OUTDOOR ROUTER EZR33 Series EZR33L-A4 Outdoor 4G Wi-Fi Router User Guide
- June 6, 2024
- OUTDOOR ROUTER
Table of Contents
EZR33 SERIES QUICK GUIDANCE
https://ezr33.outdoorrouter.com/v/33l
EZR33.OutdoorRouter.com/v/33l
Scan QR code or visit URL link to see the complete edition of the online
manual.
PACKAGE CONTENTS
STEP 1.1 Check and count the package contents.
| Outdoor Router
---|---
| 4G & Wi-Fi Antennas
| 10-Meter LAN Cable
| PoE Injector PLUG
for UK / EU / US / AU
| L-Bracket & T-Wrench
| Mounting Kit
INTERFACE OVERVIEW
MOTHERBOARD | SIM CARD & PoE
STEP 2.1
SIM CARD
TURN OFF POWER BEFORE INSERTING THE SIM CARD
- Use the pin to push the pinhole until the SIM card tray pops out
- Insert a SIM card in the SIM1 slot
- Reposition the SIM card tray in the slot and push it back
WARNINGS
Use activated SIM card in the router
Make sure the SIM card is working well
Insert SIM card in the SIM1 slot
STEP 2.2
Make sure the mobile carrier has a strong enough signal in your area The modem
sensitivity is -101dBm equals to approx. 2-bar on a phone Refer to
https://ezen.link/signal-test
STEP 2.3
- Take the cap off from the gland. Push out the stopper from the inside of the gland.
- Take one end of the LAN cable through the cap.
- Put LAN cable through the barrel screw and plug in the PoE & LAN port on the motherboard.
- Clamp the stopper on the LAN cable and settle it in the barrel. * The smaller end faces the outside.
- Turn the cap in the clockwise direction to tighten it on the barrel screw.
- Connect another end of the LAN cable to the PoE port on the PoE injector.
- Connect AC plug on the PoE injector to an electrical outlet until set up all the below steps (to 3.3).
NOTE
To exchange the AC plug, press and hold the Push button then push the AC plug
upward to take it off.
8. ETHERNET
Connect a computer to the LAN port on the PoE injector to get the Ethernet
connection. To use another router, connect its WAN port to the LAN port on the
PoE injector.
STEP 2.4
Close the lid & press it with your hand.
Use T-wrench to tighten four pieces
hexagon bolts on the lid.
Ensure no gap after tightening the screws!
STEP 2.5
ANTENNAS
Locate embossed numbers
1~6 on the top & bottom sides 1 & 3 for 4G antennas
4 & 6 for Wi-Fi antennas
Turn the hex part on the antennas in the clockwise direction to tighten them
BRACKET & MOUNTING
STEP 3.1
Walk around with a mobile phone and check the network type and signal bars.
Then choose a location with a 4G LTE network reception and strong signal
reception.
STEP 3.2
Use the cross end on T-wrench and M6 cross-head screws to install the L-shape
bracket on the backside of the enclosure.
** Turn the bracket to be parallel with the pole if it’s horizontal.
STEP 3.3
INSTALL ON A POLE
Find a pole with a diameter of Ø35~50mm.
1. Clasp the pole with U-bolts and holders, attach them on either side of the
L-shape bracket.
2. On another side of the bracket, put washers, spring washers, and hex nuts
on U-bolts. Tighten the nuts with an M10 spanner.
After turning on power (step 2.3.7), use a phone or computer to join the Wi-Fi
hotspot Outdoor-WiFi-xxx or connect the computer to the LAN port on the PoE
injector (step 2.3.8).
Open a web browser, enter the router IP http://192.168.30.1 on the address
bar.
Click the Login button to access the admin panel.
If unable to access, recheck the Wi-Fi and LAN connections and clean the web
browser cache.
STEP 4.2
After accessing the router admin panel, navigate to System > System from
the top menu.
Under the tab of General Settings, click the Sync with browser button to sync
the time.
Router password
Go to System > Administration, input new custom router password twice,
and save settings.
*Keep the new password in a safe place.
STEP 4.3
Go to Network > Wireless, click the Edit button on SSID: Outdoor-WiFi-xxx
(Mode: Master).
Scroll down to Interface Configuration, change Wi-Fi SSID on ESSID field.
Wi-Fi SSID & password
Click the tab of Wireless Security, choose WPA-PSK/WPA2-PSK on Encryption.
Input the Wi-Fi password on the Key field, then save settings.
It will use 1-2 minutes to reboot the Wi-Fi hotspot.
STEP 4.4
MOBILE MODEM
1. Status| On the front page, check the modem status and the signal strength
on the
right-side DEVICE section.
---|---
2. Interface| Go to Network > Interfaces, check the IP, and traffic flow of the
MOBILE interface.
3. APN| t is non-necessary to change APN unless the mobile carrier requires
to do so.
Click the Edit button on the MOBILE. Tap the Primary SIM1 (or SIM2) tab to
change APN.
- Check the APN tutorial on https://ezen.link/APN.
4. Protocol| It is also not necessary to change the protocol unless the default one is not supported. - Check the protocol tutorial on https://ezen.link/protocol.
5. Debug| Status
Disabled Connection attempt failed Network device is not present Connected but no internet
Solution
Check if the SIM card is locked.
Re-insert the SIM card and check the signal strength.
The Guardian module is resetting. Wait for 2-3 minutes.
Check if the data plan supports use on a 4G router.
LOCAL NETWORKS
Turn on DHCP mode on the phone or computer to obtain a local IP address from
the
4G router. To use a static IP address, please comply with the below format.
Computer IP
Subnet mask
Gateway (Router IP)| 192.168.30.100~249 ( pick one IP from 100~249 )
255.255.255.0 ( 24 on Windows )
192.168.30.1
---|---
STEP 4.6
RECOVERY
Reboot| The router might have glitches after running for days or weeks.
Rebooting the router could solve most of the issues.
You may go to System > Reboot or unplug the PoE injector to reboot the router.
---|---
Soft Reset| If the router works unstable after making changes to the firmware,
please go to
System > Backup / Flash Firmware. Click the Perform reset button to run a soft
reset.
Hard Reset| If unable to access the router admin panel, please run a hard
reset.
When the device is powered on, tap and hold the round Reset button for 5
seconds.
Then release it and wait for 4 minutes to boot up.
! IMPORTANT! DO NOT TURN OFF POWER WHILE RESETTING THE ROUTER!
Thanks for reading! If you have questions while using the router, please check
the online manual at
ezr33.outdoorrouter.com/v/33l
Please feel free to contact us if you need any further assistance.
WORKING PRINCIPLE
WIE FUNKTIONIERT EIN 4G-ROUTER?
FCC Statement
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
This device does not cause harmful interference.
This device must accept any interference received, including interference that
may cause undesired operation.
If this device is modified without authorization from Ezen, the device may no
longer comply with FCC requirements for Class B digital devices. In that,
case, your right to use the device may be limited by FCC regulations.
Moreover, you may be required to correct any interference to radio or
television communications at your own expense.
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This device generates, uses and radiates
radiofrequency energy. If it is not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this device does cause harmful interference to
radio or television reception, which can be determined by turning the device
off and on, the user may take one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Reinforce the separation between the device and receiver.
- Connect the device into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio or TV technician for assistance.
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This equipment should be
installed and operated with a minimum distance of 20 centimeters between the
radiator and your body. The device contains LTE Module: EC25-AF (Contains FCC
ID: XMR201808EC25AF).
OutdoorRouter
www.outdoorrouter.com
Feel free to contact us if you need any further assistance.
Call Us
United Kingdom +44 020 3575 1156
United States +1 323 521 4621
Australia +61 02 8205 3116
Send An E-Mail
sales@outdoorrouter.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>