WOGREE S68 Small Sound Bar Speaker System User Guide

WOGREE S68 Small Sound Bar Speaker System

Important Safety Instructions

1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Cleao only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

What’s in the box

Make sure you read all the safety information before you use this product.

Overview

Sound Bar main unit

Sound Bar LED Indicator

The LED indicator on the Sound Bar gives you information about the status of the Sound Bar.

Wall mount your Sound Bar

Required tools:

• Place the soundbar in the desired position and using a spirit level check that the soundbar is level. 1
• Make a light pencil mark on the wall at the top edge of both fixing brackets. The mark should be positioned directly above each bracket. Note the mounting points on the soundbar (one is 147.5mm from the end while the other is 102.5mm from the other end), so you should use the soundbar as a template to get the right mounting positions. 2
• Place the soundbar away from the work area and then mark two fixing points 7mm below the light pencil marks for the screws. These marks should be 360mm apart and level. Before drilling, use a spirit level to check that the fixing points marked are level. 3
• If fixing to a solid masonry wall, use a masonry drill bit, drill holes to a depth of approximately 30mm and insert the wall plugs. Insert the screws into the wall plugs and drive home the screws until the heads stand proud of the wall by about 1 mm.
• If fixing to hollow plasterboard walls, use a drill bit suitable for wood and replace the wall plugs with wall anchors appropriate for the application. Locate the fixing points into wall studs and cross braces where possible. Locate the soundbar onto the screw heads and check that the screws are fully engaged into the keyhole mount before releasing your hold. 5

Install or replace the remote batteries
Battery type: 1.5V AAA Alkaline battery x 2

Using the Remote

1. Turns the Soundbar on and off.
2. Press the button to mute and unmute.
3. Press the buttons to adjust the volume.
4. Press the button to pause and play music. (BT and USB Mode} Hold press reset volume/EQ/3D back to the default state.
5. Press the buttons to select the previous or next music file. (BT and USB Mode)
6. Select the modes.
7. It can adjust the Bass volume in the mode of MUSIC.
8. BT Reset (Press and hold 3 seconds under BT working mode).
9. It can adjust the Treble volume in the mode of MUSIC.
10. Press this button 3D sound on or off (works in MUSIC DIALOG MOVIE EQ mode)
11. Press the button to select the desired music mode: MUSIC, DIALOG, MOVIE.

Connect to your TV

There are 4 ways to connect your sound bar to the TV (listed in order that we recommend): Optical (refer to 5a), LINE IN (refer to 5b), TV ARC (refer to 5c), and AUX (refer to 5d).

Optical

• Step 1, Turn off the sound bar and TV, and connected the sound bar to the TV through the optical cable.
• Step 2, Turn on the sound bar, and press the Input on the sound bar remote, the LED indicator will be White.
• Step 3, Turn on the TV, press the home (or menu) on the TV remote, go to TV sets, audio(sound) –> TV speaker–select external speaker(turn off TV speaker), save the setting, then back to audio(sound setting)—select expert setting—digital audio output(or optical output)–select PCM(some TV called SPDIF or optical), Save the setting.
• Step 4, Play TV show to test the sound bar
  Kindly note: for optical connection, please change TV audio output to PCM(or SPDIF and optical) and external speaker, otherwise you will get cracking noise or no sound.

LINE IN

Here are two ways that you can use the line-in jack to setup up a soundbar.

1. use the supplied 3.5mm to 3.5mm cable (not supplied) connect the soundbar line-in jack to your TV headphones jack.
2. use the supplied RCA to 3.5mm cable connect the sound bar line-in jack to your TV AUX(L/R, red and white) jack.

Please just choose one way to connect, then follow the below instruction to set up the soundbar:

• Step 1 , choose line in cable (3.3mm to 3.5mm ) or RCA cable connect the sound bar to your TV.
• Step 2, Turn on the sound bar, press the Input on the sound bar remote, the LED indicator will be Green.
• Step 3, Turn on the TV, press the home (or menu) on the TV remote, go to TV setting –+audio(sound) –+ TV speaker–select external speaker(turn off TV speaker), save the setting.( For some TVs, please back to audio(sound) -+Select analog output -+Select the “Variable”,save the setting).
• Step 4, Play TV show to test the sound bar.

TV ARC

Connect the Sound Bar with your TV through the TV ARC cable (not supplied).

• Step 1, Turn off the sound bar and TV, connect the sound bar to the TV through ARC audio cable.
• Step 2, Turn on the sound bar, press the Input on the sound bar remote, the LED indicator will be Purple.
• Step 3, Turn on the TV, press the home (or menu) on the TV remote, go to TV setting ->audio(sound) -> TV speaker-­select external speaker(turn off the TV speaker), save the setting, then back to audio(sound setting)–select expert setting—digital audio output—select HDMI-ARC(per some TV, please choose CEC, then activate the ARC), Save the setting.
• Step 4, Play TV show to test the soundbar.

Kindly note: for the TV-ARC connection, please check if the HDM*-CEC feature of your TV is turned on. This feature may be called T-Link, Anynet+, Simplink, BRAVIA Link, Easylink or VIERA Link.

AUX
Connect AUX(L/R) on the sound bar to the AUDIO OUT(Headphone) jack of the TV using the RCA to 3.5mm cable.

Press the “INPUT” button on the remote, and the LED indicator will be Yellow.

• If no sound or echo, set your TV’s audio output to external speaker. Press the home or menu button on the TV remote, go to TV setting — sound — TV speaker — select the external speaker (disable the TV speaker), more detail, please refer to TV manual.
• In this model, the TV’s remote control can adjust the volume. (For some TVs, please press home or menu on the remote go to TV setting — Sound — Analog output — select “Variable”).

USB

• Connect your USB drive to the USB jack on the Soundbar.
• Press the “INPUT” button on the remote and the LED indicator will be baby blue.
• Kindly Note: only for USB flash drive to play MP3 music and update firmware, can not compatible with other usb devices.

Pair with your BT device

The initial connection

1. Press the ” INPUT” button on the remote, the LED indicator will be Blue light flash.
2. Turn on BT on the BT device. (see the device’s manual for more information)
3. Select ” WOGREE S68 ” from the device BT list, and connect it. When your BT device is connected, the LED indicator will be blue light.
4. Play music files from the connected device via BT, though! the Soundbar.

• You cannot connect more than one BT device at a time.
• If your device requests a password enters the default “0000”.

Troubleshooting

Important Notes About Service
Figures and illustrations in this User Manual are provided for reference only and may differ from the actual product appearance.

Specifications

For more information, please follow us:

• Web: www.wogree.com.
• Email: support@wogree.com.

NOTE:
One-year warranty, 45 days money-back guarantee, lifetime technical support, and 100% satisfaction service, please feel free to contact us for any questions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>