ORBEA Rise Hydro 2022 Bike User Guide

ORBEA Rise Hydro 2022 Bike

TURNING RISE ON/OFF

TO TURN RISE H ON

Press the power button on the lower part of the frame once.

TO SWITCH RISE H OFF

Press and hold for 3 seconds the power button on the lower part of the frame until the button’s light fades off.

CHANGE BETWEEN ASSIST MODES

Press the buttons X or Y of the Shimano handlebar remote switch to change between assist modes. Press X to increa-se the assist mode up to the maximum available (Boost).
Press Y to decrease the assist mode down to the No-Assist mode (Off).

CURRENT ASSIST MODE DISPLAY

When changing the assist mode, the current mode will be visible on the Shimano EW-EN100 junction (assemblies without display), on the Shimano display and/or your compatible Garmin unit with the Orbea RS Toolbox data field installed and connected to Rise.
Read the Orbea RS Toolbox section of this guide and the Rise Hydro Bluepaper to download, unlock and install Or-bea RS Toolbox on your compatible Garmin device.

WALK ASISST

To activate Walk Assist, press the handlebar remote lever switch button Y for 1 second until the word WALK appears on the Shimano display or the LED2 of the EN100 junction shows a dark blue light.
Release the Y button and press it again to engage Walk Assist. The system will help you push the bike along as long as the Y button is pressed.

CHARGING THE INTERNAL BATTERY

Before using the internal battery or the Range Extender for the first time, completely charge the batteries. Charge the internal battery and/or the Range Extender as soon as you receive it. If you are not going to use the bike or the Range Extender, make sure the batteries are charged to at least 50% of their capacity every 3 months.

1. Plug the RS Smart Charger to the mains outlet. With the charger not being connected to the bicycle, the LED on the charger’s body will blink in blue.
   

2. Open the bicycle charging port cover and connect the charger aligning the connector correctly. The arrow on the charger connector must be aligned with the top part of the charging port.
   The charger’s body LED will turn blue for 2 seconds and then it will start fading in and out cyclically until the battery is completely charged.
   

3. When the battery is fully charged, the charger’s body LED will light in blue permanently.
   

4. Disconnect the charger from the bicycle’s charging port carefully pulling from the charger’s connector. Make sure the charging port’s cover is correctly closed.
   While the charger is connected to Rise, the bicycle can-not be powered on. Disconnect the charger from the bike and turn the bike on to check the current battery level if you could not charge the battery completely.
   

NOTICE: If the charger´s LED lights in red when connecting the charger to the outlet or during the charging process, there is a charging anomaly. Immediately disconnect the charger and read the charger troubleshooting method in the Rise H Bluepaper technical manual. If the problem persists, contact an authorized dealer.

CHECKING THE BATTERY LEVEL

WITH SHIMANO DISPLAYS

Turn the bicycle on. On assemblies with the Shimano displays, the battery(ies) charge level will be shown on the screen.

COMPATIBLE GARMIN UNITS. ORBEA RS TOOLBOX

Turn you compatible Garmin unit (having previously down-loaded and installed Orbea RS Toolbox on it) and navigate to the RS Toolbox field.
Then turn the bicycle on to see the current battery level.
If the battery level is not displayed on Toolbox, switch the bicycle off and on again to reset the connection.
Read how to download and install the Orbea RS Toolbox data field on your compatible Garmin unit in the dedicated section of this manual.

WITH SHIMANO EW-EN100 JUNTION

Turn the bicycle on. The Shimano EW-EN100 junction will show in the LED1 the remaining battery charge of the battery(ies). The LED1 will display a green light until the battery charge is below 21%, after which the LED1 will show a red light. When the battery is almost depleted, the LED1 will blink in red.

SHIMANO ETUBE PROJECT APP. CUSTOMIZE YOUR RISE

Using the Shimano Etube Project Cyclist app for smart-phones, you can customize the EP8 RS system to adjust Rise to your needs. Every assist mode can be modified to deliver the exact power for your riding style.
Download the Shimano Etube Project Cyclist app from Apple Store or Google Play.

The EP8 motor also allows the selection of two different assist profiles. Within each profile, the power output of each assist mode can be modified to achieve the power that you need in every situation.
The assist profile 1 is designed for activities with less steep climbing, slightly reducing the power delivery for a greater available range.
The assist profile 2 is designed for more demanding activities and steeper climbs, delivering more power from the motor.
Consult the complete Etube Project app manual on Shimano’s website. Etube Project also lets you customize the remote levers buttons, view error reports, update the components firmware, amongst other functions.
Read the complete app manual here:
https://si.shimano.com/#/en/iUM/7J4MA
You can also read on how to change the assist profiles and modify the assist modes on the Rise Hydro Blue Paper technical manual.

SWITCHING BETWEEN ASSIST PROFILES

On Rise models without a Shimano display, you will need to connect your bicycle to the Etube Project app to select your current assist profile.
On models equipped with a Shimano display, you can select the assist profile through the display, although to customize the assist modes you will need to connect your bicycle to the Etube Project app.

SYSTEM WARNINGS AND ERRORS

When an error or warning is detected in the system, both LEDs on the Shimano EW-EN100 junction will blink in red. In assemblies with a Shimano display, the error code will be shown on the screen.

You can connect your bicycle to the Etube Project app to know the error or warning code and its troubleshooting procedure. Turn the bicycle Off and On again and connect it to the app.
The error code and the troubleshooting procedure will be shown in the section Maintenance>Error Log.

ORBEA RS TOOLBOX. DATA FIELD FOR GARMIN COMPATIBLE UNITS

NOTICE: Consult the complete Orbea RS Toolbox data field manual on the Rise Hydro Blue Paper technical manual from Orbea’s website.

Watch the video on how to install and configure Orbea RS Toolbox on Garmin devices:
www.youtube.com/watch?v=F-4lUxxOuFs
Or scan the QR code below to access the video directly:

INSTALL AND UNLOCK ORBEA RS TOOLBOX ON GARMIN DEVICES. GARMIN CONNECT

APP

Orbea RS Toolbox is an app for Garmin compatible devices exclusive for Rise owners. It is added to your Garmin device as a data field and allows you to access relevant information of your Rise while riding.

NOTICE: The following method describes how to install and unlock Orbea RS Toolbox on your Garmin device using the smartphone app Garmin Connect through a Bluetooth connection. You can use the same procedure on your PC or Mac using Garmin Ex-press, connecting your device to your computer using an USB cable.

NOTICE: To unlock Orbea RS Toolbox on your Garmin device, you must have registered your new Rise’s barcode on Orbea’s website, which also lets you enjoy the Life Warranty on your new frame. Go to Orbea’s website and register your bike’s barcode, creating an account first if you do not have one yet.
www.orbea.com/es-es/access-register

Your bicycle’s barcode is an 11-digit code you will find on the bicycle’s frame:

1. After you have registered your Rise on Orbea’s website, open the Garmin Connect app on your smartphone and connect your device via Bluetooth.

You can download and install Garmin Connect from Google Play or Apple Store.

2. Select “Activities and App Management”.

3. Select “Data Fields”.

4. Select “Get More Data Fields”.

5. Search “Orbea RS Toolbox” in the Garmin IQ Store. Select Unlock Orbea RS Toolbox.
   NOTICE: If you cannot see the app Orbea RS Toolbox in the IQ Store, your device is not compatible with the app. We are working to include new devices every day, contact Orbea if you need more information.
   NOTICE: In some watch models and series 30 Edge units, the ecosystem of the IQ Store that you will be sent to from Connect in order to search for RS Toolbox will only show the Install button.
   In this case, download RS Toolbox and go back to Connect and synchronize your device. Then select Data Fields > Orbea RS Toolbox and choose “See in Store” The screen you will be taken to will now show the Unlock button.
   Follow the unlock process from step 5 of this section. If once you have finished it is not possible to visualize.
   Toolbox on your device, uninstall Toolbox from Garmin Connect and start again the installation process, selecting “See in Store” once you have installed Toolbox (this could happen because the unlocking process for the first download did not work).
   
   
   
   
   

6. A message will inform you that you are about to leave the IQ Store. Accept to be redirected to Orbea’s activation website.
   

7. Input your login details to your Orbea account.
   

8. If you had already registered your Rise barcode, a message will inform you that your Garmin device has been unlocked.

9. Go back to Garmin Connect on your phone. You will notice that the Unlock button is still visible on the Orbea RS Toolbox screen. Type again Orbea RS Toolbox on the search field of Garmin Connect and select Toolbox. Now the Unlock button will have disappeared and only the Download button will be visible. Download Orbea RS Toolbox. A message will inform you that the app will be installed the next time you synchronize your device.

10. Go to Garmin Connect on your smartphone and synchronize your Garmin device with the app.

11. Go to “Activities and App Management > Data Fields”. You will see Orbea Toolbox installed on your device. If Toolbox is visible but it is not installed, synchronize your device.

ENABLING ORBEA RS TOOLBOX IN YOUR DEVICE*

After downloading and unlocking Toolbox through Garmin Express (PC or Mac) or Garmin Connect (smartphones) and synchronizing your Garmin unit, activate the visualization of the data fields in your device.
Below is shown the method to see the Toolbox data field on both Garmin Edge and watches compatible units.

1. Turn on your bicycle and the unit you have installed Orbea RS Toolbox on, they will pair automatically.

2. Access Activity Profiles from the Setting menu in your device and choose the profile you want to use your bicycle with.
   

3. Select “Data Fields” and the page of the activity profile on which you want to see the data from your bicycle. Enable the data page and choose to see one data field on the page.

4. Scroll through the data to be seen on the screen. Select Connect IQ and choose Orbea RS Toolbox.
   If you had not turned on your bicycle before setting up Toolbox on your device, the unit will show the message “Searching…” after selecting the Orbea RS Toolbox data field. When you turn on your bicycle and access the page where you chose to see Toolbox, the data from your bicycle will be visible.
   

5. With the bicycle turned on, access the activity profile on which you selected to see the data from Toolbox or start recording an activity on this profile with your Garmin unit. Navigate to the page you selected to see Toolbox on to access the real-time data from your bicycle.
   

• Read more about Orbea RS Toolbox data field manual on the Rise Hydro Blue Paper technical manual from Orbea’s website.

EXTERNAL BATTERY RS RANGE EXTENDER

NOTICE: If Rise was On when connecting the Range Extender to the bicycle, the system will turn itself Off and you will need to turn Rise On again by pressing the power button.

This happens so the system can reboot and recognize the Range Extender as part of the power system when Rise is turned On again.
If you were recording an activity with Garmin Connect using Orbea RS Toolbox, this will have no effect on the data recorded in the activity. The Rise data will keep registering when you start using Rise again.
Once you turn Rise on, the Range Extender will be operative. It is not necessary to turn the Range Extender On.
If the Range Extender is disconnected when the bicycle is On, the bicycle will turn itself Off and it will be necessary to turn the bicycle back on. This happens so the system can reboot and recognize the internal battery as the only current power supply.

RANGE EXTENDER ASSEMBLY

1. Install the Range Extender dedicated mount onto the downtube and fix it in place with the original bolts with a recommended torque setting of 5 Nm.
   

2. When installing the Range Extender holder, remove the four washers pre-installed on the frame and make sure that, once installed, the Range Extender´s six contact points rest correctly against the downtube.
   

3. Install the Range Extender into the mount and secure it with the side o-ring.
   
   The Range Extender bottle holder is compatible with standard bottles when the Range Extender is not installed.

CONNECTING THE RANGE EXTENDER TO RISE HYDRO

1. Turn the safety tabs of the Range Extender cable counter-clockwise before connecting it to the battery.
2. Connect the cable to the Range Extender charging port. Open the bicycle charging port and connect the Range Extender cable.
3. Turn the cable’s safety tabs clockwise to lock the cable in place.
   To disconnect the Range Extender cable or to remove the Range Extender from the bicycle to charge it, turn first the cable’s safety tabs and carefully pull from the cable’s connector.

NOTICE: If Rise was On when connecting the Range Extender to the bicycle, the system will turn itself Off and you will need to turn Rise On again by pressing the power button. This hap-pens so the system can reboot and recognize the Range Extender as part of the power system when Rise is turned On again.
If you were recording an activity with Garmin Connect using Orbea RS Toolbox, this will have no effect on the data recorded in the activity. The Rise data will keep registering when you start using Rise again. Once you turn Rise on, the Range Extender will be operative. It is not necessary to turn the Range Extender On.
If the Range Extender is disconnected when the bicycle is On, the bicycle will turn itself Off and it will be necessary to turn the bicycle back on. This happens so the system can reboot and recognize the internal battery as the only current power supply.

OPERATION OF THE RANGE EXTENDER

The Range Extender powers the EP8 RS motor directly. When using Rise with a Range Extender connected to the system, the motor will only draw power from the Range Extender until the Range Extender is depleted. When there is no charge left in the Range Extender, the internal battery will start powering the motor if it had any charge left.

BATTERY LEVEL VISUALIZATION

COMBINED BATTERY LEVEL
When a Range Extender is connected to Rise, the system calculates the total capacity of both the Range Extend-er and the internal battery (792 Wh) and the remaining battery level information for the system will take into ac-count the charge left on both batteries out of the total 792 Wh capacity.
The combined charge level will be visible trough the Shimano junction or display or the Orbea RS Toolbox data field for compatible Garmin devices.

STANDALONE RANGE EXTENDER BATTERY LEVEL
Press once the Range Extender main button to know the current charge level.
The LEDs will show the current charge level in 25% increments from right to left for 5 seconds.
When the Range Extender is connected to the bicycle and its charge is depleted, the system will show, by means of the available methods (displays, junction or RS Toolbox) the available charge in the internal battery only, accounting for the capacity of the internal battery alone and not the internal battery and the Range Extender system total capacity.

CHARGING THE RANGE EXTENDER

1. To charge the Range Extender, plug the RS charger to the mains outlet. With the Range Extender not being connected to the charger, the LED on the charger’s body will blink in blue.
   

2. Disconnect the Range Extender connection cable to the bicycle charging port (in case it is connected) by turning counterclockwise the cable safety tabs first and carefully pulling from the cable.
   

3. Connect the charger to the Range Extender correctly aligning the connector pins with those of the Range Ex-tender’s charging port. The charger’s body LED will turn blue for 2 seconds and then it will start fading in and out cyclically until the battery is completely charged.
   
   While the Range Extender is being charged, the charge indicator LEDs will show the current battery level. The blinking LED shows the range (in 25% increments) that is currently being charged.

4. When the battery is fully charged, the charger’s body LED will light in blue permanently. Disconnect the charger from the charging port by carefully pulling from the charger connector.
   

NOTICE: If the charger’s LED lights in red when connecting the charger to the outlet or during the charging process, there is a charging anomaly. Immediately disconnect the charger and read the charger troubleshooting method in the Rise H Bluepaper technical manual. If the problem persists, contact an authorized dealer.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>