat 1
Band| Band 2/4/5/12/25/26
Rx Spec| Follow TS 36.521. Ch. 7
Tx Spec| Follow TS 36.521. Ch. 6
BLE 5.0
ISM Band| 2.4 BHz
Rx Spec| Follow Chipset
Tx Spec| Follow Chipset
GPS
Frequency Support| L1-band (1.57542GHz)
General Hardware Specifications

MECHANICAL DETAILS

FRONT/REAR DIMENSIONS

SIDE DIMENSIONS

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE: FCC Radiation Exposure Statement
This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

ISED Statement
English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).