SprintRay ProCure 2 High-Speed Post Curing System Designed for Digital Dentistry User Guide

June 6, 2024
SprintRay

SprintRay ProCure 2 High-Speed Post Curing System Designed for Digital

Dentistry User Guide

Congratulations!

In this brief guide, you’ll learn how to set up and use your ProCure 2 post- curing system.
Your purchase comes with a complimentary, live 30-minute.
Q&A with one of our expert technicians. For advanced users, visit our website for tips & tricks.
We’re so excited to see what you make!

1. In the Box

ProCure 2                                Curing Tray Refer to section 5

Power Cord            USB Cable  With USB type C adapter         Onboarding Card

2. Where to Set Up

Situate Pro Cure 2 in a well-ventilated area on a flat, level surface. Keep it away from extreme temperatures, windows, and direct sunlight.

Recommended
Operating Temperature

Level Surface

Uneven Surface
Warm Environment

3. Plug in ProCure 2

Use the provided power cable to plug ProCure 2 into a surge protector or unit erupted power supply. Turn it on by flipping the power switch located on the back of the unit.
To perform a reset, use the power switch or disconnect Pro Cure  2 from its power source.

4. Connect to a Wireless Network

Press the wireless connection icon using the touchscreen and follow the steps to connect to your network. Firewall or antivirus software may prevent
ProCure 2 from establishing a reliable connection. Consult SprintRay customer support if you need help connecting to a network.

Install Curing Tray

Place Tray Inside Curing Drawer

Open the UV drawer by pulling on the handle. Set the Curing
Tray in the drawer so that it rests inside the frame. Close the drawer slowly to ensure the tray is properly in place.

Height Limit is 3” (75mm)

Models inserted into ProCure 2 cannot exceed 3” (75mm) in height. Refer to the height limit indicator on the Curing Tray to ensure optimal performance.

6. Using ProCure 2

How to Operate

Pull on the handle to open the curing drawer. Place models on the curing tray and close the drawer. Select desired material from the touchscreen to begin the process.

Understanding Zone Selection

ProCure 2 can selectively cure the model tray to reduce time when fewer models are being processed. You can select which zones to cure from the touchscreen.

WARNING

ProCure 2 may become warm to the touch during post-curing.
Do not obstruct the ventilation located on the rear and bottom of the unit.

7. Maintenance

Software Updates

ProCure 2 will periodically receive updates over the air via wireless network.
Ensure ProCure 2 is connected to the internet to receive updates

Troubleshooting

Please call customer support to perform advanced troubleshooting. A USB cable with a type C adapter is provided to connect ProCure 2 to your computer if needed.

Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Training and Support

Sign up for your free Q&A and contact our
team of support technicians with questions.

Visit support.sprintray.com
Call  800-914-8004
Email  support@sprintray.com

FCC Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

Please make sure that the product is normally connected to the wifi network during use, and the contact voltage is good during use. In order to have a good experience of using the product, please keep at least 20 cm when working.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals