FS IPC201-2M-D Full HD 2MP Dome Network Cameras User Guide

FS IPC201-2M-D Full HD 2MP Dome Network Cameras

Accessories

NOTE: The installation position map varies according to the different models of cameras.

Hardware Overview

Ports

separately)to get a local storage

Buttons

Reset Button

| Press and hold the reset button for more than 15 seconds to restore factory default settings. Perform t his operation within 10 minutes after the device is powered on or the reset will fail otherwise.

Installation Requirements

•  Installation and removal of the device and its accessories must be carried out by qualified personnel.
• Store or use the device in a proper environment that meets environmental requirements, including and not limited to, temperature, humidity, dust, corrosive gases, electromagnetic radiation, etc.
•  Make sure the device is securely installed or placed on a flat surface to prevent falling.
•  Unless otherwise specified, do not stack devices.
• Ensure good ventilation in the operating environment. Do not cover the vents on the device. Allow adequate space for ventilation.
• Protect the device from the liquid of any kind.
•  Make sure the power supply provides a stable voltage that meets the power requirements of the device. Make sure the power supply’s output power exceeds the total maximum power of all the connected devices.
•  Take proper waterproof measures in accordance with requirements before using the device outdoors.
• Using the device may involve the collection of personal information such as the face, fingerprint, license plate number, email, phone number, GPS. Please abide by your local laws and regulations while using the device.

Mounting the Camera

Installing Micro SD Card (Optional)

Take off the transparent dome cover by loosening screws.

Insert the Micro SD card (purchased separately) into the camera.
Do not hot plug the Micro SD card after it is inserted. Otherwise the camera or the Micro SD card might be damaged.

Installing Waterproof Connector (Optional)

Install the supplied waterproof components to the Ethernet cable in sequence.

NOTE: Please use self-adhesive waterproof tape (purchased separately) to protect the cables.

Ceiling Mount

Locate the positions of the holes by pasting the installation position map on the ceiling, and lead the cables through the hole on the ceiling.
Drill holes with a diameter of 6 – 6.5 mm and a depth of 30 mm in the marked locations. Knock the plastic rivets of self-tapping screws into the guide holes and ensure that they are tightened up. Take off the transparent dome cover by loosening screws.
Connect all cables of the ceiling and the camera.
Secure the camera to the ceilingl by leading the self-tapping screws through the guide holes in the base and fix them by using a screwdriver.

NOTE: The installation process above is concealed installation, during which holes are drilled in the ceiling and tail cable is led out from the top of the camera. Cables are connected and frapped at the ceiling side to prevent messy cables from affecting camera mounting. If open installation is adopted, tail cable is led out from one side of the camera and can be routed from the side groove of the camera. Adjust the monitoring direction of the lens horizontally or vertically by rotating the lens base or loosening the fastening screws. Tighten the screws after vertically adjusting the lens.

NOTE: Please stop rotating the camera when the lens is blocked, otherwise the camera lens might be damaged.

Align the screw holes in the base and tighten screws on the edge of the transparent dome cover to fix it.

Connecting the Power

PoE Device

Use an Ethernet cable to connect the network interface of the camera to the PoE port on a PoE device, such as a PoE switch.
Power Adapter

Use the power adapter (purchased separately) to connect the power interface of the camera to the local power source.

Configuring the Camera

Step 1: Connect the computer to the camera on the same LAN.
Step 2: Set the IP address of the computer to 192.168.1.x.
(“x” is any number from 2 to 254.)

Step 3: Open a browser, type http://192.168.1.13, and enter the default username and password, admin/admin.

Step 4: Click Login to display the web-based configuration page

NOTE: You may need to install a plug-in at your first login. Please follow the on-screen instructions to complete the installation and then open the browser again to log in.

Support and Other Resources

Download https://www.fs.com/download.html
Help Center https://www.fs.com/service/help_center.html
Contact Us https://www.fs.com/contact_us.html

Product Warranty
FS ensures our customers that any damage or faulty items due to our workmanship, we will offer a free return within 30 Days from the day you receive your goods. This excludes any custom-made items or tailored solutions.

Warranty: Dome network cameras enjoy 2 years limited warranty against defect in materials or workmanship. For more details about warranty, please check at
https://www.fs.com/policies/warranty.html
Return: If you want to return item(s), information on how to return can be found at
https://www.fs.com/policies/day_return_policy.html

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>