Guangzhou U I Technology BS346FN TWS Bluetooth Earbuds User Manual
- June 6, 2024
- Guangzhou U I Technology
Table of Contents
- Specifications
- Structure sketch
- Earbuds Indicator and Prompt
- Charging Case Indicator
- Wear earbud (R)/(L) respectively
- How To Wear
- How To Charge Earbuds
- How to Charge Charging Case
- Turning ON/OFF
- TWS Pairing
- Single Pairing Mode by Manual
- Two-call Handling
- Maintenance
- Trouble Shooting
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
**Guangzhou U I Technology BS346FN TWS Bluetooth Earbuds User Manual
**
Bluetooth earbuds should be used with the compatible devices which support
bluetooth wireless technology, making calls and enjoying music at any time
freely.
Please read this user manual carefully, and also read your device’s user
manual about bluetooth functions carefully before using.
Please pay attention to those important safety and maintenance information.
Please keep your earbuds away from children.
Specifications
Bluetooth Version: V5.2
Bluetooth Profiles Supported: HSP, HFP, A2DP, AVRCP
Audio Decoding Protocol: SBC, AAC
Transmission Power: Class 2
Operation Range: Up to 10 meters
Frequency Range: 2.4GHz-2.48GHz
Battery of Earbuds: 45mAH Li-polymer Battery
Charging Voltage of Earbuds: DC 5V±0.2V
Charging Time of Earbuds: DC 5V±0.2V
Battery of Base: 380mAH Li-polymer Battery
Charging Voltage of Charging Case: DC 4.75V-5.25V
Charging Time o f Case: About 1~1.5 hours
Charging Earbuds from Charging Case: 2-3 times
Music Playing Time: ≥ 7 hours (50% volume)
Talk Time: ≥ 4 hours (50% volume)
Standby Time of TWS connect with mobile: About 70 hours
Driver Diameter: φ12mm
Driver sensitivity : 114±1.5dB (1KHz)
Driver impedance: 32Ω±15%
Driver frequency response: 20Hz-20KHz
ANC frequency response: 80Hz-1.5KHz
ANC average depth: ≥22dB
ANC maximum depth: ≥30dB
Dimensions of Charging Case (mm): L61×W45.5×H31.1
Dimensions of earbuds (mm): L34×W22.2×H23.5
Weight (single earbud): About 4.9g
Total Weight: About 48g
Charging Ambient: 0℃~45℃
Non-charging Ambient: -10℃~60℃
Storage Ambient: -20℃~40℃
*The time mentioned above may vary due to user’s operation habits and device settings.
GuangZhou U&I Technology Company Limited
Structure sketch
- Charging case opening snap
- Charging case button
- Charging case indicator
- Charging case type-C port
- Earbud noise cancellation mic hole
- Earbud touch panel
- Eartips
- Earbud calling mic hole
Earbuds Indicator and Prompt
No
| Status| Operation|
Prompt
---|---|---|---
1| Power on| Open the charging case or long touch the earbuds for 2 seconds.|
Power on
2| Power off| Put the earbuds into the case and close the cover.| Power off
3
| Enter TWS pairing mode| Open the charging case and do not pick up the earbuds, long press the button of charging case for 10 seconds to reset.|
Du
4
|
TWS Pairing
| Open the charging case or long touch the earbuds for 2 seconds to power on, the earbuds will automatically connect with each other.|
/
5
| Connecting with
phone
| After TWS pairing successfully, using mobile to search “BS346FN”.| Pairing
6| Connected
successfully
| Using mobile to search “BS346FN” and select from Bluetooth list.| Connected
7| Low battery
alarm
| When the battery less than 20%, there will be a
low battery alarm.
| Low battery
8
|
Reset
| Open the charging case and do not pick up the earbuds, long press the button of charging case for 10 seconds to reset.|
/
9| Charging| Put the earbuds into the case and close the cover.| /
Charging Case Indicator
No
| Status|
Indicator Light
---|---|---
1| Charging| When charging the base, the indicator light keeps on red, and
then will keep on green after fully charged.
2| **** Battery indication| The indicator off when charging case less than 5%
battery. 5-20%: the light quickly flashes red.
20%-50%: the light keeps on red. 50%-80%: the light keeps on orange.
>80%: the light keeps on green.
**** 3
| ****
Earbuds checking
| The indicator off when charging case less than 5% battery. 20%-50%: the light keeps on red.
50%-80%: the light keeps on orange.
>80%: the light keeps on green.
Wear earbud (R)/(L) respectively
How To Wear
Step 1
Put earbud into cochlea as show
Step 2
Slightly rotate earbud until firmly
Step 3
Put the earbud to cochlear edge tightly
How To Charge Earbuds
Put earbuds into the case for charging.
The indicator off when charging case less than 5% battery
5-20%: the light quickly flashes red.
20%-50%: the light keeps on red.
50%-80%: the light keeps on orange.
>80%: the light keeps on green.
Notice: When charging case in 5-20% battery, the case needs to be charged, and will not charge the earbuds
Put earbud(L and R) to the corresponding position in the charging case.
How to Charge Charging Case
-
Use the Type-C cable for charging.
When charging to the base, the indicator light keeps on red, and then will keep on green after fully charged. -
Use Type-C cable to connect with computer
-
Use Type-C cable to connect with mobile phone charger
Note 1 : Check charging device whether it is suitable for your earbuds or
not before charging.
Note 2 : Use only the supplied charger to charge your earbuds. Other
device may violate the validation or the maintenance article of this product
and cause danger.
Note 3 : Do not try to open the built-in battery as this will damage your
earbuds.
Note 4: Earbuds will lose its power automatically if un-used. In this
case, fully charge your earbuds every 3-6 months.
Note 5: Do not expose of your earbuds into fire or water.
Turning ON/OFF
Method
Turn on: Open the charging case cover to turn on. It’s better to wait for 1
second before pick up earbuds for using.
Turn off: Put earbuds into the charging case and close the cover, the earbuds
will turn off automatically 3 seconds later.
Note: Please do not open and close the cover too frequently.
Method
Turn on: Touch earbuds for 2 seconds.
Turn off: Disconnect with bluetooth device for 5 minutes, the earbuds
will turn off automatically
TWS Pairing
-
TWS Pairing
-
Long touch the panel for 2 seconds to turn on, the earbuds will enter auto-pairing mode, waiting for a few seconds, the two earbuds will pair automatically, then use mobile to search .
2. Open the charging case cover, the earbuds in case will enter auto-pairing mode, waiting for a few seconds, the two earbuds will pair automatically, then use mobile to search.
-
Pairing with Mobile
-
After TWS pairs successfully and connected with the mobile, the earbuds prompt “connected”.
-
When the earbuds disconnects with the mobile, the earbuds prompt “Disconnected”, and the master earbud enters pairing mode.
If the earbuds don’t connect with mobile within 5 minutes, they will turn off automatically.
Do as the above ways:
Using the mobile to search “BS346FN” and select it from Bluetooth list (Please refer to the bluetooth device user manual).
After connected with Bluetooth device, the earbuds will prompt “connected”.
TWS Reconnected
Method 1:
Touch the earbud(R/L) for 2 seconds to power on→wait for a few seconds, the
two earbuds will connect automatically→the earbuds will connect with the
mobile phone that has ever paired after a few seconds → reconnected
successfully.
Method 2:
Open the charging case to power on→wait for a few seconds, the two earbuds
will connect automatically→ the earbud will pair with the mobile phone that
has ever paired after a few seconds →reconnected successfully.
Single Pairing Mode by Manual
- If without pairing record, double tap the panel after turning on, the earbuds will enter into pairing mode, and keep for 1 minute.
- If TWS has pairing record, please turn off the bluetooth function of connected devices firstly. The earbud will immediately enter into pairing mode and keep for 1 minute. ( During pairing mode, if turn on the other earbud, they will connect.)
Answer / End a Call
When call coming, double tap the earbud(R/L) to answer the call. In phone calling mode, double tap the earbud(R/L) to end the call.
Reject a call
When call coming, long touch the earbud(R/L) for 2 seconds to reject the call.
Two-call Handling
When you are answering a call, there is another call coming :
- Long touch the earbud(R/L) for 2 seconds to end the current call and answer the incoming call;
- Double tap the earbud(R/L) to hold the current call and answer the incoming call;
- After the second implementation, double tap the earbud(R/L) to switch between two calls;
- After the second implementation, long touch the earbud(R/L) for 2 seconds to end the current call, and double tap the earbud(R/L) to end the other call.
Note:
To use the above functions, the mobile must support the Bluetooth hands free
profile V1.5 and the mobile holding function (Network services from telecom)
from has been started.
Music Playing/Pause
In music playing mode, single touch the earbud(R/L) to pause music; In pause mode, single touch the earbud(R/L) to play music.
Voice Assistant
In connection mode, triple tap the earbud(L) to activate voice assistance, then triple tap the earbud(L) to exit.
ANC / Transparency Mode Switch
In Power ON Mode, long touch the earbud(R/L) for 2 seconds to switch normal /
transparency / ANC mode.
In ANC mode, R&L prompts “ANC on”, in transparency mode, R&L prompts
“Transparency on”, in normal mode, R&L prompts “All off”.
Gaming Mode
In Power ON Mode, triple tap the earbud(R) to enter gaming mode, R&L prompts “Gaming mode on”, then triple tap the earbud(R) to exit gaming mode, R&L prompts “Gaming mode off”.
Next / Previous Track
When in playing music mode, double tap the earbud(R) for next song. Double tap the earbud(L) for previous song.
Reset
Put the earbuds in the charging case, open the charging case cover and long press the reset button for 10 seconds, the charging case indicator flashes blue for 10 seconds quickly. Waiting until the indicator light turns off.
Maintenance
- Do not use abrasive cleaning solvents to clean your earbuds.
- Prevent your earbuds from touching any sharp objects.
- Keep your earbuds away from high-temperature, humidity and dust.
Trouble Shooting
Trouble
|
Reasons
|
Solutions
---|---|---
The earbuds fail to reconnect / earbuds noisy, can not operate| The earbuds
broken down| Put the earbuds into the charging case and close the cover for 20
seconds to let earbuds resume normal
Unable to turn on by opening charging case cover or touching earbuds area|
Without enough battery capacity in the charging case or earbuds| Charge the
earbuds and case at same time for 1-2 hours, to ensure that the product has
power
No sounds after pairing| Pairing failure or pairing
overtime
| Reset the earbuds and repairing
TWS paired, but can not search in mobile| The earbuds has too many pairing
records| Reset the earbuds and repairing
The charigng case has no indication after the earbuds are put inside| Without
enough battery capacity in charging case / earbuds metal pin poor contact|
Charge the case for about 1-2 hours/check whether the earbuds are put in
position or the dirty matal pin leads to poor contact
One earbud no sound after connect with
mobile
| The earbud fails to connect with mobile| Reset the earbuds and repairing
Turn off automatically| Low battery| Charge the earbuds for 1-2 hours
Earbud echo| Volume is too loud or
environment is noisy
| Adjust volume on phone or
change a place
Noise in call| Environmental interference or out of working range| Change
place or go back to working range
Low voice of the calling party| Wrong Wearing| Follow wearing instructions
The charging case flashes blue every 1 second| Earbuds metal pins might be
dirty, leading to short and over current, activating
over-current protection
| Clean the earbuds metal pin, put the earbuds back to the charging case,
close and open the top cover, earbuds will resume normal
Earbuds single / double / triple touch failure| Time of double / triple touch
is too long or touching operation failure| Double / Triple touching should be
finished within 700ms. Put the earbuds to the charging case to wake up if
touching operation failure
The earbuds fluzzing when touch the area| Block the mic hole during touch|
Resume normal after put hands down
Without obvious ANC effect| Earmuffs sealing not good| Adjust to correct
wearing position or replace with suitable earmuffs size, to ensure the
earmuffs fit for wearing
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>