Zhejiang Pdw Industrial BCS1A1 Programmed TOYOTA TPMS Sensor User Manual
- June 6, 2024
- Zhejiang Pdw Industrial
Table of Contents
Zhejiang Pdw Industrial BCS1A1 Programmed TOYOTA TPMS Sensor User Manual
SPECIFICATION
Product Name
|
Programmed TOYOTA TPMS Sensor BCS1A1 (4pcs
---|---
Product Model
| BCS1A1
Pressure Monitoring Range|
0 ~ 8Bar (0 ~ 116PSI)
Operating Temperature
| -40 OC ~ 125 OC (-40 OF ~ 257 OF)
Battery Life|
4 ~ 6years
Remark
- This sensor can detect real time tire pressure & temperature;
- According to different vehicle models, the dashboard or infotainment may show pressure, pressure & temperature, or warning icon in time of data beyond the “safety range” has been detected. However, what is shown is set by the vehicle factory & cannot be changed. For example, if the infotainment shows tire pressure only with its original sensors, when yo replace the sensors, the information shown on the infotainment is also tire pressure only.
Before Installation
Make sure that –
- Your car model & year are within the “Car Models Supported ” listed at the bottom;
- The sensor frequency is the same as what is indicated on the original sensors or vehicle user’s manual;
Installation
- Only professionals are authorized to install the sensors, who can be found in Every tire stores, Every car service workshops, or Most of car parts stores;
- Demount the tire & wheel from a vehicle;
- Demount the tire from the wheel;
- Replace the old sensor/valve with our new sensor –
- Sensors with metallic valve: disassemble the cap, gasket & nut->install the valve through the wheel valve hole->put on the gasket->fasten the nut->screw in the cap.
- Sensor with rubber valve: unscrew the cap->snap in the valve through the wheel valve hole->screw in the cap.
- Mount the tire on the wheel;
- Mount the tire & wheel on the vehicle.
After Installation
Pairing the sensors with the infotainment is necessary to display tire information on the latter.
- Step 1: Scan each newly installed sensor ID in the the sequence of “Front Left – Front Right – Rear Right – Rear Left” through a scan tool (for example, an Ateq Tool);
- Step 2: Turn the ignition to “ON” with the engine off;
- Step 3: Connect the scan tool to the OBDII port and upload the sensor IDs;
- Step 4: Turn the ignition to “OFF” to re-scan each sensor for pairing;
- Step 5: Drive the vehicle for at least 10 minutes with an even speed of 30mph or above to make sure no warning information is displayed.
Car Models Supported
Lexus :
- CT200h 2011-2016
- ES350 2007-2012
- GS300 2006
- GS350 2007-2011
- GS430 2007
- GS450h 2007-2011
- GS460 2008-2011
- GX460 2010-2016
- GX470 2005-2009
- IS F 2008-2014
- IS250 2006-2015
- IS350 2006-2015
- LX470 2004-2007
- LX570 2008-2011, 2013-2015
- RX330 2006
- RX350 2007-2015
- RX400h 2006-2008
- RX450h 2010-2015
- SC430 2007-2010
Toyota:
- Scion iQ 2012-2015
- Scion tC 2010-2016
- Scion xB 2008-2015
- Scion xD 2008-2014
- 4Runner 2004-2016
- Avalon 2007-2012
- Camry 2007-2011
- Corolla 2007-2013
- FJ Cruiser 2007-2014
- Highlander 2008-2013
- Land Cruiser 2005-2011, 2013-2015
- Matrix 2007-2013
- Prius 2006-2015
- Prius Plug-In 2014-2015
- Prius V 2012-2016
- RAV4 2006-2012
- Sequoia 2005-2007
- Solara 2007-2008
- Tacoma 2006-2015
- Tundra 2005-2006
- Venza 2009-2015
FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits aredesigned to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
One year of the guarantee period is provided with the conditions as following:
- In addition to the claims under the law and/or contract of sale which arise from material defects, the rights arising from this guarantee are granted by the seller to the customer.
- The product is guaranteed to be free of any defects.
Parts that are subject to wear and tear such as batteries, or battery cells are not included in this
Guarantee
The guarantee is excluded if
- The product has been misused or treated carelessly,
- The product has been damaged due to excessive stress, incorrect use or external influence,
- The defect has been caused by failure to observe the operating instructions,
- A repair or a repair attempt has been carried out by personnel other than that of an authorized point of service.
- The guarantee period shall commence at the time of delivery of the product from the seller to the purchaser.
- The place of purchase and the date of delivery shall be proven by submitting proof of purchase, for example, the sales receipt, invoice, delivery note or similar document.
- Any defects that occur during the guarantee period should be submitted to the authorized point of service within 2 weeks since they happened. The defect will be remedied by delivery a product identical in construction. Further claims of the customer arising from this guarantee, particularly claims for reimbursement of expenses, reduction, compensation of damages or the right of withdrawal, shall be excluded.
- The guarantee period shall not be extended if services are performed under the terms of the guarantee.
- The parts replaced when carrying out the repairs under warranty or the product retained in case of replacement delivery shall no longer be the property of the customers’ or dealers’.
- If our customer services are called upon without due cause, the costs incurred will be charged to the customer.
- In case any defects occur, please contact your dealer or the service center in your country.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>