Shenzhen Avanline Digital Tech DA Handheld Videoscope User Manual
- June 6, 2024
- Shenzhen Avanline Digital Tech
Table of Contents
Handheld video scope
Model: DA
FCC ID: 2A3A7-DA
Safety Recommendations
DANGER
-
This device must not be used for medical or veterinary purposes.
-
Do not use this item in explosive atmospheres.
-
Do not look into the distal end with naked eyes, eyesight may be harmed by strong light.
WARNING -
Keep the device out of reach of children.
-
Do not try to modify or disassemble the unit.
-
Do not pull hard or twist the insertion tube.
-
The serious impact may bring breakage of lens components at the distal end.
-
Do not use or store the instrument at a temperature higher than 60°C or lower than -20°C.
-
Store the instrument in a dry and well-ventilated environment.
Parts Function
Quick Setup
1. Detachable Panel
Take apart: Screw off the bolt on the back of the panel, then push the panel
upwards, which will be taken apart from the main body. Fig01. The reverse
operation combines the two parts together.
2. Ready for use
At shutdown status, plugin Micro SD in direction. Fig03
Long press button, the status indicator turns green, the device enters preview mode, the real-time image shows on the screen and at the same time, some icons and time information will be seen at the top location. Fig04
NOTE
Definition
Press: press and release less than 1 sec. Long press: keep press for around 3
secs.
Through button to adjust the illumination, steer the joystick to control
distal end to bend. The locker is to tighten or release the joystick in order
to distal the end stay at a certain angle. Fig05.
MENU set up
Switch on the device and enter preview mode, press MENU to access menu interface, use to select item and with OK to confirm.
The menu options are listed as below:
Time watermark
Loop Record
Recording
Date/time
Language
Brightness
Format
Default setting
Version
WIFI
Pressing the MENU key enables to end of the current menu setting job and jump to the MENU interface so as to enter other items.
Time watermark
Using to select turn off or open, with an OK key to confirm, the open
allows video to be recorded with a time mark.
Loop Record
Video files consist of consecutive clips with the same duration, the duration
is optional :
Permanent
1 minute
3 minutes
5 minutes
Permanent means the whole video is to be recorded as a single clip.
Sound Recording
Under this item, to select open, the surrounding sound and video will be
recorded simultaneously. At the same time, the icon on the top of the screen
is changed. The function also can be activated by a shortcut key .
Date and Time
Using to increase or decrease the number, press OK to move to the next step.
Fig 06.
Language
Select required language with, Press OK to confirm the choice.
Brightness
Through this menu, you can change the brightness of light on the camera end,
total 4 levels optional, and off to turn off the light.
In most cases, you should use the key to adjust brightness more often.
Format
In some cases, micro SD cards can not work properly, you can try to format the
c ard to fix the problem. Please back up files in advance due to the data
could be lost in the process.
Default setting and Version
By the two items, you can get to the factory setting and see the current
software version.
WIFI
Select On or Off to choose the WIFI function to be activated or not, the color
on the top of the screen will turn gray to blue that indicating the WIFI is
active.
Scan QR code on the screen to load down APP onto your smartphone, you can also
search RoadCam in android or apple store to get the APP.
To Set WLAN on your phone, find the net: wifi_camera _XXXXXXXXX and join it,
then open the APP, the image will be present on your phone screen.
NOTE The function of keys on the panel is disabled until the wifi net is
disconnected in the WLAN setting on your phone.
NOTE A separate using manual for WIFI function is available, please
contact your dealer to get detailed information.
Take pictures and Video recording
Take picture
In preview mode, press Snap to take a picture, the picture is stored on a
Micro SD card with a file name of the running number. Such as: IMG_0000002
.JPG
Video recording
In preview mode, Long press Snap to take video, the video file name is related
to date and time. Meanwhile, you can get a snapshot during the video recording
process, the snapshot picture is stored with the running number. For example
VID_20210116_110110.MOV CAP_0000002.JPG
Image viewing
-
In preview mode, press, the image last picture or video will present, please use to find the image wanted. Fig07.
-
Press OK to play video, press OK again to pause, press OK once more return to play.
-
Press to fast-forward, to back-forward, repeatedly press the key to get 2x 4x 8x speed.
Delete files
When you find a targeted picture or video, press MENU to delete files, press OK to choose to delete the current single one or all files. -
Long press MENU, jump to preview mode.
Storage & Maintenance
1. Rechargeable battery
Charging time around 7 hours till the indicator turns off, the fully charged
battery can continuously work for 5 hours with LED ring illumination, around 2
hours for fiber illumination.
2. Cleaning components
Cleaning insertion tube Wipe thoroughly with a piece of gauze or other
material moistened with neutral detergent, next clean by gauze moistened with
clear water, and then wipe the insertion tube dry off all moisture.
NOTE
Clear the insertion tube immediately after withdrawing the insertion
tube.Leave the very dirty insertion tube for long periods can cause it to be
corroded. Cleaning distal end
Grasping the rigid portion of the camera end, use a clean soft piece of gauze
or cotton swabs to wipe off dirt and water. Best results may be obtained using
commercially available absolute ethanol.Fig08
Cleaning unit body Wipe with a soft cloth dampened with clean water, and wipe with a clear and dry cloth.
3. Storage precautions
Store the instrument under normal room temperature and humidity. Straighten
angulation section while lay into carrying case. Store the equipment in a
clean, dry, and stable place.
Q & A
Q: No image on the screen after turning the power on 1
`A: Battery is exhausted. Connect the panel to the power adapter and recharge.
Q: Unable to take photos or record video
A: SD card absent, wrongly inserted, full, or faulty.
Q: Shut down
A: When all functions freeze or fail, insert an insulated needle into the hole
on the side of the main unit, restart the device to find if the problem is
resolved.Fig09
System parameters
Display Unit
LCD Panel| 4.5’’ TFT LCD
MicroSD Card, support 128GB
---|---
Power source| Lithium battery 3500mAh
AC adapter: Input 100-240VAC 50/60Hz, Output 5VDC
Operating Environment
| Operating Temperatures | The distal end and insertion tube: 0-60° C |
|---|
Other parts excepted of above: 0-40°C
Operating Humidity| 15-90% RH
Waterproof| Insertion tube Ip67
Other parts Ip52
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>