D-3 TECHNOLOGY EZ-Bell Doorbell Camera User Guide
- June 6, 2024
- D-3 TECHNOLOGY
Table of Contents
TECHNOLOGY EZ-Bell Doorbell Camera
User Guide
Introduction
Next-generation video doorbell camera – EZ-Bell is your multifunctional doorkeeper, enabling you to receive doorbell alarm and home security event alarm, to make calls with visitors, to view real-time streaming or motion trigger video and playback video.
Included materials
- Doorbell Camera*1
- Wall mounting bracket*1
- Angle correction plate*1
- Wall screw*2
- Doorbell fixing screw*3
- Expansive rubber sleeve*2
Product Appearance
Product Features
- Live view streaming via Mobile APP or Security Panel.
- Two-way Audio through Mobile APP or Security Panel.
- Security RF included. Connecting the complete ecosystem: Panel, Sensor, Doorbell.
- Expansive FOV 202(H)*119(V).
- Full HD 1920 x 1080 Video resolution.
- 2T2R Dual-band 2.4GHZ/5GHZ WIFI for improved WIFI range.
- On-device AI. Instant analysis of each event and accurate reduction of false triggers.
- Real-time communication to anyone who approaches your door via 2-way Audio.
- Pre-record supported. Capture all actions in video clips to be stored at the Amazon server.
- As a sensor to Panel, the doorbell camera can send outdoor motion events to Panel.
- Compatible with the existing doorbell transformers (10-30VAC,10VA)
- Compatible with Mechanical and Digital Chimes.
Product Specification
Model Name:
EZ-Bell V1 (XDC01)| Video compression format
H.264+ AAC/PCM
For Video Clip and Video streaming
---|---
Memory:
2GBit Embedded DDR3| Network protocol
P2P Video streaming/ Camera configuration HTTPS and OTA support
Image sensor:
1/2.7 FHD (1080P) sensor| Night Vision
B&W Night Vision/850nm 016ft
Streaming resolution: HD(720P)/FHD(1080P)| LED
RGB color status LED
Video framerate
Variable framerate 10-15fps| Chime
Security Panel (XP02) as Doorbell Chime AC Mechanical Chime
AC Digital Chime (Works with DDA board)
OS:
Dual OS (RTOS + Linux 4.9)| Storage:
Local Storage: N/A (Reserved MicroSD Socket) Cloud Storage: Amazon KVS Video
storage
Field of View:
202(H)’ 119(V)| Power
10-30VAC, 10 VA, OR 12 VDC 0.5A Battery: Built-in 450mAh battery
WIFI/ SubG RF radio
WIFI: IEEE 802.11 a/b/g/n/ac 2T2R 2.4/5GHz dual band SubG RF: 433MHz|
Operation Temperature
Product working temperature: -10°C – 45°C
Motion Detect
Motion sensor/130° @ 8FT
Al Human detection algorithm to reduce false trigger Support pre-recording
before Motion trigger| Waterproof IPX4
Weight
94g
110g (with mounting plate)
Video /Audio Streaming
Full-duplex two-way call| Certification
FCC/IC
Requirement
-
Power
10-30VAC, 10VA or 12VDC, 0.5 to 1.0A wired to an in-home mechanical or digital doorbell chime. Note: A Digital Doorbell Adapter must be installed if a digital doorbell chime is present.
WARNING: An in-line resistor (10 Ohm, 10 Watt) is required when installing the doorbell camera without a wired, in-home doorbell chime. This is typically done when testing the doorbell or performing a demonstration. Failure to install a resistor when a chime is not present may result in damage to the doorbell camera. -
Chime
• Security Panel (XP02) as Chime – XP02 Panel can be a chime of the EZ-Bell doorbell.
• Mechanical Chime – If the chime has metal bars and a striker pin, it is mechanical and will work without additional hardware.
• Digital Chime – If the chime has a speaker that plays a tone when pressed, it is digital and will require the installation of the Digital Doorbell Adapter and the enabling of the digital doorbell setting in the app to function properly.
• Tube Chime – If the chime has a series of tubular bells, it is a tube chime and is incompatible with the doorbell camera.
• Intercom System – If the doorbell button fixture includes a speaker, it is an intercom system and is incompatible with the doorbell camera.
• No Chime – If there is no chime in the system, the customer will only receive alerts on their phone and a resistor (10 Ohm 10 Watt) must be used in- line with the doorbell camera. -
WiFi
A Wi-Fi Internet upload speed of at least 1.5 Mbps is required at the location where the doorbell camera is installed.
Note: In Canada when using 5 GHz on band 1, the device is intended for indoor use only.
Hardware Installation
APP Instruction
- 8.1 – Camera Pairing and Provision
- 8.2 – Live view streaming and 2-way talk
-
Click “watch live”
-
Call-out or pick-up call: Click the dial green button.
-
Hangup: Click red hangup icon
Push talk: Press blue mic icon;
Snapshot: Click the grey camera icon.
- 8.3 – Video Clip Online Playback
-
Click “History” on the right foot
-
Select event to view
-
View online playback in full screen
Doorbell LED Pattern
LED Indicator Reference Card
| COLOR DESCRIPTION | STATUS |
|---|---|
| WHITE – solid | Ready mode |
| GREEN – solid | In-Call mode |
| BLUE – breathing | System booting |
| ORANGE – breathing | Device pairing mode |
| ORANGE – flashing | Pairing process |
| WHITE – breathing | WiFi reset |
| BLUE – fast flashing | Factory reset |
| BLUE – solid | Firmware upgrade |
| YELLOW – solid | Connecting to Router fail WiFi password was wrong Connecting |
to Server fail
RED – flashing| Panel alarm
CYAN- slow flashing| Charging battery
Warning：
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC warning:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection Confidential for D3
Internal Use Only against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator & your body.
The distance between user and products should be no less than 20cm.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>