poly P078 Studio X30 Video Conferencing Kit Instruction Manual

poly P078 Studio X30 Video Conferencing Kit

Poly Studio X Family

This document covers the following Poly Studio X models:

• Poly Studio X30 (models P018 & P018NR)
• Poly Studio X50 (models P017 & P017NR)
• Poly Studio X70 (models P026 & P026NR)

Service Agreements
Please contact your Poly Authorized Reseller for information about service agreements applicable to your product.

Safety, Compliance, and Disposal Information

• This equipment is intended for indoor use only.
• This equipment is not intended to be directly connected to outdoor cables.
• Always disconnect the system from power and telecommunications networks before cleaning or servicing.
• In order to remove all power from this unit, disconnect the power supply mains cord.
• Do not spray liquids directly onto the system when cleaning. Always apply the liquid first to a static-free cloth.
• Do not immerse the system in any liquids or place any liquids on it.
• Do not disassemble this system. To reduce the risk of shock and to maintain the warranty on the system, a qualified technician must perform service or repair work.
• There are no user serviceable parts inside this product.
• Users must not service any parts in compartments that require a tool to access.
• This equipment should be used only on even surfaces.
• This product is intended to be powered by an external (LPS) power supply – use only the type which is supplied with this product.
• Do not use a power cord that is damaged. This could cause fire or electric shock. Contact the manufacturer for a replacement cord, if necessary.
• Only use a power cord which is appropriately rated and approved relevant to the country of use.
• This system is considered to be Pluggable Equipment Type A. The socket outlets must be installed near the equipment and be easily accessible.
• This equipment is not intended to be operated by children.
• When connecting to the mains supply, connect only to an earthed supply outlet.
• Keep ventilation openings free from any obstructions.
• The ambient operating temperature rating of this equipment is 0 – 40ºC and should not be exceeded.

Installation Instructions

Installation must be performed in accordance with all relevant national wiring rules.

Plug Acts as Disconnect Device
The socket outlet to which this apparatus is connected must be installed near the equipment and must always be readily accessible.

USA

Part 15 FCC Rules
This device is compliant with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interferences received, including interference that may cause undesired operation.

In accordance with part 15 of the FCC rules, the user is cautioned that any changes or modifications not expressly approved by Polycom Inc. could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Modifications
In accordance with Part 15 of the FCC Rules, the user is cautioned that any changes or modifications not expressly approved by Polycom, Inc. could void the user’s authority to operate the equipment.

Radiation Exposure Statement
The antenna used for this transmitter must be installed to provide a separation distance of at least 20 centimeters from all persons and must not be co located or operating in conjunction with any other
antenna or transmitter. This device with its antenna complies with FCC’s RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance, this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Canada

Industry Canada Statement
This device complies with RSS247 of the Industry Canada rules and also with ISED’s license-exempt RSS regulations. Operation is subject to the two following conditions:

1. This device does not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

This device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
This Class [A] digital apparatus complies with Canadian ICES-003.

Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20cm between the radiator & your body.

FCC and Industry Canada Example Label

See an example of the Poly Studio X30 (P018) regulatory label below. FCC ID: M72-P018
IC: 1849C-P018

See an example of the Poly Studio X50 (P017) regulatory label below.
FCC ID: M72-P017
IC: 1849C-P017

See an example of the Poly Studio X70 (P026) regulatory label below.
FCC ID : M72-P026
IC: 1849C-P026

EEA

CE Mark
P017, P018, and P026 are all marked with the CE mark. This mark indicates compliance with EU Radio Equipment Directive (RED) 2014/53/EU, RoHS Directive 2011/65/EU and Comission Regulation 278/2009.

P017NR, P018NR and P026NR are all marked with the CE mark. This indicates compliance with the EU EMC Directive (EMCD) 2014/30/EU, Low Voltage Directive (LVD) 2014/35/EU, RoHS Directive
2011/65/EU and Comission Regulation 278/2009.

A full copy of the Declaration of Conformity for each model can be obtained at www.poly.com/conformity

Poly Studio X Family Radio Operating Frequency

The frequency ranges in the following table apply to Poly Studio X30 (P017), Poly Studio X50 (P018), and Poly Studio X70 (P026).

Radio Operating Frequency

Maximum Transmit Power

Frequency Range| P017| P018| P026
2422 – 2480 MHz| Max EIRP [19.1]

dBm

| Max EIRP [18.88]

dBm

| Max EIRP [19.9] dBm
5150 – 5350 MHz| Max EIRP [19.93]

dBm

| Max EIRP [20.06]

dBm

| Max EIRP [19.9] dBm
5470 – 5725 MHz| Max EIRP [19.33]

dBm

| Max EIRP [19.7]

dBm

| Max EIRP [19.9] dBm

Japan

Models P017, P018, and P026 devices are only approved to transmit indoors within the W52 and W53 bands for Japan:

• W52(5180MHz / 5200MHz / 5220MHz / 5240MHz)
• W53(5260MHz / 5280MHz / 5300MHz / 5320MHz)

This product can’t be connected directly to the telecommunications circuits (or public wireless LANs) of any telecommunications carriers (e.g., mobile communications carriers, fixed communication carriers, or internet providers). To connect this product to the Internet, be sure to connect it via a router.

Taiwan

Taiwan RoHS table (P018)

Taiwan RoHS table (P017)

Operating Ambient Temperatures

• Operating temperature: +32 to 104°F (0 to 40°C)
• Relative humidity: 5% to 95%, noncondensing
• Storage temperature: -40 to +160°F (-40 to +70°C)

Waste Electrical and Electronic Equipment (WEEE)
All Poly products that fall within the scope of the EU WEEE Directive carry the crossed wheelie bin symbol which advises customers not to recycle electronic products in the domestic waste stream but to recycle them safely as e-waste.

Restriction of Hazardous Substances Directive (RoHS)
All Polycom products comply with the requirements of the EU RoHS Directive. Statements of compliance can be obtained by contacting typeapproval@poly.com

Environmental
For the latest environmental information including Networked Standby Efficiency, Battery use and disposal, take back RoHS and Reach, please visit https://www.poly.com/us/en/company/corporateresponsibility/environment

End of Life Products
Poly encourages you to recycle your end-of-life Poly products in an environmentally considerate way. We recognize our Extended Producer Responsibility (EPR), in accordance with the requirements of the European Waste Electronic and Electrical Equipment (WEEE) Directive 2012/19/EU.

All Poly products are marked with the crossed wheelie bin symbol shown below. Products that carry this symbol should be not be disposed of in the household or general waste stream. Further recycling information and detail of the options open to you, including our voluntary free global recycling service to ISO 14001 standard can be found at: https://www.poly.com/WEEE

The Poly Global Producer Responsibility Statement can be found in the Environment section of the Poly.com website.

Poly Take Back
In addition to any mandated take back requirement, Poly offers free recycling of its branded products to business users. Detailed information is available at www.poly.com/us/en/company/corporateresponsibility/environment

Getting Help and Copyright Information

GETTING HELP
For more information about installing, configuring, and administering Poly products or services, go to the Poly Online Support Center.

Plantronics, Inc. (Poly – formerly Plantronics and Polycom)
345 Encinal Street
Santa Cruz, California
95060

Polycom, Inc. is a fully-owned subsidiary of Plantronics Inc. Plantronics Limited is 100% owned by Plantronics BV. Polycom is a trademark of Plantronics Inc. registered in the EU, UK, US and other countries.

© 2021 Plantronics, Inc. All rights reserved. Poly, the propeller design, and the Poly logo are trademarks of Plantronics, Inc. All other trademarks are the property of their respective owners.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>