Asmart Light CLW08E LED Corn Light Instructions

LED Corn Light Instructions

Can not use the electric generator to test the LED lamp.
Please avoid using the led fixture in environments where there is smoke, sulfur, and corrosive substances. But if used in such an environment, make sure the led fixture is well protected by an enclosed lampshade whose dimension is no less than below size, and whose material is either glass or semi-glass, semi-metallic. The surface of the lampshade shall not have any covering which prevents heat dissipation.

Power(W):| 100| 120| | | |
---|---|---|---|---|---|---
Volume(CM)| 442424| 442626| | | |

Product features:

• Single CCT mode, without CCT adjustable function.
• Two dimming options are available for the Single CCT mode 27-120W, continuous dimming, or segmented dimming.
• Can be with a Clear or frosted PC cover.
• Single CCT 27-120W lamp can be with AC100-277V internal driver.
• Motion sensors or PIR sensors are optional for the Single CCT mode 80-120W.
• 12-120W Sealant pouring for whole drive and lamp plastic housing.
• Long lifespan and good heat dissipation. No fan.
• Direct replacement for Metal Halide, Easy Installation.
• Fits many different fixtures to replace traditional lamps.

Application:

Widely used in supermarket, warehouse, garage, home, office, hotel, hospital, school, street, garden, etc.

Installation Instructions:

Warning: Please make sure the power is off before installation.

1. Turn off the power switch.

2. Screw off the CFL or MHL or HPS and so on, see Figure (5) (6).

3. Take out led corn light and screw-on, see Figure (1) (2) (3) (4). Figure (1) (2) (3) (4): AC internal driver,
   (Note: Pls make sure to take off the ballast before installing the led corn light, otherwise, the ballast will produce the resonance of high voltage and makes led corn light breakdown.)

4. If security rope is provided, pls fix the rope on the lamp with your hand then fix the wire of another end on the shell, see Figure(2) (4).

5. Lamp CCT and dimming can be adjusted after removing the top plastic cover with a screwdriver. Figure(5) (8)

6. Turn on the power switch. ( Finished!)

CCT adjustable and dimming mode diagram：

1. Continuous dimming
2. Segmented dimming

Installation of motion sensor or PIR sensor

It could be easily installed by using a straight screwdriver. Use a flat-blade screwdriver to unscrew the plug and remove the plug. And then, adjust the lamp power to the maximum (otherwise the sensor will act abnormally).
Install motion sensor or PIR sensor and tighten it.
Note: the motion sensor has no dialing code, and remote control is needed for adjustment.
Please refer to the instruction for remote control adjustment. WARNING:
WARNING – Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaries’ electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
WARNING – Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION. PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH THE APPLICABLE AND APPROPRIATE ELECTRICAL CODES.
THE INSTALLATION GUIDE DOES NOT SUPERSEDE LOCAL OR NATIONAL REGULATIONS FOR ELECTRICAL INSTALLATIONS.
SUITABLE FOR DAMP LOCATIONS.
ADDED WEIGHT OF THE DEVICE MAY CAUSE INSTABILITY OF A FREE-STANDING PORTABLE LUMINAIRE.
USE ONLY WITH A PORTABLE TABLE LAMP THAT IS PROVIDED WITH A SHADE.
USE IN PORTABLE TABLE LAMPS IN WHICH THE DISTANCE FROM THE BOTTOM OF THE BASE TO THE TOP OF THE LAMP HOLDER DOES NOT EXCEED THREE (3) TIMES THE MINIMUM BASE DIAMETER.
THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS” or “NOT FOR EMERGENCY LIGHTING.
MIN. LAMP COMPARTMENT DIMENSIONS(L x W x H)

Model Number| Minimum Lamp Compartment
Dimension(mm)(H)x(L)x(W)
---|---
AST-CLW08E-054WXYA1-adck| 420 X 210 X 210
AST-CLW08E-063WXYA1-adck| 420 X 230 X 230
AST-CLW08E-080WXYZA1-adbck| 420 X 230 X 230
AST-CLW08E-100WXYZA1-adbck| 440 X 240 X 240
AST-CLW08E-120WXYZA1-adbck| 440 X 260 X 260

FCC Statement ：
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
The distance between user and products should be no less than 20cm
IC STATEMENT
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>