WOGREE S60 Wireless Sound Bar User Guide

WOGREE S60 Wireless Sound Bar

Important Safety Instructions

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install IN accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers ,stoves, or other apparatus(including amp liters)that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type ploughs two blades and a third grounding prong. The wide lade or the third prong are provided for your
   safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles ,and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Unplug this apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord prolog is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

SPECIAL NOTE

When placing your unit on a lacquered or natural finish, protect your furniture with a cloth or other protective material.

FCC WARNING

Warning : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not causeharmful interference, and(2)this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on ,the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an an controlled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

Additional Warnings
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus.
Battery shall not be exposed to excessive heat such as sunshine, fire or the light.
Caution marking is located at the rear or bottom of the apparatus.
The marking information is located at the rear of bottom of apparatus.

This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts.

What’s in the box

Make sure you read all the safety information before you use this product.

Overview

Sound bar main unit and how to use it

Sound Bar Main Unit

Sound bar LED Display

The LED display on the Sound Bar gives you information about the status of the Sound Bar.

• Sound Bar status
• LED Indications

Using the Remote

1. Soundbar Turns on/off
2. Short press the button to pause and play a music under BT/USB mode; long press to reset BT
3. Skip to previous track in BT/USB mode
4. Select the input modes
5. Short Press the buttons to decrease volume
6. News Mode
7. Music Mode
8. Mute or resume the sound
9. Skip to next track in BT/USB mode
10. Short Press the buttons to increase volume
11. Movie Mode

Install or replace the remote batteries

Battery Type: CR2032 (supplied)

Connect to your TV

There are 2 ways to connect your sound bar to the TV (listed in order that we recommend):Optical(refer to 4A), and AUX (refer to 4b)

Kindly note:
For optical connection ,please change TV audio output to PCM (or SPDIF and optical) and external speaker, otherwise you will get cracking noise or no sound.

Optical

• Step 1, Turn off the sound bar and TV, then connect the sound bar to the TV through the optical cable( need to remove the protective cap of the optical cable when connection).
• Step 2, Turn on the sound bar, press the mode on the sound bar remote, select OPT on the LED display
• Step 3, Turn on the TV, press the home (or menu) on the TV remote, go to TV setting→ audio (sound)→TV speaker–select external speaker (turn off TV speaker),save the setting, then back to audio (sound setting)—select expert setting—digital audio output (or optical) —select PCM (some TV called SPDIF or optical), Save the setting.
• Step 4, Play TV show to test the sound bar.

Important: the TV default audio output is the analog signal and the internal speaker, But please note the optical cable is the digital signal, need to change your TV audio output to a digital optical/PCM signal and external speaker, otherwise the soundbar will output cracking noise sound, pop sound, static sound, or no sound.

Here are several suggestions for most TVs to set OPTICAL(Activate PCM and external speakers only):

Samsung TV

1. Setting→ Sound→ Sound Output→ Turn o TV Speaker or select External Speakers
2. Setting→ Sound→ Expert Setting→ Digital Output Audio Format→ PCM

Vizio TV

1. Setting→ Audio→ TV Speakers→ OFF
2. Setting→ Audio→ Digital Audio Out→ PCM

Sony TV

1. Setting→ Display& Sounds→ Audio Output→ Speakers→ Audio System
2. Setting→ Display& Sounds→ Audio Output→ Digital Audio Out→ PCM
3. Setting→ Display& Sounds→ Audio Output→ Pass Through Mode→ OFF

LG TV

1. All Setting→ Sound→ TV Speakers→ OFF or select External Speakers
2. All Setting→ Sound→ Advance Settings→ Digital Sound Output→ PCM

TCL Roku TV

1. Setting→ Audio→ Audio Out→ Auto
2. Setting→ Audio→ Digital Audio Format→ Select Stereo

TCL TV (Powered by android)

1. TV Setting→ Audio→ TV Speakers→ OFF or select External Speakers
2. TV Setting→ Audio→ Advance Setting→ Digital Audio Out→ Select PCM
3. TV Setting →System →T-Link →Select ON

Hisense Roku TV

1. Setting→ Audio→ TV Speakers→ Select Disabled
2. Setting→ Audio→ Digital Audio Out→ Select Stereo

ONN Roku TV

1. Setting→ Audio→ TV Speakers→ Select Disabled
2. Setting→ Audio→ Digital Audio Format→ Select Stereo

Hisense TV(Powered by android)

1. TV Setting→ Sound→ Speakers→ Select OFF or select External Speakers
2. TV Setting→ Sound→ Advance Setting→ Digital Audio Out→ Select PCM

Sharp TV

1. TV Setting→ Sound→ Advance Audio Setting→ Digital Audio Out→ Select PCM
2. TV Setting→ Sound→ Advance Audio Setting→ TV Speakers→ Select OFF or select External Speakers

Sharp TV(Powered by android)

1. Setting→ Devices Preferences→ Sound→ Digital Output →Select PCM
2. Setting→ Devices Preferences→ Sound→ Speakers →Select External Audio System

Insignia Fire TV & Toshiba Fire TV

1. TV Settings→ Display & Sounds→ Audio Output→ TV speakers→ Select OFF
2. TV Settings→ Display & Sounds→ Audio Output→ Digital Audio Format→ Select PCM

Panasonic TV

1. Menu→ Audio Settings→ Advance Audio→ TV speakers→ Select OFF
2. Menu→ Audio Settings→ Advance Audio→ Digital Audio Out→ Select PCM

Roku TV Stick

1. Setting→ Audio→ Digital Output Format →Select Stereo
2. Setting→ Audio→ Audio Mode→ Select Stereo

Fire TV Stick

1. Settings→ Display & Sounds→ Audio→ Surround Sound→ PCM

Kindly Note: TV settings may differ according to TV models difference, if the listed method can not work, or your TV is not listed, please contact us via service mail: support@wogree.com, or contact the TV manufacturer for help, thank you!

AUX

Here are two ways that you can use the AUX jack to setup a sound bar.

1. use the 3.5mm to 3.5mm cable (supplied) connect the sound bar AUX jack to your TV headphones jack.
2. use the RCA to 3.5mm cable (not supplied) connect the sound bar AUX jack to your TV AUX(L/R, red and white) jack.

Please just choose one way to connect, then follow the below instruction to set up the sound bar:

• Step 1, choose line in cable(3.5 to 3.5mm)or RCA cable connect the sound bar to your TV.
• Step 2, Turn on the sound bar, press the mode on the sound bar remote, select AUX on LED display.
• Step 3, Turn on the TV, press the home (or menu) on the TV remote, go to TV setting→ audio(sound)→TV speaker–select external speaker(turn on TV speaker), save the setting.( For some TVs, please back to audio(sound)→select analog output→ select the “Variable” ,save the setting).
• Step 4, Play TV show to test the sound bar.
  

USB

Connect your USB drive to the USB jack on the Sound bar.
Press mode on the sound bar remote, select USB on the LED display.
Kindly Note: only for USB flash drive to play MP3 music and update firmware, can not compatible with other usb devices.

Pair with your BT device

The initial connection

1. Press mode on the sound bar remote, select BT on the LED display.
2. Turn on BT on the BT device. (see the device’s manual for more information)
3. Select “WOGREE S60” from the device BT list, connect it. When your BT device is connected, the LED will stop flash.
4. Play music files from the connected device via BT, through the Sound bar.

• The sound bar only support one BT device at a time.
• If your device requests a password, enters the default “0000”.
  

Troubleshooting

No Sound|

1. Please check if the sound bar is consistent with the input mode of sound source by following the manual
2. Press the “Volume+” button on the remote or sound bar to volume up
3. Please check the output devices if the output of sound source is working

| Please make sure all the sound bar ports are input ports and all the connected devices are audio output.
---|---|---

No Sound when TV is connected with optical

|

1. Set up the optical output
2. Set up the audio output format–PCM
3. Adjust to optical mode, and the LED will show OPT
4. Please check if the optical is connected with TV effectively 5: Volume up the sound bar

| Please take out the transparent antirust caps on two sides of optical. One side of optical indicates the white lightning when TV is connected well, and then plug the other side of optical into the optical port of sound bar.
Devices can’t connect with BT|

1. Adjust to BT mode, and the LED will show the BT
2. Reboot the cellphone or BT devices, search again
3. Please make sure the sound bar is disconnected with other BT devices, shut off and try again.
4. Please check if there is strong interfering signal around, such as: WIFI, 2.4G; Try to use in other space.
5. Please try to use other BT devices to test if the BT device has problem of its own.

| The BT is only connected with one device, other devices can’t search it when it has connected.
BT connection is unstable|

1. Please check if there is strong interfering signal around, such as: WIFI, 2.4G; Try to use in other space.
2. Reboot the cellphone or BT devices, then reconnect
3. Please make sure there is no obstacle between the sound bar and BT device in case of blocking the signal.
4. Power off the sound bar and then reboot.

| Please make sure there is no signal interference around the product.
The remote is not working|

1. Please check if the positive and negative of battery is right. (There is noted on the battery’s compartment)
2. Please check if the receiving location is blocked under the LED on sound bar.
3. The working distance of remote is 6-8m (empty space)

|
---|---|---
The sound is low or bad|

1. Please make sure if the volume of output device is high.
2. Please try to play with other devices to test if the working device has problem of its own.
3. The product is designed for home, it would be much better if the space is moderate.

| The location of sound bar can affect your experience in some extent.
The sound is inconsistent with the sound of TV| Please set up and shut off the sound of TV| Check the TV’s manual.
Cracking sound or popping sound when play video from Amazon Prime Video, YouTube, HBO, Netflix or other streaming video APPs| This sound bar don’t support Dolby and DTS, please disable the Dolly and DTS, if you do not know how to set, please contact the APP support|

Important Notes About Service
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.

Specifications

• Sound Bar
  2 Full-band speakers

• Inputs
  One 3.5mm, One USB, BT (Wireless), One Optical

• Frequency Response (System)
  50 Hz to 16 Khz

• Compliances
  FCC

• Place of Origin
  China

For more information, please feel free to contact us:
Web: www.wogree.com
Email: support@wogree.com
NOTE: One year warranty, 45 days money back guarantee, lifetime technical support, 100% satisfaction service, please feel free to contact us for any questions.

References

• Wogree Soundbar – wogree

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>