JCB TH52002C Jack Stand User Manual

JCB TH52002C Jack Stand

Product Information

Specifications

• 2 Tonnes Jack Stand – Safe working load of 2 tonnes per pair
• 3 Tonnes Jack Stand – Safe working load of 3 tonnes per pair
• 6 Tonnes Jack Stand – Safe working load of 6 tonnes per pair

Product Usage Instructions

Introduction
For your safety, read the manual before using the lifting equipment. Ensure understanding of operation and safety procedures. Retain the manual for future reference.

Safety Precautions

1. Read and fully understand instruction manuals before use.
2. Do not exceed the rated safe working load.
3. Check the vehicle owner’s manual for gross vehicle weight.
4. Use only one pair of stands.
5. Avoid body parts near the jack and vehicle when positioning stands.
6. Support the lifted vehicle immediately with jack stands.
7. Never work under a vehicle without using jack stands.
8. The place stands on solid, even ground with wheels chocked, vehicle in gear, and handbrake engaged.
9. Ensure the load is centered and secure on the stand-top saddle.
10. Locate each stand under a strong, stable point on the vehicle.
11. Check vehicle jacking points for good condition.

FAQ

• Q: Can I use the jack stands on uneven ground?
  A: No, it is recommended to use the jack stands on solid, even, and level ground to ensure stability and safety.

• Q: How many stands should I use at a time?
  A: Always use jack stands in pairs as specified for each model to distribute the weight evenly and prevent accidents.

• Q: What should I do if I exceed the safe working load?
  A: Never overload the jack stands beyond the specified safe working load to avoid serious injury or damage. Consult a qualified mechanic if unsure.

1. 2 TONNES JACK STAND
   Safe working load of 2 tonnes per pair – must be used in pairs.

2. 3 TONNES JACK STAND
   A safe working load of 3 tonnes per pair – must be used in pairs.

3. 6 TONNES JACK STAND
   A safe working load of 6 tonnes per pair – must be used in pairs.

GENERAL WARNINGS & DISPOSAL

• To reduce the risk of injury, the user must read the instruction manual.
• This symbol is used throughout this manual to warn the user about potential risks. Please read & understand these sections before using the device.
• Caution! Wear ear-muffs. The impact of noise can cause hearing damage.
• Caution! Wear protective safety gloves.
• Caution! Wear safety goggles. Sparks generated during working or splinters, chips, and dust emitted by the device can cause loss of sight. wood and other materials. Never use the device to work on any materials containing asbestos!
• Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos!

The month and year of manufacture can be found within the product serial number e.g. MMYYPPPAXXXXX. Where production month (MM) and production year (YY) are included.

INTRODUCTION

For your safety, please read this manual before using any lifting equipment ensuring you fully understand its operation and the safety procedures to be observed. Ensure this manual is retained for future reference and that new users of this product read and understand the content before they use the product.

SAFETY PRECAUTIONS

WARNING!
Failure to comply with these instructions can cause serious injury and damage to the vehicle. If you are in any way unsure, do not attempt to use this product and consult a qualified mechanic.

1. Read and understand instruction manuals fully before use. Use only as specified.
2. Never overload these jack stands by exceeding the rated safe working load.
3. Check the vehicle owner’s manual for gross vehicle weight.
4. Use no more than one pair of stands.
5. Ensure all body parts are kept clear of the jack and vehicle when positioning and removing the jack stands.
6. After lifting the vehicle, support immediately with properly rated jack stands.
7. Never work on or under a vehicle without using properly rated jack stands.
8. Only use on solid, even, and level ground with the wheels chocked, the vehicle in gear, and its handbrake on.
9. Always ensure that the load is centered and secure on the jack stand top saddle. Off-centre loads can become unstable and slip resulting in possible damage or injury.
10. Ensure that each stand is securely located under a strong, stable point on the vehicle: consult the vehicle owner’s manual for guidance.
11. Ensure vehicle jacking and support points are in good, sound condition with no corrosion, etc.
12. Do not attempt to move or dolly the vehicle whilst on the jack stands or jack.
13. Do not attempt to modify these jack stands in any way.
14. Upper and lower columns are to be used as a pair as supplied.
15. Do not attempt to use it if you suspect a fault.
16. Do not start the vehicle in its raised position.
17. Do not attempt to enter the vehicle and ensure all passengers are out of the vehicle when using this product.
18. Take care when using a three-wheeled vehicle or trailer.

PARTS OF THE JACK STAND

1. RATCHET BAR
2. BASE FRAME
3. LOCKING PIN
4. LOCKING PAWL(STOPPER)
5. LOCKING TAB
6. LOCKING HANDLE

Visual inspection should be made before each use of the jack stands. Check for cracked welds and damaged, lost, or missing parts. Any jack stands that appear to be damaged in any way, are found to be badly worn, operate abnormally, or have been subjected to an abnormal load or shock MUST NOT BE USED.

MAINTENANCE

Periodically inspect each stand. Ensure all parts move freely. Do not apply oil or grease to any part of this product. If rust appears, sand the affected area and cover it with suitable utility paint.

Storage
Store stands in an upright position in a clean, dry area.

SPECIFICATIONS

All dimensions are approximate. Images are for illustration purposes only.

GUARANTEE
This item is covered by our three-year Quality Guarantee. In the unlikely event that it develops a fault within this period, we will replace it.

OPERATING INSTRUCTIONS

TO SUPPORT VEHICLE

1. Pull the upper column out from the lower column.
2. Insert the locating pin through the holes in both upper and lower columns.
3. Secure the locating pin by inserting the clip pin into it.
4. Carefully position the jack stands so that the load will contact the center of the top saddle.
5. Always use jack stands in pairs and only on those parts of the vehicle that can support the load. Please consult the vehicle owner’s manual for the lift and support points.

NOTE
The stands must only be positioned on a hard-level surface when operational. The rated load of 2/3/6 Tons (TH52002C / TH53003E/ TH56002A) per pair must not be exceeded under any circumstances. Centre load on the top saddle. Use as a matched pair to support one end of a vehicle only.

TO LOWER LOAD

1. Raise the vehicle clear of stands.
2. Carefully lower the stands to the lowest position.
3. Remove stands then carefully lower the vehicle to the ground.
4. Ensure that all tools, equipment, and personnel are clear of the vehicle before lowering the load.

All dimensions are approximate. Images are for illustration purposes only.

WARRANTY STATEMENT

JCB Power Tools are guaranteed against manufacturing defects for up to 3 years from the date of purchase

• Warranty cover commences from the date of purchase on the retail sales receipt and is valid only for JCB Tools products bearing the CE and UKCA mark and a visible serial number.
  In the unlikely event your JCB Tool is subject to a manufacturing fault within the warranty period, JCB Tools may repair the product by replacing defective parts free of charge at our discretion. In the event parts are irreplaceable JCB

• Tools may replace your product free of charge. The original product will remain the property of JCB Tools in this situation.

The above repair or replacement of products will be undertaken to provide that:

• The product has been subject to fair wear and tear only.
• The product has not been subject to accidental or cosmetic damage.
• The product has not been misused and has been used only by the instruction manual provided.
• The product has not been subject to overload or insufficient servicing and maintenance.
• The product has not been subject to any abnormal environmental conditions or inappropriate operating conditions.
• Repairs have not been attempted by an ununauthorizederson and no modifications have been made to the product.
• Repairs have not been undertaken using non-genuine spare parts.

JCB Tools used for Hire Fleets or as part of B2B and Service Contracts are not covered by these terms and conditions.

JCB Tools 3 Year Warranty excludes the following (where applicable):

• Components normally subject to wear such as carbon brushes.
• Batteries, Chucks, and Chargers.
• Accessories and consumable items.
• Cases and tool storage products.

If your product develops a fault within 30 days of purchase, return it to the retailer where it was purchased together with your sales receipt. If a product develops a fault after 30 days a warranty claim must be submitted.

JCB TOOLS WILL NOT BE LIABLE FOR ANY INJURIES OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT.

EU IMPORTER:
TRADE HOUSE FORSAGE INSTRUMENT POL SP.Z.O.O.
UL GRODECKA 1A
15-561 BIALYSTOK
POLAND.

DOWNLOAD YOUR INSTRUCTION MANUAL

Documents / Resources

| JCB TH52002C Jack Stand [pdf] User Manual
TH52002C Jack Stand, TH52002C, Jack Stand, Stand
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>