newone N3002 Wi-Fi Smart Plug Dimmer User Manual
- June 6, 2024
- newone
Table of Contents
newone N3002 Wi-Fi Smart Plug Dimmer
N3002
Introduction
The Minoston N3002 is a 300W MAX Loading smart dimmer plug designed for use seasonal and landscape lighting, porch light, and other indoor and outdoor plug-in small appliances. It’s compatible with dimmable LED, halogen, incandescent, and fluorescent bulbs. Works with Amazon Alexa, Google Assistant. You can use the free App–Smart Life, or voice control by Alexa and Google Assistant to operate your devices in your home.
Specifications
Power: 120VAC, 60Hz
Loading : 300W
Wireless Frequency: 2.4GHz Wireless Standard: IEEE802.11b/g/n
Program button:
Press 1x: On/Off
Press 3x: WiFi network configuration.
Hold the button: Ajust brightness
RGB LED indicator:
Sky-blue: Network configuration mode
Blue: Light status indicator
Red: Network Failure/Overloading Warning
Purple: AP Network configuration mode
APP Connection
Note:
Your device needs to be installed in the network coverage of your home router.
-
Please scan the QR code to download the application “Minoston”.
-
If you cannot download Smart Life app, please search “Minoston” on Google Play (for Android phone) or Apple Store (for iOS phone) to download.
After you download the Minoston App and register a new account, please follow the instructions below to set up your smart switch. -
The smart switch can be also used with Amazon Echo and Google Home. Please scan the QR code below and follow the instructions if you have any trouble pairing with them.
Note:
- Our products supports Bluetooth quick-fit and 2.4GHz Wi-Fi network.
- 3 connection network modes: Bluetooth quick-fit Mode, Easy Mode, AP Mode. Choose the most suitable mode to configure the network.
- Please operate quickly when the sky-blue LED indicator blinks rapidly.
- When indicator flash enters the network, complete standard operation within the 3 minutes.
- If you failed to connect with Wi-Fi network, please try to operate several times more.
Overloading protection is protection against overheating of the protected equipment. When the device’s temperature is high, the LED will light up in red and cut down the power. Please power off the device and use it after the temperature of the device drops.
When the LED is purple (AP mode), please press the button 3 times quickly until the LED change to Sky-blue and LED blinks–Back to EASY MODE.
NOTE: Do not plug an extension cord in this smart plug.
Bluetooth quick-fit Mode
-
Plug-in the device directly to the wall outlet. Once pluged in, it will enter into the Buletooth auto-connection mode.
White LED indicator
The auto-connection comes with led blinks. The LED will blinks 3 minutes. If it stopped, please hold the button 5 seconds until the LED blinks again. -
Turn on your Phone bluetooth.
-
Tap ‘+’ to add this plug in the “Minoston”.
-
You’ll see “Devices to be added”—“Go to add”.
-
Click to “Add ”
-
Enter the Wi-Fi Password (Your phone should have connected to the same Wi-Fi first).
-
Wait for the app to connect to your Wi-Fi until it’s 100%. 8: Click and edit the name of
When the Bluetooth is off, APP will remind: “You are advised to enable Bluetooth”.
Easy Mode
FCC warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
this device may not cause harmful interference, and this device must acceptany
interference received, including interfer ence that may cause undesired
operation.
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment gener ates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interfer ence will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION – PLEASE READ!
This device (N3002) is intended for installation in accordance with the
National Electric Code and local regulations in the United States, or the
Canadian Electrical Code and local regulations Canadian Electrical Code and
local regulations in in Canada.Canada. If you are
MEDICAL EQUIPMENT
Please DO NOT use this plug to control Medical or Life Support equipment. This
device should never be used to control the On/Off status of Medical or Life
Support equipment
OTHER WARNINGS
Risk of Fire
Risk of Electrical Shock
Risk of Burns
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>