Ningbo Zmjh Sanitary Technology A201S Smart Toilet Seat Instruction Manual

Ningbo Zmjh Sanitary Technology A201S Smart Toilet Seat

Components

Accessories

| Name| Quota
---|---|---
A| Three-way valve| 1
B| PE pipe| 1
C| Screw| 2
D| Steel disc| 2
| Name| Quota
---|---|---
E| Mounting base| 1
F| Anchoring rubber| 2
G| Gasket| 2
| |

Installation ways

Precaution before installation

1. Ensure that the water pressure range of the inlet is between 0.05-0.75Mpa.
2. Be sure to use the original accessories and consumables.
3. Please do not switch on the power until the installation is completed to avoid failure.

Method of mounting base

1. Draw the mounting base from the machine.
2. lnstall the accessories as shown in the diagram

Connection of external water pipes

1. Close the Angle valve and cut off the water.
2. Connect Three-way valve’s end with the upper water pipe of the toilet tank.
3. Connect the smallest end of the three-way valve with PE pipe,
4. Connect the other end of the PE pipe with the inlet hole of the machine.
5. Open the Angle valve to supply water.
6. Make sure all connections are free of water.

Installation and removal

1. Push with two hands when install the machine onto the toilet, and make sure the installation is in place .
2. Pull outward with two hands when separate the machine from the toilet.

Pilot run

Tips : the spraying time will be delayed by 5-10 seconds for the first time using after installation which is normal phenomenon,not a fault.

For operation

1. Connect the power plug to the socket of 110V/220V voltage.At this time, the floodlight and water temperature light flash.
2. Turn on the water source, and the water temperature light flashes. After 30 seconds, the water temperature light stops flashing and stays on, indicating that the machine has completed the self-test.

Function confirm
onfirm the functions accroding to the instructions.

Cleaning method

1. When no one is seating on the seat, press BIDE T/CLEANING button, spray rod stretchs, wash the nozzle.
2. Clean with toothbrush or soft cloth.After cleaning, press the STOP button to return the spray rod.

Maintenance

A drainage when not in use for a long time

1. Please unplug the power supply
2. Turn off the water supply
3. Pull the machine outward from the toilet
4. Screw out the WATER SCREW( the positon indicated on the diagram) to drain the water
5. Tighten the WATER SCREW and replace the machine

External body cleaning method

1. Main surface should be wiped with sponge or soft dishcloth or the dishcloth with sticky neutral detergent.
2. Note: do not use diluent, light gasoline, detergent or chemical to wipe, do not use pesticides, aromatic agents, deodorant.,etc.

Please follow the safety iinformation below

• It away from wet place and avoid being showered
• Make sure the voltage is appropriate
• Please use the plug-in whose load is over 1400W
• If the power line is damaged, please inform the manufacturer to renew it
• Please use the new pipe attached in the product
• Self-disassembly or Self-repair are forbidden
• Leaving water or detergent on the product or plug is forbidden, in case of accident or breakdown
• In case of accident, do not touch the plug with wet hands
• Ensure the water is pure and clean

Function introduction

ZMA201S

WARNING

1. Don’t use the lacquer thinner,gasoline,medicine,medicine,detergent or pesticide to clean this product.
2. Don’t put any aromatic or medicine in water tank.
3. When sitting on this smart toilet for a long period of time,please regulate the seat temperature to the lower grade.
4. ln case the product is electrified,but no water was supplied to it,don’t place it upside down, otherwise it may result in troubles of heating pipe.
5. When the product is used by persons(including children)with body,sensory,mental deficiency, or lack of common sense,please pay your attention and prevent them from low temperature burning.
6. lt’s strictly prohibited to step on the cover plate,seat ring,or operation panel,it’s not very suitable for children to use it.
7. Cables and sockets used in the house must meet the requirements of national standards, all lines must be grounded reliably.It’s strictly prohibited to use the patch board with two-hole or insufficent powe r to work as the exension line.

This product si prohibited in the high temperature or place in storage and use of flamable and explosive.

Self-trouble-removal\Technical parameter

Insert the power plug into the socket
Pull out the power plug from the socket and insert it again
No water or a little| Make sure the water supply is normal and the water gauge is open| Ensure the water supply
Is working normally
If the nozzle is blocked| Clean the nozzle by toothbrush
Leakage of water| Inspect all the joint of pipes| Buck up all the joint of pipes
Cold water or cold seat| Check the states of product| Adjust the temp.of water and seat to higher levels
Specifications| AC llOV 50Hz 1500W
---|---

Water

supply

| Way| connect to water pipe
prWes.aseurre| 0.05-0.75Mpa
Cleaning| Watercimount

offemininewash

| 0.7L/min
Water amount

offemininewash

| 0.85L/min
Temp.ofwater| 3levels(IOW M”OIUM HIGH)
Heating power| 1500W
Sa’ety protection| TDS/water temperature sensor/WAT

Ileater

| Temp.ofscat| 3 levels(LOW-McDIUM-HIGH)
Heating power| sow
Safety protection| TDS/seat tempe-ature sensor/thermal cuto’f

Warm air dry

| Temp of air| 3levels(LOW-McDIUM-HIGH)
Heating power| -now
Safety protection| TDS/thermal cutoff
Other safety

protection

| Leakage protective plug| We”tgh| 5.8Kg
Prcductdass| Handrail operation| Length of wire| 15m
Dimension| (ZMA2015)510’460’14Dmm / [Z MA201DS)510’380’140mm

coRenmtorotel parameter

| TX

RX

| DC 3Vfrom battery

AC 100-240V 50/60Hz

frequency| 433M Ilz

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio comm uni cations. However, there is no guarantee that interference will not occur in a particular installation. If th is equipment does ca use harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna .
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device com plies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition, compliance with exposure req u lrements.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>