behringer KXD15 600-Watt 4-Channel PA System / Keyboard Amplifier User Guide
- June 6, 2024
- Behringer
Table of Contents
behringer KXD15 600-Watt 4-Channel PA System / Keyboard Amplifier
Important Safety Instructions
-
Terminals marked with this symbol carry an electrical current of sufficient magnitude to constitute risk of electric shock.
-
Use only high-quality professional speaker cables with ¼” TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
-
This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.
-
This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.
Caution -
To reduce the risk of electric shock, do not remove the top cover (or the rear section).
-
No user-serviceable parts inside. Refer servicing to qualified personnel.
Caution -
To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.
-
Caution
These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.
-
Read these instructions.
-
Keep these instructions.
-
Heed all warnings.
-
Follow all instructions.
-
Do not use this apparatus near water.
-
Clean only with dry cloth.
-
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
-
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
-
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
-
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
-
Use only attachments/accessories specified by the manufacturer.
-
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
-
Unplug this apparatus during lightning storms or when unused for long periods of time.
-
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
-
The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
-
Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
-
Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE
Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office, or your household waste collection service. -
Do not install in a confined space, such as a book case or similar unit.
-
Do not place naked flame sources, such as lighted candles, on the apparatus.
-
Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed-of at a battery collection point.
-
This apparatus may be used in tropical and moderate climates up to 45°C.
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community.musictribe.com/pages/support#warranty.
ULTRATONE KXD15/KXD12 Hook-up
Step 1: Hook-Up
Practicing setup using the ULTRATONE.
Live/entertainer setup
ULTRATONE KXD15/KXD12 Controls
Step 2: Controls
- FX controls adjust the channel 1-4 signal level at the input of the integrated effects processor.
- TO LINE OUT button routes the channel 4 signal to the LINE OUT output without effects. If you press both the TO MAIN and TO LINE button, channel 4 will be equal to channels 1 – 3. The signal will be routed to the speakers and the LINE OUT output including effects.
- GRAPHIC EQ adjusts specific frequencies in the sound spectrum.
- MULTI-FX PROCESSOR unit adds a selected sound effect to any channels which have their FX knob turned up. Effects include reverb, chorus, delay, and pitch shifter.
- PROGRAM [PUSH] knob controls the effects settings. Rotate this knob to scroll through effects patches, and push to select a patch.
- FX RET knob controls the amount of effects added to the main mix.
- PHONES jack allows connection of headphones using ¼” TRS stereo connectors.
- LEVEL controls adjust the signal level of channels 1-4.
- TO MAIN routes the channel 4 signal to the speakers without effects. When disengaged, the channel 4 signal normally routes to the PHONES output without effects.
- FBQ button activates the FBQ Feedback Detection system. The frequencies causing feedback are shown by the brightly lit fader LEDs. Simply lower the level of the respective frequency range until feedback disappears and the LED goes out.
- CLIP LED lights when the signal from the channel FX sends overloads the processor. When the CLIP LED lights up please reduce the effects input signal by using the respective FX control(s).
- SIG LED lights up when the effects processor receives an input signal.
- FX display shows the currently selected preset.
- LEVEL control in the master section is used to adjust the main output volume.
- SHAPE button applies a special filter to the MASTER output to increase the sound’s clarity and definition in noisy environments.
- PHONES LEVEL control adjusts the headphones output level.
- POWER switch turns the unit on or off. You should always make sure that the POWER switch is in the “Off” position when initially connecting the unit to the mains.
- POWER SOURCE jack accepts the included IEC power cable.
- LINE OUT connectors send out a post-EQ audio signal to external devices. The XLR connectors provide a balanced signal suitable for connection to mixing or recording consoles, while the 1/4″ connectors provide an unbalanced signal suitable for additional amplifiers or other line-level devices. Both XLR and 1/4″ connectors may be used simultaneously.
- STEREO LINK connection allows for true stereo operation between two ULTRATONE amplifiers. You can connect the OUT of one ULTRATONE to the LINK IN of another keyboard amp which then serves as slave to achieve a true stereo sound.
- AUX IN connection accepts signals from CD players, MP3 players or other sound sources using RCA connectors.
- LINE inputs for channels 2-4 accept unbalanced stereo signals through paired ¼” TS connectors. For mono input signals please use the L (MONO) connector.
- LINE /MIC input section for channel 1 features an additional XLR connection in addition to dual 1/4″ TS connectors. Use the XLR connection for balanced signals from microphones or other devices (+15 V phantom power is available to power condenser microphones). Both XLR and 1/4″ connectors can be used simultaneously, while the channel 1 LEVEL control adjusts the signal level for both inputs.
- GND LIFT switch disconnects (switch pressed) the ground connection at the LINE OUT XLR outputs to eliminate hum and other noise resulting from ground loops.
- SUB OUT connector provides the line-level mono subwoofer signal for connection to the input of a power amp or active subwoofer.
- FOOT SW jack connects an optional footswitch using a footswitch using a 1⁄4″ TS plug to activate/deactivate the effects processor.
Specifications
Important information
- Register online. Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.
- Malfunction. Should your Music Tribe Authorized Reseller not be located in your vicinity, you may contact the Music Tribe Authorized Fulfiller for your country listed under “Support” at musictribe.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at musictribe.com. Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.
- Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.
ULTRATONE KXD15/KXD12
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by MUSIC Tribe can void the user’s authority to use the equipment. Hereby, Music Tribe declares that this product is in compliance with Directive 2014/35/EU,Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/ EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address : Gammel Strand 44, DK-1202 København K, Denmark
UK Representative: Music Tribe Brands UK Ltd.
Address : 6 Lloyds Avenue, Unit 4CL London EC3N 3AX, United Kingdom.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>