Xiaomi YTXJ07FM Palm 2 Pro Gimbal Camera User Manual

Xiaomi YTXJ07FM Palm 2 Pro Gimbal Camera User Manual

Pleas read this manual carefully before use.

Product Introduction

Charging

To charge PALM2, please use the included USB cable to connect it with the USB—C port in maximum charging current of 5V2A. While charging, the status LED is always on. When the battery is fully charged,the status LED is oP.

The equipment of external MIC

Please equip the MIC as shown.

Inserting the MicroSD Card

Please insert the MicroSD Card as shown. It is recommended to use a microSD card with or over a UHS— III Speed Grade 3 rating. The PALM 2 supports atmost SDcardwith 256G(not included), and you can format the SD card on PALM 2.

Operations

1. Power/Shutter Button
   

Status

|

Instruction

---|---

Long press

| Turn on or turn off the PALM

Short press

| Take a capture according to current shooting mode

Double click

| To recenter the gimbal
2. Direction joystick
**

Status

| Instruction| Remarks
---|---|---

Move up

| To control the gimbal camera move up| Mode 1
Move down| To control the gimbal camera move down|

Mode 1

Move left

| To control the gimbal camera move left|

Mode 1

Move right

| To control the gimbal camera move right| Mode 1
Move up| zooM +|

Mode 2

Move down

| ZoOM —|

Mode 2

Move left

| Ev —|

Mode 2

Move right| EV+|

Mode 2

P.S. Click the “ ” on the top right of screen to switch mode 1 and mode 2.****

3. Touch Screen
   

Status

| Instruction
---|---

Swipe right/left

|

To switch shooting mode

Swipe down

| To enter setting mode
Swipe up|

To enter media library

Double click

| Turn on /turn off Face Tracking
Double click the selfie button|

To switch selfie mode

Long click the selfie button|

To center the gimbal

4. Status LED
   

Status

| Instruction
---|---
Green light is on|

Normal

Green light flashes

| Recording
Red light is on|

Low battery or the gimbal is abnormal

Red light flashes

| System is abnormal
Red and green light alternatively.|

Firmware is updating

Downloading AP

Please scan the QR code or search for downloading the FIMI PLAY APP in APP Store or Google Play.

Maintenance and Calibration

1. The PALM 2 enters the self—check when it is powering.
2. Gimbal camera is a high-precision control device. Please do not drop it or have it hit by external And please ensure that the gimbal doesn’t be blocked by outside forces when it is moving. Otherwise, the machine might be damaged and be led to abnormal operations.
3. Do not place the battery near Lithium battery’s capacity reduces significantly in low temperature conditions. Please do not use the PALM 2 if the temperature is below 0 celsius degree.

Basic Specification

Name: PALM 2 Gimbal Camera
Model: YTXJ07FM
Dismensions: 32.535.5132.Smm
Net Weight: 145g (accessories are not included) Precision Control: + 0.005°
Rolling Angle: YAW: —240°- + 60° ROLL: :ñ 45°
PITCH: + 90°
Battery Capacity: 2600 mAh
Rated Power: 9.62 W Rated Voltage: 3.7V
Operating Temperature: 0°C-40°C
Wireless Connectivity: Wi—Fi IEEE 802.11b/g/n
Product standard: Q/BJFMK0006—2017
CMIIT ID: 2021DP1949

Check more detailed information in setting

FC Statement

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Customer Support

Manufacturer: Shenzhen Fimi Robot Technology Co., Ltd. (a Mi Ecosystem company)
Address: 2nd Floor, East Block, Tianliao Building, 1133 Xueyuan Avenue, Taoyuan Street, Nanshan District, Shenzhen City, Guangdong Province,China

Official website: www.fimi.com
Online service: support@fimi.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>