Wuhu Youfan E Commerce SSC8 Smart WiFi Indoor Sprinkler Controller User Manual

June 6, 2024
Wuhu Youfan E Commerce

Wuhu Youfan E Commerce SSC8 Smart WiFi Indoor Sprinkler Controller

Wuhu Youfan E Commerce SSC8 Smart WiFi Indoor Sprinkler
Controller

At a Glance

at a glance

Specifications

Input                                                      120V AC 60Hz
Output                                                   AC24V 1 000mA
Controller ratings                                   Input/output: AC 24 V 1 000mA
operating temperature and humility       -10°C~55°C, 10%~90%RH, Non-condensing

Download the app to your Mobile Phone

  1. Search the keyword “Smart Shyion”in APP Store or Google Play to download the App.
  2. Open the app and register an account to log in.

Installation

What you will need?
WiFi Access:2.4Ghz network required
Mobile devices: Requires ios 9.3 or newer or Android 4.0 or newer

  • 1 x Screwdriver
  • 1x Drill
  • 1 x Wire stripper
  • 1x Hammer

When removing the protective cover, reach into the protective cover with your hand, press your fingers against the top and push it out, you can easily take it out .

installation

  1. Select a location
    Choose a location near power and away from direct sunlight. This location should have a good WiFi signal,you can check the signal via a smartphone.

  2. Mount the controller
    Install a screw ( included ) into the wall.Use the expanding anchors ( included ) for plaster, masonry or drywall installations. Hang the controller on the installed screw using the keyhole slot. Level the controller and use the second screw in one of the preformed mounting holes to secure the controller.

  3. Connect valve wires
    Strip about 10mm of insulation from each wire,attach one wire from each valve to a “Common” (COM) terminal and the other wires to a numbered terminal (one wire per terminal).

Note: to prevent damage to the controller, connect only one valve to each terminal.

installation 1

installation 2

Control the Controller to WIFI

  1. Connect your mobile device to the Wi-Fi network that the controller will connect to. Only 2.4G network is supported.
  2. Open the App, tap the add icon “+” at the bottom and select Smart Sprinkler Control device from the list.connect the controller
  3. Press and hold the ►II button for about 5s and release until the WiFi indicator light is rapidly flashing that indicates the controller is ready to configure.
  4. Enter the password of the WIFI network that your mobile device is connected to, then it will start registering the device to the cloud.
  5. Once the device has been added successfully, you will be able to remotely water your lawn from anywhere.

installation 3

Manual Operation

All programming and full functionality of the controller are available in the App.If you needed.there are some basic operations you can perform directly at your controller.

manual operation

TROUBLESHOOTING

troubleshooting 1

troubleshooting 2

FCC Statement

  1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  2. This device may not cause harmful interference.
  3. This device must accept any interference received, including interference that may cause undesired operation.
  4. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequence energy and.if not installed and used in accordance with the instructions.may cause harmful interference to radio communications.However.there is no guarantee that interference will not occur in a particular installation.if this equipmemt does cause harmful interference to radio or television reception.which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an autlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This equipment should be installed and operated with a minumum distance of 20 cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals