Dongguan Chuanglong Electronics TAC-134 Magnetic Fast Wireless Charging Holder Instructions
- June 6, 2024
- Dongguan Chuanglong Electronics
Table of Contents
TAC-134 Magnetic Fast Wireless Charging Holder
Magnetic Fast Wireless Charging Holder Instructions
Please read the instructions carefully before using. Pictures are for
reference only, Specifications are subject to the physical product
Install instructions:
1. Insert the adjuster into the ball joint adapter.
2. Insert the ball into the socket at the back of bracket, turn the adjuster
to tighten.
What is included:
Magnetic Fast Wireless Charging Holder X 1
Air vent mount X 1
USB cable X 1
Install instructions:
3. Insert the mount directly into the car air vent blade, set the locking
switch to proper position.
4. Connect the charging cable to the charging interface.
Features:
Car holder with wireless charging fuction, charges your phone conveniently
when driving. Power output 5W/7.5W/10W/15W, compatible with all phones with QI
standard.
Custom made magnet array, precisely compatible for iPhone 12 series. Full 360
degrees rotation for perfect viewing angle. Start charging once as the phone
contact with the holder, no need cable anymore.
Adjustable foot support makes easy to align to the charging center.
Parameters: Wireless Charging Holder
Easy touch button to open the clamps
62-106mm
Compatible devices:
Work well with: iPhone 12, iPhone12 Pro Max, iPhone12 Pro, iPhone12 mini
Samsung Note 8, Note 9, iPhone XS MAS, Huawei P30 Pro, MIUI9, Samsung S10+,
iPhone 8PLus, Samsung S9+, Samsung S8+, iPhone XR, Samsung S10, Samsung
S7edge, Samsung S8, iPhone XS, iPhone X, Samsung S9, iPhone 8, iPhone 11,
iPhone SE, Samsung S21, Samsung S20
Also work with all other Qi enabled devices.
Qi disabled devices with wireless receiver or wireless charging case. Require
receiver compliant with WPC Qi standard to match).
Compatible with MagSafe slim phone cover thickness within 4mm
Charging Indicator : Turn red when charging
Type C charging interface
iP 12 Pro Max iP 12(pro) iP 12mini
21mm
Alignment sticker:
To charge effectively, the foot support should be adjusted to align the phone
receiving coil to the charging center.
1.8-2.5mm
Parameters:
Air Vent Mount
There are three levels of locking for different size AC vent blades.
Loose
First position
2.5-3.5mm
Second position
Third position
Within 1.8mm
Product specification:
Wireless Charging Holder
Input voltage 5V/9V/12V
Input current 2A
Output power 5W/7.5W/10W/15W Max
Frequency
110-205KHZ
FCC ID
2APCQ-TAC-134
LED Mode:
Working state
Power transfer
Standby mode Charging FOD Warning Charge complete
LED light color Red,blue,red blue light turn on by turns for once,then off
Light off Red light keeps on Red light keeps flashing Red light keeps on
Install instructions:
Press button
5. Press the release button to release the clamp arms, adjust the foot
support to fit your phone size.
6. Place your device into the bracket and press the clamp arm to lock it
tightly.
Attentions:
1. Please use the product correctly according instructions.
2. Please do not disassemble the product or throw it to fire and water, to
avoid leakage that caused by electrical short circuit.
3. Please do not use wireless charger in high temperature, wet, corrosive
environment, to avoid leakage that caused by damaged circuit.
4. Please do not put wireless charger close to cards with magnetic stripes or
chips (ID card,credit card etc.) to avoid demagnetization
5. Please keep wireless charger at least 20 CM distance away from implantable
medical device (heart pacemaker, Implantable cochlea etc.) to avoid potential
interferences.
6. Please do safekeeping, do not let your kids treat wireless charger as toy
to avoid unwanted accidents.
The pictures only supplies the reference, please take the actual product as
the standard.
FCC Statement:
FCC ID: 2APCQ-TAC-134 FCC WARNING:This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
FCC Statement:
— Reorient or relocate the receiving antenna. — Increase the separation
between the equipment and
receiver. — Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. — Consult the dealer or an
experienced radio/TV technician
for help.
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. During the operation of device a distance of 15 cm
surrounding the device and 20 cm above the top surface of the device must be
respected.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>