FRESKO V3 Automatic Vacuum Sealer User Guide

FRESKO V3 Automatic Vacuum Sealer

Introduction

Congratulations on the purchase of this modern and high-quality product. This instruction manual contains important information on safety, usage and disposal. Before using the product, familiarize yourself with all handling and safety guidelines. This device may only be used as described and for the purposes indicated. Please also pass these operating instructions on to any future owner(s).

Safety Instructions

Always abide by the following safety rules and instructions when using electrical appliances and read these instructions carefully before using the vacuum sealer. Read all instructions.

WARNING : Do not immerse the vacuum sealer in water or other liquids when cleaning it. If the supplied power cord is damaged, it should be replaced by a
qualified technician in order to avoid a hazard.

• short detachable power-supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord.
• Extension cords [or longer detachable power-supply cords) are available and are not prohibited from being used when care is exercised in their use.
• When an extension cord is used:

1. The marked electrical rating of the detachable power-supply cord or extension cord shall be no less than the marked electrical rating of the product;
2. The longer cord shall be arranged so that it does not drape over the counter-top or tabletop where it is capable of being tripped over, snagged, or pulled on unintentionally, especially by children.

CAUTION:
Household use only.

Do not immerse in water. To reduce the risk of electric shock, this product has a polarized plug Cone blade is wider than the other). This plug is intended to fit in a polarized outlet only one way. When the plug does not fit fully in the outlet, reverse the plug. When it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plugin any way. Close supervision is required when this product is used near children.
Save These Instructions.

Operating Instructions

• If the SUPPLY CORD is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.
• A short power-supply cord is to be provided to reduce the risk resulting from becoming entangled in or tripping over a longer cord.
• Longer extension cords are available and may be used if care is exercised in their use.
• If an extension cord is used,

1. The marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance;
2. The longer cable should be arranged so that it does not hang over the countertop or tabletop where it can be pulled by children or where it can be accidentally tripped over.

Placement

• Always place the vacuum sealer away from the edge of the countertop.
• Make sure the vacuum sealer is placed on a firm, flat surface.
• Do not use the vacuum sealer outdoors or near water.

WARNING : When using the machine, please do not place the vacuum sealer on a metal tray or metal surface.
Personal Safety

WARNING : To protect against fire, electric shock and personal injury, do not immerse the plug and vacuum sealer in water or any other liquid.
To reduce the risk of electric shock, this product has a polarized plug [one blade is wider than the other). This plug is intended to fit in a polarized outlet only one way. When the plug does not fit fully in the outlet, reverse the plug. When it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Other Safety Considerations

• Only use officially-provided attachments and accessories.
• Do not use the vacuum sealer for any use other than its intended purpose.
• Keep the vacuum sealer away from heat sources.
• When using the vacuum sealer, make sure the lid is properly in place and secure before the operation.

CAUTION : To prevent damage to the vacuum sealer, do not use water or any liquid when cleaning.

Disposal of Packaging Materials

• The packaging protects the appliance from damage during carriage.
• The packaging materials have been selected for their environmental friendliness and ease of disposal, and are therefore recyclable.
• Returning the packaging to the materials cycle conserves raw materials and reduces the amount of waste that is generated. Dispose of packaging materials that are no longer needed in accordance with applicable local regulations.

Note: If possible, keep the original packaging during the warranty period so that the device can be properly packed for return in the event of a warranty claim.

Scope of Delivery
The appliance is supplied with the following components as standard:

• 1 x Vacuum Sealer
• 2 x Vacuum Tubes
• 1 x Power Cord
• 20 x Vacuum Bags (8×12 Inches)

Check the package for completeness and for signs of visible damage. If the consignment is incomplete or damaged due to defective packaging or carriage, please contact us.

Installation Requirements
For safe and trouble-free operation of the device, the set-up location must fulfill the following requirements:

• When setting it up, place the appliance on a firm, flat and horizontal surface.
• Do not place the device in a hot, wet or extremely damp environment or in the vicinity of flammable materials.
• The mains power socket must be easily accessible, so that the power cable can be easily disconnected in the event of an emergency.

Electrical Connection

• Before connecting the device, compare the connection data (voltage and frequency) on the type plate with those of your power supply. This data must match to prevent damage to the device.
• Make sure that the power cord is undamaged and does not run over hot surfaces and/or sharp edges.
• Make sure that the power cord is not taut or bent.
• Do not let the power cable hang over edges (trip wire effect).
•  Insert the plug into the mains power socket.

Equipment Operation Instruction

Note : After the machine finishes the single sealing, it needs rest time. (For the first time, the cooling process will be delayed for about 5 seconds, which means that it is improper to operate the machine in 5s, as the temperature of the machine is still very high and the rest time may be correspondingly longer to protect the machine). During the rest time, there is no response no matter pressing any buttons.

Automatic Standby
The machine will go to standby mode automatically if there is no operation after 10 minutes. In standby mode, only the “Seal” light is on, the other lights are off, please press “Seal” button to reawake.

DRY

1. Place the vacuum sealer on a flat surface and plug in the power. After filling the food to the vacuum bag, put the vacuum bag flatly into the vacuum sealer. Please leave at least 80mm (3.15 inches) from the edge of the food to the opening of the bag so as to keep enough space for vacuuming and sealing.
2. Select the “DRY” button according to the food (Pic.2). Press the button and it will vacuum and seal automatically. At first, the “DRY” begins to flash in white light. Then the flashing “DRY” light stops and “SEAL” begins to flash. After the light of Circle Progress Bar comes in full, the machine finishes vacuuming and sealing.
3. “DRY” and “SEAL:’ restore the white light to stay on. After sealing, it will automatically deflate and reset, and you could take out the sealing bag (Pic.3).
   NOTE : To stop working, just press “DRY”button, the machine will automatically stop vacuuming or sealing.

MOIST

1. Place the vacuum sealer on a flat surface and plug in the power. After filling the food to the vacuum bag, put the vacuum bag flatly into the vacuum sealer. Please leave at least 100mm (3.93 inches) from the edge of the food to the opening of the bag so as to keep enough space for vacuuming and sealing.
2. Select the “MOIST” button according to the food [Pic.2). Press the button and it will vacuum and seal automatically. At first, the .MOIST” begins to flash in white light. Then the flashing .MOIST” light stops and “SEAL” begins to flash. After the light of Circle Progress Bar come in full, the machine finishes vacuuming and sealing.
3. MOIST” and “SEAL” restore the white light to stay on. After sealing, it will automatically deflate and reset, and you could take out the sealing bag [Pic.3).
   NOTE : To stop working, just press “MOIST”button, the machine will automatically stop vacuuming or sealing.

SEAL

1. Place the vacuum sealer on a flat surface and plug in the power. After filling the food to the vacuum bag, put the vacuum bag flatly into the vacuum sealer.
2. If you only need to seal the food but no need to evacuate air in the bag, just press the “SEAL” button [Pic.2), then the sealing white indicator flashes.
3. The light stops flashing and stays on, which means that the machine has finished sealing. It is feasible to remove the bag at this time.
   NOTE : To stop working, just press “SEAL” button, the machine will automatically stop vacuuming or sealing.

EXTERNAL VACUUM

1. Connect the external pumping component to the external evacuation hole, then connect the other end of the external pumping component to the vacuum tank.

2. Press the external pumping control button • “EXTERNAL VACUUM” is on. When the vacuum sealer starts to work, the
   “EXTERNAL VACUUM” button will flash in white light.

3. The vacuum sealer stops pumping, “EXTERNAL VACUUM” stops flashing and stays on.
   Note : When the external pumping function is no longer used, please remove the external pumping component, press the external pumping control button, and the white light of “External Vacuum” will be continuously switched to “SEAL” white light.
   NOTE : To stop working, just press the external pumping control button, the machine will automatically stop vacuuming or sealing.

VACUUMING RED WINE

1. Connect the wine cork to the external evacuation hole, then connect the wine cork into the wine bottle.
2. Press the external pumping control button, the “EXTERNAL VACUUM” is on. When the vacuum sealer starts to work. the “EXTERNAL VACUUM” button flashes in white light.
3. The vacuum sealer stops pumping, “EXTERNAL VACUUM” stops flashing and stays on.
   NOTE : After the machine finishes the single sealing, it needs rest time. [For the first time, the cooling process will be delayed for about 5 seconds, which means that it is improper to operate the machine in 5s, as the temperature of the machine is still very high and the rest time may be correspondingly longer to protect the machine). During the rest time, there is no response no matter pressing any buttons.

Freshness comparison table

Documents / Resources

| FRESKO V3 Automatic Vacuum Sealer [pdf] User Guide
V3, Automatic Vacuum Sealer
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>