RAYTAC MDBT42Q-VE Bluetooth Module User Manual
- June 6, 2024
- RAYTAC
Table of Contents
RAYTAC MDBT42Q-VE Bluetooth Module
Since this module is not sold to general end users directly, there is no user
manual of module. For the details about this module, please refer to the
specification sheet of module.
This module should be installed in the host device according to the interface
specification.
installation procedure
The following information must be indicated on the host device of this module;
[for FCC] Contains Transmitter Module FCC ID: 2A2XGMDBT42Q-VE
For IC
Contains IC: 27461- MDBT42QVE
Specificaiton
Operation Conditions
The following statements must be described on the user manual of the host device of this module;
For FCC
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE).
For IC
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
This radio transmitter (IC:27461- MDBT42QVE) has been approved by Industry
Canada to operate with the antenna types listed below with the maximum
permissible gain indicated. Antenna types not included in this list, having a
gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
Antenna type: PCB Gain: -5.36597 dBi
The radiated output power of the Wireless Device is below the Innovation,
Science and Economic Development Canada radio frequency exposure limits. The
Wireless Device should be used in such a manner such that the potential for
human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF
Exposure limits under portable exposure conditions. (antennas are less than 20
cm of a person’s body).
FCC warning statement
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
RF exposure warning
The modular complies with FCC RF exposure limits set forth for an uncontrolled
environment. The equipment must not be co-located or operating in conjunction
with any other antenna or transmitter.
End Product Labeling
If the FCC identification number is not visible when the module is installed
inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains FCC ID:
2A2XGMDBT42Q-VE” and “Contains IC: 27461- MDBT42QVE “
Information for the OEMs and Integrators
The following statement must be included with all versions of this document
supplied to an OEM or integrator, but should not be distributed to the end
user.
- This device is intended for OEM integrators only.
- Please see the full Grant of Equipment document for other restrictions.
ISED warning statement
Canada, Innovation, Science and Economic Development Canada (ISED) Notices
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Innovation,
Science and Economic Development Canada radio frequency exposure limits. The
Wireless Device should be used in such a manner such that the potential for
human contact during normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF
Exposure limits under portable exposure conditions. (antennas are less than 20
cm of a person’s body).
KDB996369 D03 Requirements
List of applicable FCC rules
This module meets all the requirements of FCC part 15.247
Summarize the specific operational use conditions
This module is a Bluetooth Module with built-in Bluetooth V4.2 transceiver.
Operation frequency: 2402-2480MHz
The Module Antenna type is PCB antenna with a maximum gain of -5.36597dBi.
Limited module procedures
Not applicable. The module is a Single module and complies with the
requirement of FCC Part 15.212. 2.5 Trace antenna designs
No, this module is without trance antenna designs, the module use fixed-length
PCB antenna.
RF exposure considerations
The module must be installed in the host equipment such that at least 20cm is
maintained between the antenna and users’ body.
Antennas
The Module antenna specification is as follows:
Label and compliance information
The final end product must be labeled in a visible area with the following:
“Contains FCC ID: 2A2XGMDBT42Q-VE”.
Information on test modes and additional testing requirements
The Host manufacturer must perform a test of radiated & conducted emission and
spurious emission, etc according to the actual test modes for a stand-alone
modular transmitter in a host, as well as for multiple simultaneously
transmitting modules or other transmitters in a host product. Only when all
the test results of test modes comply with FCC requirements, then the end
product can be sold legally.
Additional testing, Part 15 Subpart B disclaimer
The modular transmitter is only FCC authorized for FCC Part 15 Subpart C
15.247 & 15.209 and that the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the
modular transmitter grant of certification. If the grantee markets their
product as being Part 15 Subpart B compliant (when it also contains
unintentional-radiator digital circuity), then the grantee shall provide a
notice stating that the final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>