Waiv Internet Of Things Technology AIRQM-9 Air Quality Monitor Instructions
- June 6, 2024
- Waiv Internet Of Things Technology
Table of Contents
Air Quality Monitor
AirQM-9 Instruction Manual
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Product Introduce
Face Panel
Specifications:
| Model | AirQM-9 |
|---|---|
| Size | 1506649.2mm (non-include power plug) |
| Net Weight | |
| Input Power | 110~240V-0.1A, 50/60Hz |
| Operation Ambient | Indoor Use Only Temp:-10℃~60℃ Hum: 0-90% non-condensing |
| Network Connection | Wi-Fi IEEE 802.11b/g/n 2.4GHz |
Operations
Setup
Insert the device to the power socket and the display shows a ten-second
countdown. The device starts to work normally when the countdown ends.
Attention:
To ensure the data accuracy of the measurement, please keep the device’s
orientation as the picture and work in a well-ventilated place. on: To ensure
the data accuracy of the measurement, please keep the device’s orientation as
the picture and work in a well-ventilated place.
Configuration Enter Network Configuration Mode
Press the Switching Button for several seconds after power-on, and release the
button after buzzer is on. The Wi-Fi icon should flash slowly in the upper
right corner of the display, then the device enters the network configuration
mode.
Connect the Device with a Mobile phone
Enter WLAN setting of mobile phone, search Wi-Fi ‘airbox_device’ and select.
Enter Network Configuration Interface
After the mobile phone is connected to the device’s Wi-Fi, open the phone
browser and input 192.168.4.1 in the address bar to enter the configuration
interface.
Fill in the Configuration Information
Input Wi-Fi SSID, password, and other network configuration parameters in the
Connect NetWork interface. And click the Config button to finish.
Attentions:
1. Special characters are not allowed when entering the configuration
information.
2. The mark * is a mandatory field, please fill it incorrectly.
3. The last input data will be the default configuration if the nonmandatory
fields are not modified when changing the network connection setting.
Display Description:
Measuring Type Switching
The Display just can show one measurement data only, click the Switching
Button to change the display parameter.
Status Indicator Description:
Attention：
When the measuring value of CO, CO2 or Smo is out of range, the Status
Indicator light up in red and buzzer alarm.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to
correct the interference by one or more of the following measures:
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Statement
To maintain compliance with FCC’s RF exposure guidelines, This equipment
should be installed and operated with a minimum distance of 20cm the radiator
your body. This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>