rainus InforTab-Ready Electronic Shelf Label System User Manual
- June 6, 2024
- rainus
Table of Contents
INFORTAP-READY
USER MANUAL
Version 2.0
ESL Introduction
Electronic Shelf Label System (ESL) provides product information by replacing a series of tasks which is printing attaching price, and merchandise information in the paper to the electronic display.
InforTab-Ready Preparation
In order to set and monitor InforTab-Ready, a Personal computer with a network is required.
InforTab-Ready Composition
Compositions of InforTab-Ready are,
- 1.54 Inch InforTab(R154) 1EA
- 2.13 Inch InforTab(R213) 1EA
- 2.90 Inch InforTab(R290) 1EA
- 4.20 Inch InforTab(R420) 1EA
- 7.50 Inch InforTab(R750) 1EA
- Gateway 1EA, Antenna 4EA
- 5V Power cable 1EA, LAN cable 1EA
- Remote Control 1EA, UnlockTool 1EA
InforTab-Ready Preparation
Network, UI setting
PC Network setting
For connecting Gateway and User.
Gateway IP is set by 192.168.220.236 in advance.
Setting a PC network fixed IP is required. For instance,
192.168.220.45 can be set as PC network IP.
To change PC network IP, Control Panel > Network Internet > Network settings >
Ethernet Properties > Internet Protocol version 4(TCP/Pv4) > Use following IP
Confirm
Connect InforTap UI
- Plugin Gateway with power cable, and connect to PC by LAN cable. If all of these are connected properly, Red, Green and Blue lights will go on.
- Run internet browser in PC and write Gateway fixed IP (192.168.220.236) on the address bar.
- If connected properly, the InforTab UI screen will appear.
- Change Password in Menu ‘Account Setting’. The initial ID is ‘admin’ and the password is ‘1234’.
InforTab Assign
InforTab and specific products work together showing the product information.
This system is operated by the ‘Assign’ process.
Assign confirmatory
InforTab-Ready’s 4 InforTabs are already assigned. Assigned InforTap in
Gateway can be verified by ‘Status > Tag’ in UI.
InforTap Mac Address check
InforTab Mac address is displayed as a barcode when you press ‘>’ or ‘<’
buttons of the remote controller in front of the tag.
Delete 2 digits and leave 4 digits from the back in order to search Mac
address in UI.
For further more explanation, if Mac address is ‘78E980FFFE004C4B’, can be
searched by ‘004C’.
Assign: Connect InforTab and Product in Gateway.
Update: To change product information with assignedInforTab
InfoTab Update
Confirm InfoTab Layout
InforTap Layout can be found at the ‘Product Update’ menu.
: Layout choice
: Layout look preview
The layout is the location of information and design which shows in tag
display. It can be adjusted in ‘Layout Designer’.
We provide ‘Layout Designer Manual’ in addition which guides how to use
‘Layout Designer’.
Product information Update
- Choose proper Layout and put appropriate InforTab information.
- Check the square box on the right side and click ‘Update’ on the bottom side of the page.
- Press ‘Okay’ to confirm the procedure.
InfoTab Update
Confirm InfoTab Update Result
After the update, the page automatically moves to the ‘Task’ menu in UI and it is available to check update status in real-time.
InforTab update generally completes in 5 minutes, but the time it can be delayed by network circumstances.
To make InforTab update on purpose, Remote Controller.
After flicker light, the update process will be operated when pressing the ‘R’ button of the remote controller.
InforTab De-Assign, Re-Assign
InforTab Re-Assign
If need to update back, ‘Re-Assign’ work is required. Choose ‘Status > Tag’ Menu in UI and click ‘Assign’.
After clicking the ‘Assign’ button, write down the InforTab Mac address and product code. Then press the ‘Save’ to make the procedure complete.
Wireless Network Circumstance
InforTap system uses two channels of wireless 2.4GHz so that it can affect
updating speed of InforTab according to the wireless network environment.
Wireless Channel
According to wireless circumstances, the InforTab system may not be
operated properly by influence with other wireless
instruments. In this case, changing the channel is required. In order to change the channel, click the ‘Gateway Config’ menu in UI and press the ‘Setting’ Icon on the right side of the page.
Date channel, Event channel are composited with 11~26 channels..
Begin with 11 channels and go up until finding a proper one.
Press the ‘Save’ button to confirm the channel.
Information to user
WARNING: This equipment may generate or use radiofrequency energy.
Changes or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications, However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
-IMPORTANT NOTE: FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>