Xiamen Hanin Electronic Technology HN-3378SR-000R Handheld Wireless Barcode Scanner Instruction Manual

Handheld Wireless Barcode Scanner
HN 3378SR-000R
Instruction Manual

Appearance

① Sound Hole
⑥ Power off Button| ② Scan Window
③ Scan Button
⑦ Charging contacts (It is used with the
communication charging base)
---|---

Communication Charging Base

④ Indicator
⑧ Indicator| ⑤ Type-C Cable Interface
⑨ RJ45 Cable Interface
---|---

LED Indicator

Communication Charging Base

How to Use the Communication Charging Base

1. Connect one end of the cable(RJ45) to the charging base.
2. Connect the other end of the cable to the HOST.
3. Put the scanner into the charging base.

Power on/off and Restart

• Power on:
  1. After it is connected to the host, it will be automatically powered on.
  2. When it is not connected to the USB cable, you can press and hold the button to power on.

• Power off:
  1. Press and hold for 15s to power off.
  2. It will be automatically powered off without any touch after 15mins.

• Restart:
  If the scanner crashes or does not respond, you can insert the clip into the switch key in the bottom, then press the scanning button to restart the scanner.

Maintenance

• The reading window must be kept clean.
• Avoid hard and rough objects to scratch the reading window.
• Remove the stains from the window with a brush.
• Please use a soft cloth to clean the window, such as a glasses cloth.
• Do not spray any liquid on the window.
• Do not use any cleaner other than cleaning water.

Buzzer

Restore Factory Default

Scan the barcode to restore all settings to the factory default state.

Note: Please use the “factory reset” function carefully. After reading this barcode, the current parameter settngs will be lost and replaced with the factory default values.

Interface Settings

The scanner can communicate with the host by RS-232 serial port or USB port. The user can switch to the corresponding interface by replacing the data line and scanning the corresponding barcode below.

Bluetooth Settings

Set the Bluetooth power on/off time

Scanning Mode Setting

Scan mode settings by scanning the barcode below.

Common Problem(FAQ)

Q: There are some barcodes that can not be scanned.
A：
a) Firstly, check the barcode type, open the barcode function; if it is verified, try to turn off.
b) Unable to know the barcode type, then set all barcodes allowed to be recognized.
Q: The barcode data is incorrect.
A：
Check the error display of barcodes (all barcodes errors or specific barcode error)
Q: Barcode can be recognized but not displayed.
A：
Firstly, confirm the scanner whether it is in the Bluetooth transferring mode. If yes, the scanner has been connected to the PC.
Q： Aiming Light and LED are not bright.
A：
a) Check whether the device is powered on.
b) Re-plug the data cable.

State

• Our company does not assume any responsibility for losses caused by natural disasters (such as earthquakes, floods, etc.) that exceed our scope of responsibility.
• In any case, our company does not assume any responsibility for losses caused by using this product, such as loss of profits, loss of reputation, business interruption, loss or change of stored data, and any special, unexpected, associated, or intermittent losses caused by the above.
• Our company does not assume responsibility for the losses caused by due to improper use of hardware or software not specified by our company.
• Our company does not provide any form of warranty or technical support for the information, data, files, other products, services obtained through the use of this product, and does not assume any responsibility for the use of the above description by users.
• Our company does not take any form of guarantee for third-party software used by this product.
• Due to the continuous improvement of the products, the operation and common problems of the models described in the manual are mainly based on actual machines. And it may be changed without notice.

FCC Warning

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including int reference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC ID：2AUTE-3378

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>